Revisit the Pitot static tubes in the standards

A Pitot tube is a popular device used for the measurements of flow fields. To control the accuracy of the Pitot tube coefficient, the international standard organization (ISO), the American Society for Testing and Materials (ASTM), and the Japanese Industrial Standards (JIS) issued guidelines that recommended the shape and working conditions of these devices. However, many Pitot tubes on the market do not follow these guidelines. In the present study, various types of Pitot tubes in the market were tested at the National Metrology Institute of Japan (NMIJ) to determine the effects of the geometry and flow characteristics. The results revealed certain limitations in the existing ISO and JIS standards, specifically with regard to the recommended design parameters of the AMCA Pitot tube, the reference coefficient value for the JIS Pitot tube, and the redefinition and limitation of Reynolds numbers pertaining to Pitot tube working conditions.     

Effects of Winding Attachment Positions on Output Characteristics of Flux‐Modulating Synchronous Machines

The flux‐modulating synchronous machine (FMSM) is a new type of multipole SM with nonoverlapping concentrated armature and field windings on the stator. This paper compares the output characteristics of two FMSMs through finite element analysis (FEA) and experiments. In both of the FMSMs, the attachment positions of the armature and field windings are swapped. To determine the reason for the discrepancies in their output characteristics, unsaturated inductances were calculated using a d‐‐q equivalent circuit. In addition, the calculated results of the inductances were confirmed through a visualization of the leakage fluxes using FEA. The results of the study show that the synchronous inductance can be reduced by attaching the armature winding to the air‐gap side of the stator teeth and that the reduction leads to an increase in output power.     

钢管套筒灌浆连接轴向受拉性能模拟试验研究

为研究钢管套筒灌浆连接轴向受拉破坏过程及破坏机理，试验中设计了16组48个钢管套筒灌浆连接试件，试件采用钢板代替圆钢管，并进行静载试验。分析了灌浆料裂缝扩展过程、荷载-相对位移曲线，并对抗剪键高距比、灌浆料厚度、侧向力等因素对破坏过程及承载力的影响进行分析。结果表明：对于不设置抗剪键的套筒灌浆连接试件，斜裂缝随机产生，裂缝分布不均匀；对于设置抗剪键的套筒灌浆连接试件，裂缝首先出现在底部抗剪键位置处，与水平方向夹角约为30°，随后在中部和上部抗剪键位置处分别出现斜裂缝。由于每个抗剪键上荷载分担并不均匀，与抗剪键接触的灌浆料逐渐达到极限压应力，达到极限状态时，承载力全部由抗剪键间的机械咬合力承担，在连接承载力中，可忽略摩擦力和胶结力作用。随着抗剪键高距比h/s增大，各试件初始剪切刚度相差不大，承载力增大，但增幅逐渐减小，建议抗剪键高距比0.06g/s>0.3，同时需要满足灌浆料灌注的施工要求。     

Designed damping controller for SSSC to improve stability of a hybrid offshore wind farms considering time delay

This paper presents the stability improvement results of hybrid doubly fed induction generator (DFIG)-based and permanent magnet generator (PMG)-based offshore wind farms (OWFs) using a static synchronous series compensator (SSSC). An adaptive-network-based fuzzy inference system (ANFIS) controller of the proposed SSSC is designed to render adequate damping characteristics to the studied system. A frequency-domain approach based on a linearized system model using eigenvalue technique analysis is performed. A time-domain scheme based on a nonlinear system model subject to a three-phase short circuit fault at infinite bus with variations in the signal transmission delays has also been investigated to compare the damping of the studied system in cases of with and without controller. The simulation results with MATLAB/SIMULINK toolbox have been presented. It can be concluded from the simulation results that the proposed SSSC joined with the designed ANFIS damping controller can offer adequate damping performance to the studied hybrid DFIG-based and PMG-based OWFs under severe disturbance.     

Topology optimization for crashworthiness of thin-walled structures under axial crash considering nonlinear plastic buckling and locations of plastic hinges

Although topology optimization is established for linear static problems, more effort is required for solving nonlinear plastic problems. A new topology optimization approach with equivalent static loads (ESLs) is suggested to find the optimum topologies and locations of plastic hinges of thin-walled crash boxes by considering crash-induced deformation, the main crash energy-absorbing mechanism. Together with finite element method crashworthiness analyses, considering all nonlinearities with rate-dependent plasticity, the method was developed using an appropriate time-incremental scheme of ESLs without removing any high values of loads. Analyses show that the crash boxes with optimum topologies have energy-absorbing capabilities equivalent to the original structure. The proposed method is evaluated for two crashes: a crash box at low speed and a double cell subjected to high-speed collision. The results indicate that this method captures nonlinear crushing behaviours and accurate locations of plastic hinges where, if proper reinforcements are made, energy absorption can be enhanced.     

基于DSP的多元数据同步采集与存储系统的设计与实现

从硬件和软件两个角度出发,介绍基于DSP的多元数据同步采集与存储系统的组成、工作模式以及功能的测试。系统主要由上位机和数字采集与存储单元组成,其中数字采集与存储单元的硬件部分包括电源模块,值班电路模块,数据采集模块,数据存储模块,时钟同步模块。系统采用DSP作为中央处理芯片,利用经过同步后的秒脉冲作为触发信号,实现同步数据采集。以CF卡作为存储介质,实现数据自容式存储。软件部分实现自检、同步、数据采集存储功能。经过测试,系统工作稳定,功能正常,同步精度在100ns以内。     

Animations showing Lego manipulative tasks: Three potential moderators of effectiveness

Evidence suggests that transient visual information, such as animations, may be more challenging to learn than static visualizations. However, when a procedural-manipulative task is involved, our evolved embodied cognition seems to reverse this transitory challenge. Hence, for object manipulative tasks, instructional animations may be more suitable than statics. We investigated this argument further by comparing animations with statics using a Lego task shown to university students, by examining three potential moderators of effectiveness: (a) the environment of manipulation (virtual or physical), (b) the quality of visual information (focused or unfocused), and (c) the presence of hands (no hands or with hands). In Experiment 1 we found an advantage of animation over statics, and no differences among the environments. In Experiment 2, we again observed an animation advantage, a small advantage of focused static information compared to unfocused static information, and a positive effect of not showing the hands.     

轻质滤料滤池的试验与研究

轻质滤料滤池是以比水密度略小的滤料为滤床的滤池，通过以净水厂的原水和污水处理厂的二级处理出水为过滤试验对象，所取得的结果表明：下向流轻质滤料滤池对浊度和悬浮固体（SS）的去除率分别可以达到80％和45％，而滤床的水头损失不超过15cm。因此轻质滤料滤池可以以预过滤的形式配置在过滤处理的净水和污水的处理工艺中。     

基于对比折射法的三维静校正技术及其应用

在地形起伏剧烈、速度和厚度横向变化大的地区，折射静校正技术的应用受到诸多限制，主要表现在不能准确地识别和拾取来自于地下连续地质界面的折射波，使得精确求取的长波长静校正量困难。为此，提出了一种基于对比折射法的三维静校正技术。介绍了这种静校正技术的方法原理和特点，基于对比折射法的折射波至拾取实质上是一个折射层的对比分析解释过程，因此能准确地拾取折射波至，精确地求解低速带的绝对延迟时；然后利用延迟时和近地表速度模型（等效，时深，空变）反演表层模型，最终一次性完成基准面静校正（包含低速带校正和高程校正）。在黄土塬、沙漠以及沙漠和山地的接合部等地区，利用基于对比折射法的三维静校正技术进行静校正处理，使资料的品质得到了明显改善，反射同相轴连续性好，信噪比和分辨率高，构造形态清晰可靠，提高了勘探精度。