LTE系统多小区上行联合功控算法

针对传统的小区内开环功率控制算法通常以提升本小区的吞吐量性能为目标，忽略了当前小区用户对邻小区用户同频干扰的问题，为提升边缘用户性能的同时兼顾系统整体性能，提出了一种LTE系统小区间上行联合功率控制（UJPC）算法。该算法采用单基站三扇区为系统模型，以最优化系统吞吐量比例公平函数为目标，首先根据最小信干噪比（SINR）约束值和用户最大发射功率这两个约束条件得到相应的数学优化模型，然后采用连续凸近似的方法求解优化问题得出各个基站所管辖的小区内所有用户的最优发射功率。仿真结果表明，与基准的开环功控方案相比，联合功控方案在保证系统平均频谱利用率的情况下能够较大幅度地提高小区边缘频谱利用率，其最佳性能增益能达到50%。     

An experimental study on the pumping performance of molecular drag pumps

The pumping performance of molecular drag pumps (MDP) has been investigated experimentally. The experimented MDPs are a disk-type drag pump (DTDP), helical-type drag pump (HTDP) and compound drag pump (CDP), respectively. In the case of the DTDP, spiral channels of a rotor are cut on both upper surface and lower surface of a rotating disk, and the corresponding stator is a planar disk. In the case of the HTDP, the rotor has six rectangular grooves. The CDP consists with the DTDP, at lower part, and with the HTDP, at upper part. The experiments are performed in the outlet pressure range of 0.2–533 Pa. The inlet pressure and compression ratio are measured under the various conditions of outlet pressure and throughputs, and nitrogen is used for the test gas. At the outlet pressure of 0.2 Pa, the ultimate pressure has been reached to 1.0 × 10⁻² Pa for the HTDP, 1.3 × 10⁻⁴ Pa for the DTDP, and 3.6 × 10⁻⁵ Pa for the CDP. The maximum compression ratio of the CDP is much higher than those of the DTDP or HTDP. Consequently, the ultimate pressure of the CDP is the lowest one.     

Study on high-strength composite portland cement with a larger amount of industrial wastes

It is one of important measures for the sustainable development of cement industry to utilize industrial wastes. High-strength composite portland cement with a large amount of granulated blast furnace slag (GBFS), fly ash and limestone was prepared by separate grinding method, optimizing gypsum and using activators. The total amounts of blending materials are between 45% and 65% and the strength grades of cements reach 525 or even 625 according to Chinese national standard for composite portland cement. Besides setting time and strength, the hydration heat, drying shrinkage and sulfate resistance were also determined.     

Optimizing the Vacuum Heat-Treatment of Hot-Work Tool Steels by Linear Elastic Fracture Mechanics

Linear elastic fracture mechanics was used to optimize the vacuum heat-treatment procedures for conventional hot-work AISI H11 tool steel. The fracture toughness was determined with non-standard, circumferentially notched and fatigue-precracked tensile-test specimens. The fracture-testing method is sensitive to changes caused by variations in the microstructure resulting from the austenitizing and tempering temperatures as well as the homogeneity of the material itself. The combined tempering diagram- Rockwell-C hardness, Fracture toughness K_Ic, Tempering temperature was used for the choice of the vacuum heat-treatment parameters necessary to obtain the best properties for a given application with respect to the investigated steel.     

The hydration phase and pore structure formation in the blends of sulfoaluminate-belite cement with Portland cement

Sulfoaluminate-belite (SAB) cements are an attractive class of low-energy cements from the viewpoint of saving energy and releasing less CO₂ into the atmosphere during their production. Their hydraulic activity, however, does not match that of the ordinary Portland cement (PC) and needs improvement before they can be used on their own. However, SAB cements when blended with PC have the potential to be used effectively in traditional applications as shown by this study. Mortars made with blends of SAB cements and PC, and a cement-to-sand ratio of 1:3 by weight and a water-to-cement ratio of 0.5, indicate a superior protection against corrosion of steel to those made with blends of PC and blast-furnace slag (BFSPC). The prepared mortars were stored at 20 °C for 90 days under either a 60% relative humidity (RH)-dry air, or 100% RH-wet air conditions. With further improvement in the SAB cement quality through better understanding of their characteristics, a genuine competition between SAB/PC and BFSPC can be expected in practice.     

Microstructural changes in concretes with sulfate exposure

In prior papers the responses of concretes to 50,000 ppm MgSO₄ exposure depending on cement type, w/cm and the presence of slag were described. The present paper completes this analysis by examining the effects of immersion of concretes produced using slag blended cements, in solutions containing 50,000 ppm of sodium sulfate. The spatial evolution of microstructure associated with carbonation and sulfate attack show differences which can be related to the nature of the cation associated with the sulfate, the cement type, and the w/cm ratio.     

共面转换液晶显示器中获得对比度高于1:600的新技术

薄膜晶体管液晶电视(TFT-LCD TV)因为具有薄、轻、紧凑和可随意放置的特点，已经占据了大部分电视机市场。除了这些物理特性以外，最重要的特性是已具有了良好像质的对比度。为了将对比度提高到1：600以上，对偏振片膜、背光源板、滤色片树脂、电极锥角和摩擦条件等都进行了研究。优化的背光板组合，光滑的电极锥角和摩擦方法的控制是提高对比度的主要控制因素。应用新开发的滤色片树脂，对获得高对比度最为有效。     

光链路设计的Java小程序实现

介绍光链路设计的原理和公式 ,给出光链路设计的Java小程序实现 ,以期有效解决在手工进行光链路设计及计算中存在的问题。