防垢剂BZF－2的研制与应用

桩西油田产出原油综合含水已达６０％－７０％，原用防垢剂ＨＥＤＰ已失去有效抑制集输站结垢的性能。本工作针对结垢最严重的桩５２站的应用，研制了以有机膦化合物和聚氧乙烯醚为主成份的防垢剂ＢＺＦ－２，在室内考察了不同条件下的防垢率、腐蚀性、配伍性等性能，在桩５２站进行了为期４个月的现场试验，加量为１０．３ｍｌ／ｌ、防垢率≥９８．０％，加药设备管线的腐蚀率大大降低。     

织物的拒油整理

文章概述了织物拒油整理的原理、整理方法以及对拒油整理效果的测试评价，并指出了目前拒油整理存在的问题。     

复合乳化沥青的粘附性试验方法研究

鉴于目前使用的阳离子乳化沥青粘附性试验方法难以有效评价复合乳化沥青粘附性，通过试验研究并综合考虑乳化沥青施工和路用实际情况，提出了乳化沥青水煮法试验方法和采用该方法检验复合乳化沥青粘附性时的评定标准。     

棉织物手感值的模糊综合评判研究

利用模糊综合评判数学模型对棉织物的手感值进行了计算与分析，这种方法简单、可靠，与主观评估结果有很好的一致性，为纺织生产的质量判断提供了便利。     

Micromechanical approach to damage mechanics of composite materials with fabric tensors

The purpose of this study is to apply continuum damage mechanics – introduced through the concept of fabric tensors – to composite materials within the framework of the theory of elasticity. A directional data model of damage mechanics for composite materials will be developed using fabric tensors. The introduction of fabric tensors into the analysis of damage of composite materials will allow for an enhanced and better understood physical meaning of damage. The micromechanical approach will be used here to relate the damage effect through fabric tensors to the behavior of composite materials. In this approach, damage mechanics is introduced separately to the constituents of the composite material through different constituents’ damage effect tensors. The damaged properties of the composite system as a whole can then be obtained by proper homogenization of the damaged properties of the constituents.

The derivation of a generalized formulation of damage evolution will be shown here in a mathematically consistent manner that is based on sound thermodynamic principles. Numerical examples will be presented to show applicability. In addition, damage evolution for the one-dimensional tension case is also illustrated.     

复合布尔函数中含某单乘积项的快速判定算法

引入了布尔函数的基本积、单乘积项等概念，通过实例剖析了复合布尔函数中是否含某一单乘积项的一般判定方法，在该基础上提出了一种快速判定途径，并给出了快速判定算法的具体描述，同时对算法进行了实验，结果表明该算法快速有效。     

An effective rhodium catalyst system on the synthesis of acetic acid from methyl formate

Rh/Lil/SnR₄ is an effective catalyst system for the conversion of methyl formate to acetic acid under carbon monoxide pressure. The effects of solvent and initial CO partial pressure on the turnover rate of the reaction were investigated. The possibility of replacing some of the iodide promoters by tin compounds has been probed.     

化学复合镀Ni-P-TiO_2光催化降解次甲基蓝

以钛酸丁酯为原料通过溶胶 凝胶法制备出粒径 30nm左右的纳米TiO2 ,利用化学复合镀在钢铁基底上形成Ni P 纳米TiO2 复合镀层 ,该复合镀层对次甲基蓝有较好的光催化降解作用 ,其催化性能与粉末状纳米TiO2 的催化性能大致相当。     

复杂条件下发挥锚杆支护作用的相关技术

介绍了在特殊地质和开采条件下,发挥锚杆支护作用的几种相关技术。     

40Cr钢复合热处理强韧化

用光学及电子显微镜(SEM.TEM)观察不同热处理的40Cr 钢的冲击及断裂韧性断口、及金相组织,阐明其间相互关系;断口结构可反映断裂特征,组织情况;细化晶粒提高强度、塑性和冲击韧性,但却减少脆断的特性距离 l 因而降低 K_(1c)模;减少碳(杂质)偏聚而使其呈较均匀地分布,从而减少可诱发塑坑的较粗大的碳(杂质)化合物的析出,即增加塑坑的间距 di 以及增加塑断组成物。从而都可增加断裂临界应变 ef,都可以提高 K_(1c)40Cr 复合热处理既靠先超高温淬、回火以减少碳(杂质)偏聚,改善其分布,以反增加位错马氏体从而提高 K_(1c),也靠后淬、回火细化晶粒而提高强度、塑性和冲击韧性,各自发挥长处达到强韧化。