Experimental and modeling approaches of MR behaviors under large step strains

Rheological properties of MR fluids under large step strain shear are presented in this paper. The experiments were carried out using a rheometer with parallel-plate geometry. Under the large step strain shear, MR fluids behave as nonlinear viscoelastic properties, where the stress relaxation modulus, G(t, γ), shows a decreasing trend with step strain. The experimental results indicate that G(t, γ) obeys time-strain separability. Thus, a mathematical form based on finite exponential serials is proposed to predict MR behavior. In this model, G(t, γ) is represented as the product of a linear stress relaxation, G(t), and the damping function, h(γ), i.e. G(t, γ)=G(t) h(γ). G(t) is simply represented as a three-parameter exponential serial and h(γ) has a sigmoidal form with two parameters. The parameters are identified by adopting an efficient optimization method proposed by Stango et al. The comparison between the experimental results and the model-predicted values indicates that this mathematical model can accurately predict MR behavior.     

On the linear correlation between microhardness and mechanical properties in polar polymers and blends

The tensile elastic modulus (E), yield stress (σ_Y) and microhardness (MH) of neat and binary and ternary blends of glassy semicrystalline ethylene–vinyl alcohol copolymer (EVOH), a glassy amorphous polyamide and a semicrystalline nylon‐containing ionomer covering a broad range of properties were examined. The tests were carried out on dry and water‐equilibrated samples to produce stiffer and softer materials, respectively. From the results, more accurate linear correlations were found to describe adequately the microhardness, modulus and yield stress of these strongly self‐associated polymers through hydrogen bonding. Copyright © 2003 Society of Chemical Industry     

小波变换在光谱特征提取方面的应用

人们在处理高光谱图像时一般要对一些典型地物进行光谱分析、特征波段的提取,以便提取出最大量的有效信息,剔除无用或冗余的信息,然后再进行分类识别.采用小波变换的分析方法,选用合适的小波进行分解,根据分解后的高频分量中包含的重要信息,利用局部相邻的正负极值点找出对应于原始光谱曲线上每个吸收带的左右边界;利用局部过零点,即可比较精确的提取出各个吸收带的中心波长.该方法比传统的光谱特征提取方法更简洁、有效,实验证明为一种比较理想的光谱特征提取方法.     

Mechanical properties of polyethylene mixtures crystallized under high pressure

The mechanical properties of a medium molecular weight polyethylene (MMW‐PE) and an ultrahigh molecular weight PE (UHMW‐PE) binary mixture with different weight fractions crystallized from the melt at 0.1 and 450 MPa were studied. The tensile modulus, yield stress, and strain were obtained as a function of the weight fractions in the PE mixtures at 25 and 85°C. The tensile modulus in the sample crystallized at 0.1 MPa decreased from 1.5 GPa of pure MMW‐PE to about 0.4 GPa of pure UHMW‐PE with the UHMW‐PE content but it did not decrease with the UHMW‐PE in the sample crystallized at 450 MPa in testing at 25°C. A decreasing rate of the storage modulus E′ of UHMW‐PE in a dynamic measurement for the sample crystallized at 0.1 MPa with the temperature is larger than that of the sample crystallized at 450 MPa. These experimental facts are interpreted in relation to the molecular motion and crystallinity of the sample. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1962–1968, 2003     

Materials modelling: A bridge from atoms to bulk properties

The use of molecular-level materials modelling techniques in the development of advanced performance polymers is discussed, with particular emphasis upon bridging the large difference in the scales of dimensions between atomic structure and fabricated parts. The advantages and disadvantages of bulk quantitative structure-property relations and atomistic modelling are assessed, and the method of group interaction modelling is suggested as a means of bridging the dimensional scales.After a brief introduction to the concept of group interaction modelling, examples of modelling the engineering properties of polymers are presented which are difficult to model quantitatively by any other means. The important phase transitions from the crystal and glassy states of matter to those of rubber- and liquidlike states are shown quantitatively to be due to the same isoenergetic condition. The viscoelastic properties of a polymer are critical for many applications and expressions are derived for the loss and storage components of the complex modulus, with reference to failure initiation conditions. The effect of crosslinking in thermosets upon the glass transition temperature and viscoelastic properties is outlined. Finally, the scaling of time from atomic vibrations to the years involved in creep and ageing effects are discussed.     

Model Validation for Bridge-Road-Vehicle Dynamic Interaction System

The dynamic response of highway bridges subjected to moving truckloads has been observed to be dependent on (1) dynamic characteristics of the bridge; (2) truck configuration, speed, and lane position on the bridge; and (3) road surface roughness profile of the bridge and its approach. Historically, truckloads were measured to determine the load spectra for girder bridges. However, truckload measurements are either made for a short period of time [for example, weigh-in-motion (WIM) data] or are statistically biased (for example, weigh stations) and cost prohibitive. The objective of this paper is to present results of a 3D computer-based model for the simulation of multiple trucks on girder bridges. The model is based on the grillage approach and is applied to four steel girder bridges tested under normal truck traffic. Actual truckload data collected using a discrete bridge WIM system are used in the model. The data include axle loads, truck gross weight, axle configuration, and statistical data on multiple presence (side by side or following). The results are presented as a function of the static and dynamic stresses in each girder and compared with code provisions for dynamic load factor. The study provides an alternate method for the development of live-load models for bridge design and evaluation.     

Dynamic vulcanisation of EPDM/PE-based thermoplastic vulcanisates studied along the extruder axis

Simple blending and dynamic vulcanisation of EPDM/PE blends using the resol/SnCl₂ system was studied in an extruder using a series of sampling devices. The melting of the PE pellets occurs just in front of and in the first kneading zone. Upon complete melting of the PE phase, the EPDM/PE blends reach very quickly their final morphology. Crosslinking of the EPDM phase to high levels occurs already when the PE phase is not yet fully molten. The higher the EPDM content, the higher the viscous dissipation, the higher the melt temperature and, consequently, the higher the crosslinking rate. For the EPDM/PE (50/50; w/w) TPV a transition from continuous via co-continuous to fully dispersed EPDM is observed, which is driven by crosslinking. Although the degree of crosslinking of the EPDM rubber is very high, this does not prevent phase inversion of the blend. The EPDM/PE interface is rather blurred, because PE crystalline lamellae are growing into the EPDM domains, probably because of the high compatibility between PE and EPDM (60 wt% of ethene). This study shows that dynamic vulcanisation in extruders proceeds quite differently from that in batch kneaders, where melting, mixing and crosslinking are separated in time. In extruders mass and heat transport, melting of the thermoplastic, morphology development (including dispersion and phase inversion), distribution and dissolution of (crosslinking) chemicals and crosslinking of the rubber do not occur as independent phenomena, but mutually and/or continuously interact.     

Prediction and quality control of the melt index during production of high-density polyethylene

In polyolefin processes the melt index (MI) is the most important control variable indicating product quality. Because of the difficulty in the on-line measurement of MI, a lot of MI estimation and correlation methods have been proposed. In this work a new dynamic MI estimation scheme is developed based on system identification techniques. The empirical MI estimation equation proposed in the present study is derived from the 1 ^st -order dynamic models. Effectiveness of the present estimation scheme was illustrated by numerical simulations based on plant operation data including grade change operations in high density polyethylene (HDPE) processes. From the comparisons with other estimation methods it was found that the proposed estimation scheme showed better performance in MI predictions. The virtual sensor model developed based on the estimation scheme was combined with the virtual on-line analyzer (VOA) to give a quality control system to be implemented in the actual HDPE plant. From the application of the present control system, significant reduction of transition time and the amount of off-spec during grade changes was achieved