荧光显示管直丝氧化物阴极有效逸出功的计算

阴极的逸出功是表征阴极发射能力的物理量，求定荧光显示管直丝氧化物阴极有效逸出功时，因其零场发射电流密度难于准确取值，温度无法直接测量，显得困难，须予解决，为此提出了一种计算阴极有产逸出功的办法，对某显示管的发射欠佳和“低温高效”的两种氧化物阴极的有效逸出功进行计算，有效逸出功率是靠测量相关物理量再同计算得出，精度不很高，文中所用办法也不例外，但所得结果能反映阴极发射能力，所需仪器少，是实用方法。     

新型双旋流平焰烧嘴的研制与应用

介绍了一种新型双族流平焰烧嘴的设计思路、结构参数及工业试验结果。其结构特点是每个部件都易装易卸，其煤气旋流器的位置可根据煤气压力变化进行调节，无需稳焰器就可保证煤气压力在较大范围波动时，都可形成稳定的平展火焰。     

Second-order Wagner theory of wave impact

The paper deals with the two-dimensional unsteady problem of the impact of a liquid parabola onto a rigid flat plate at a constant velocity. The liquid is assumed ideal and incompressible and its flow potential. The initial stage of the impact is the main concern in this study. The non-dimensional half-width of the contact region between the impacting liquid and the plate plays the role of a small parameter in this problem. The flow region is subdivided into four parts: (i) the main flow region, the dimension of which is of the order of the contact-region width, (ii) the jet-root region, where the curvature of the free surface is very high and the flow is strongly nonlinear, (iii) the jet region, where the flow is approximately one-dimensional, (iv) the far-field region, where the flow is approximately uniform at the initial stage of impact. A second-order solution in the main flow region has been derived and matched to the first-order inner solution in the jet-root region. The matching conditions provide an estimate of the dimension of the contact region for small time. Pressure distributions in both the main flow region and the inner region are derived. The accuracy of the obtained asymptotic formulae is estimated. The second-order hydrodynamic force acting on the plate is obtained and compared with available experimental data. A fairly good agreement is reported.     

金刚石光电导探测器研制及在软X光测量中的初步应用

介绍了我们自己设计制造的天然Ⅱａ型金刚石光导探测器的结构，原理，制造工艺，实验标定及其在ＩＣＦ实验中软Ｘ光测量中的应用等。     

The statistical modeling of surface roughness in high-speed flat end milling

Surface roughness is one of the most important requirements in machining process. The surface roughness value is a result of the tool wear. When tool wear increase, the surface roughness also increases. The determination of the sufficient cutting parameters is a very important process obtained by means of both minimum surface roughness values and long tool life. The statistical models were developed to predict the surface roughness.This paper presents the development of a statistical model for surface roughness estimation in a high-speed flat end milling process under wet cutting conditions, using machining variables such as spindle speed, feed rate, depth of cut, and step over. First- and second-order models were developed using experimental results of a rotatable central composite design, and assessed by means of various statistical tests. The highest coefficient of correlation (R_adj²) (88%) was obtained with a 10-parameter second-order model. Meanwhile, a time trend was observed in residual values between model predictions and experimental data, reflecting the probable effect of the tool wear on surface roughness. Thus, in order to enhance the estimation capability of the model, another independent variable was included into the model to account for the effect of the tool wear, and the total operating time of the tool was selected as the most suitable variable for this purpose. By inserting this new variable as a linear term into the model, R_adj² was increased to 94% and a good fit was observed between the model predictions and supplementary experimental data.In this study, it was observed that, the order of significance of the main variables is as X₅>X₃>X₄>X₁>X₂ (total machining time, depth of cut, step over, spindle speed and feed rate, respectively).     

平盖开孔的有限元分析及其补强方法的探讨

为了使平盖开孔补强结构更为合理、可靠,使用圆形平板的理论解和有限元分析方法,对不同开孔直径的27个平盖模型进行了应力计算和分析比较,进一步探讨了不同的开孔补强方法。结果表明,对于开孔率小于0.5的平盖开孔补强采用均匀增加平盖厚度的方法,不能解决孔边产生的应力集中问题,难以达到补强的效果;而采用外加补强元件的方法,则应明确其补强范围应在2d范围内。     

直线磁场调制电机推力特性关键参数分析

直线磁场调制电机由于材料成本受行程长度影响较小,适合于长行程应用场合。为获得更好的推力特性,本文从理论研究入手,分析了直线磁场调制电机推力的解析公式,进而确定气隙磁密谐波含量影响推力特性。为了提高气隙磁密的正弦度,电机采用Halbach永磁阵列,相比于传统法向充磁直线磁场调制电机平均推力提高18%,但推力波动率也增大了3.4%。为了尽量降低推力波动,利用有限元法对Halbach永磁体结构、电枢齿靴宽度、调磁块的尺寸和形状等结构参数进行参数化分析与改进设计。最终平均推力为783N,相比于传统法向直线磁场调制电机平均推力提高了44.5%,推力波动率从16.1%降低到8.3%。     

大断面蠕铁缸盖缩松原因分析及防治

对于大断面柴油机气缸盖,通过采用顶置发热冒口,并配合使用冷铁,能最大发挥冒口作用。对于大型单体气缸盖,可采用平组立浇方式,增强顺序凝固作用,进一步缩小缩松风险。     

The form error prediction in side wall machining considering tool deflection

In this research, an effective method for the form error prediction in side wall machining with a flat end mill is suggested. The form error is predicted directly from the tool deflection without surface generation by cutting edge locus with time simulation. The developed model can predict the surface form error accurately about 300 times faster than the previous method. Cutting forces and tool deflection are calculated considering tool geometry, tool setting error and machine tool stiffness. The characteristics and the difference of generated surface shape in up milling and down milling are discussed. The usefulness of the presented method is verified from a set of experiments under various cutting conditions generally used in die and mold manufacturing. This study contributes to real time surface shape estimation and cutting process planning for the improvement of form accuracy.     

Robust flat filtering DSP based control of the boost converter

The article deals with the design and implementation of a flat filter tracking digital controller for a boost dc-dc power converter. A highly perturbed switched boost converter circuit is shown to be efficiently controlled, in a trajectory tracking task for its non-minimum phase output, by means of a suitable linear filter, here addressed as a flat filter. Flat filtering is a natural robust version of generalized proportional integral control (GPIC) by which the effects of arbitrary time varying exogenous disturbances, unknown endogenous nonlinearities and un-modeled dynamics can be jointly attenuated in a conceptually similar fashion to observer-based active disturbance rejection control (ADRC) and algebraic identification based model free control (MFC) but: a) without using extended state observers and b) respecting the original system order in a time-varying simplified model while avoiding algebraic estimation techniques. The proposed control technique based on the TMS320F28335 digital signal processor chip is tested by means of realistic simulations and experimental setup.