Numerical approach to analyze fluid flow in a type C tank for liquefied hydrogen carrier (part 1: Sloshing flow)

The demand for clean energy use has been increasing worldwide, and hydrogen has attracted attention as an alternative energy source. The efficient transport of hydrogen must be established such that hydrogen may be used as an energy source. In this study, we considered the influences of various parameters in the transportation of liquefied hydrogen using type C tanks in shipping vessels. The sloshing and thermal flows were considered in the transportation of liquefied hydrogen, which exists as a cryogenic liquid at ?253 °C. In this study, the sloshing flow was analyzed using a numerical approach. A multiphase sloshing simulation was performed using the volume of fluid method for the observation and analysis of the internal flow. First, a sloshing experiment according to the gas-liquid density ratio performed by other researchers was utilized to verify the simulation technique and investigate the characteristics of liquefied hydrogen. Based on the results of this experiment, a sloshing simulation was then performed for a type C cargo tank for liquefied hydrogen carriers under three different filling level conditions. The sloshing impact pressure inside of the tank was measured via simulation and subjected to statistical analysis. In addition, the influence of sloshing flow on the appendages installed inside of the type C tank (stiffened ring and swash bulkhead) was quantitatively evaluated. In particular, the influence of the sloshing flow inside of the type C tank on the appendages can be utilized as an important indicator at the design stage. Furthermore, if such sloshing impact forces are repeatedly experienced over an extended period of time under cryogenic conditions, the behavior of the tank and appendages must be analyzed in terms of fatigue and brittle failure to ensure the safety of the transportation operation.     

Experimental investigation of gas-liquid flow in a vertical venturi installed downstream of a horizontal blind tee flow conditioner and the flow regime transition

A venturi device is commonly used as an integral part of a multiphase flowmeter (MPFM) in real-time oil-gas production monitoring. Partial flow mixing is required by installing the venturi device vertically downstream of a blind tee pipework that conditions the incoming horizontal gas-liquid flow (for an accurate determination of individual phase fraction and flow rate). To study the flow-mixing effect of the blind tee, high-speed video flow visualization of gas-liquid flows has been performed at blind tee and venturi sections by using a purpose-built transparent test rig over a wide range of superficial liquid velocities (0.3–2.4 m/s) and gas volume fractions (10–95%). There is little ‘homogenization’ effect of the blind tee on the incoming intermittent horizontal flow regimes across the tested flow conditions, with the flow remaining intermittent but becoming more axis-symmetric and predictable in the venturi measurement section. A horizontal (blind tee) to vertical (venturi) flow-pattern transition map is proposed based on gas and liquid mass fluxes (weighted by the Baker parameters). Flow patterns can be identified from the mean and variance of a fast electrical capacitance holdup measured at the venturi throat.     

可节约生产成本的湿处理工艺技术

从传统意义上来讲，针织物及对张力敏感的梭织物的湿处理生产线（包括漂白、染色、柒色后水洗）通常是利用染缸来完成的，而这正是高水耗、高蒸汽消耗和高能源消耗的症结所在，同时带来一些质量问题（如折痕、起毛球和刮印等）。随着现代连续式平幅湿处理线技术的发展，整体生产成本可以下降到最多这50％。介绍了德国欧宝泰克生产的敏感织物连续式平幅湿处理线设备。     

毛/涤纱分散/酸性(媒染)染料一浴法筒子染色工艺

毛/涤纱分散/酸性(媒染)染料一浴法筒子染色工艺,在100℃条件下能满足毛、涤两种纤维同时上染,染色产品具有着色深浓鲜艳,色泽一致,各项牢度符合要求,对纤维无损伤等优点,从而缩短生产时间,降低成本,提高经济效益。     

涤纶超细仿麂皮织物染整实践

介绍了涤纶超细仿麂皮织物的染整加工工艺，重点分析了前处理、染色等关键工序，并给出了具体工艺参数。     

Oxygen transport rate on Rhodococcus erythropolis cultures: Effect on growth and BDS capability

The influence of oxygen transport rate on Rhodococcus erythropolis cultures has been studied in a stirred tank bioreactor under different transport and uptake conditions. Oxygen uptake rate has been measured by applying a modified dynamic method and a kinetic model is proposed, obtaining the kinetic parameter values: specific maintenance and yield coefficients. The volumetric mass transfer coefficients under inert conditions, k_La, and during the bioprocess, K_La, have been determined. The values obtained are different and a biological enhancement factor E, has been considered. These parameters have been predicted by the theoretical model and good agreement with experimental data under the conditions studied has been found. The oxygen limitation has been expressed by a modified dimensionless Damköhler number, Da, the relationship between transport and biological reaction rates. This number decreases with increasing stirrer speed; that is, when mass transport resistance decreases. The efficiency of oxygen utilization can be determined by a film effectiveness factor, η. The effectiveness factor was found to be a strong function of Damköhler number and decrease with increasing Da. Furthermore, oxygen concentration into culture depends on the mass transfer and consumption rates. The theoretical model proposed is able to reasonably predict the evolution of dissolved oxygen concentration with time of cultivation.     

无捻毛巾产品毛羽问题的分析与实践

对无捻毛巾产品毛羽问题进行了分析,对成因进行了初步探索.通过试验,制定了较为有效的改进措施和工艺.无捻毛巾制品的毛羽问题得到改善,并控制在一个较为合理的范围内.     

皮革染色助剂的合理使用对染色效果的影响

研究了皮革工业上广泛使用的一些染色助剂以及我们自主研发的APA匀染增艳剂、DA增深固色剂的合理使用对皮革染色的影响,重点考察了它们的匀染、增深、增艳和固色作用.     

蚕蛹蛋白纤维染色性能的研究

由粘胶和蚕蛹蛋白混纺而成的蚕蛹蛋白纤维，采用双活性基活性染料染色，对染色工艺条件作了重点试验。结果表明，pH值和温度是最大的影响因素，该纤维适宜低温、pH值近中性条件下上染和碱性条件下固色。     

计算机配色技术应用于木材染色初探

介绍了计算机测色配色系统的原理,研究了建立木材染色基础数据库的方法,提出了注意事项,并分析了自动配色过程中产生色差的原因及解决方法。