Performance of BaZrO3/Y2O3 dual-phase refractory applied to TiAl alloy melting

Vacuum induction melting is a potential process for the preparation of TiAl alloys with good homogeneity and low cost. But the crucial problem is a selection of high stability refractory. In this study, a BaZrO₃/Y₂O₃ dual-phase refractory was prepared and its performance for melting TiAl alloys was studied and compared with that of a Y₂O₃ refractory. The results showed the dual-phase refractory consisted of BaZr_1-xY_xO_3-δ and Y₂O₃(ZrO₂), exhibited a thinner interaction layer (30 μm) than the Y₂O₃ refractory (90 μm) after melting the TiAl alloy. Although the TiAl alloys melted in the dual-phase and Y₂O₃ refractory exhibited similar oxygen contamination (<0.1 wt%), the alloy melted in the dual-phase refractory had smaller Y₂O₃ inclusion content and size than that in the Y₂O₃ refractory, indicating that the dual-phase refractory exhibited a better melting performance than the Y₂O₃ refractory. This study provides insights into the process of designing highly stable refractory for melting TiAl alloys.     

Inducing sustained oscillations in feedback-linearizable single-input nonlinear systems

The present paper concerns the induction of stable sustained oscillation in feedback-linearizable single-input affine nonlinear dynamical systems via continuous-time state feedback control. The proposed application-oriented control approach is based on the conception of a state feedback controller that ensures the tracking of a limit cycle characterized in terms of the feedback-linearized system. Boundedness and convergence of the closed-loop trajectories are established following the Lyapunov theoretical framework and applying LaSalle׳s stability principle. The proposed approach is demonstrated with computer-simulated control experiments, showing that it ensures the convergence of the state trajectories of the controlled system to a designed limit cycle and that the methodology can, in principle, be applied to any single input feedback linearizable system.     

汽车稳定杆组织与疲劳性能研究

对28Mn6钢制造的汽车稳定杆，分别采用整体感应加热－整体淬火、连续感应加热淬火两种不同热处理工艺，并进行了台架疲劳寿命试验，采用光学显微镜和扫描电镜，分析了经两种不同热处理工艺处理的稳定杆的金相组织及其早期疲劳断裂的断口形貌，提出，获得细小的高韧性索氏体组织是保证良好疲劳寿命的关键，稳定杆喷丸表面质量，游离铁素体也是影响疲劳性能的重要因素。     

Induction in the Timed Interval Calculus

The Timed Interval Calculus, a timed-trace formalism based on set theory, is introduced. It is extended with an induction law and a unit for concatenation, which facilitates the proof of properties over trace histories. The effectiveness of the extended Timed Interval Calculus is demonstrated via a benchmark case study, the mine pump. Specifically, a safety property relating to the operation of a mine shaft is proved, based on an implementation of the mine pump and assumptions about the environment of the mine.     

基于嵌入式以太网的异步电机矢量控制系统体系结构设计

为了实现异步电机现场控制与上层管理的无缝集成，提出在通用变频器一异步电动机调速系统的基础上，采用基于ARM7TDMI核的微控制器和以太网控制芯片，实现异步电机的网络化控制。详细介绍了该系统的体系结构设计方案。     

测量生产井含水率的一种新方法：—屏蔽式感应法

提出了利用屏蔽式感应线圈测量生产井中油水混合物的混合电导率进而推断含水率的方案,并用几何因子理论对仪器设计参数范围进行了估算。结果表明,使用1～5MHz的工作频率,二次场感应信号可达到μV数量级。从原理上看,该方案能测量高含水率的油水混合物,并且不受金属套管的影响。     

最大熵在感应测井反演中的应用

常规的反演方法是对感应测井资料进行线性反褶积。由于感应测并获得的响应曲线是地层非线性时变滤波的结果,感应测井响应随地层电导率发生非线性变化。本文把熵的概念引入到感应测井反演中。用最大熵方法分别设计出实部信号和虚部信号所对应的反滤波因子,两条反映测井响应随电导率非线性变化的非线性函数也被拟合出来。文章最后用设计出的滤波因子及被拟合出的非线性函数对模拟相量感应测井资料进行了相量反褶积。处理结果表明,围岩效应和趋肤效应基本被消除。本方法与常规的三点反褶积法相比,克服了过聚焦现象,提高了精度。     

会计信息失真现象的博弈分析

在对现实进行合理假定的基础上建立了会计信息失真现象的有限完美信息动态博弈模型，并利用后退归纳法找到了五个满足不同条件的纳什均衡解。通过对均衡条件的分析，找出了导致会计信息失真的治理结构原因和法律制度因素，并提出了建设性的解决措施。     

浅谈变频器供电条件下电动机的温升与对策

随着变频调速技术的蓬勃发展，变频器供电电机的温升问题已引起人们的广泛关注。本文首先讨论了电动机的温升限度；然后结合感应电机温升实验的相关数据分析了变频器供电对电动机温升的影响及其原因；最后从降低发热量和提高散热能力两方面提出缓解电机温升的措施，并指出了实际应用中应注意的问题。     

非织造布印花技术探讨

介绍了应用于非织造布印花的技术及工艺，对非织造布印花时应注意的事项进行了说明。