The phosphorescence emission in undoped lead-halide Cs4PbBr6 single crystals at low temperature

Recently, all-inorganic cesium lead-halide perovskites have shown their promise for light emission applications, due to the excellent optical performance. Herein, we report that the initially nonphosphorescent undoped lead-halide Cs₄PbBr₆ single crystals (SCs) exhibit an ultralong phosphorescence emission under X-ray excitation at low temperatures. It is shown that the dramatic change has been taken place in radioluminescence spectra and the broad-band emission gradually appeared with the decrease of temperature. Below 210 K, the radioluminescence spectra can be deconvoluted into one narrow peak located at 530 nm and two broad peaks centered at 595 nm and 672 nm respectively. Subsequently, the time-dependent radioluminescence spectra in undoped lead-halide Cs₄PbBr₆ SCs were investigated. The ultralong phosphorescence emission can persist over 120 min at 70 K. We consider that ultralong phosphorescence originates from defect-related emission. To the best of our knowledge, our finding is the first time that undoped Cs₄PbBr₆ SCs exhibit the phosphorescence emission, which will offer a paradigm to motivate revolutionary applications on perovskite.     

Effects of the film thickness and poling electric field on photovoltaic performances of (Pb,La)(Zr,Ti)O3 ferroelectric thin film-based devices

The ferroelectric photovoltaic (FPV) effect obtained in inorganic perovskite ferroelectric materials has received much attention because of its large potential in preparing FPV devices with superior stability, high open-circuit voltage (V_oc) and large short-circuit current density (J_sc). In order to obtain suitable thickness for the ferroelectric thin film as light absorption layer, in which, the sunlight can be fully absorbed and the photo-generated electrons and holes are recombined as few as possible, we prepare Pb_0.93La_0.07(Zr_0.6Ti_0.4)_0.9825O₃ (PLZT) ferroelectric thin films with different layer numbers by the sol-gel method and based on these thin films, obtain FPV devices with FTO/PLZT/Au structure. By measuring photovoltaic properties, it is found that the device with 4 layer-PLZT thin film (~300 nm thickness) exhibits the largest V_oc and J_sc and the photovoltaic effect obviously depends on the value and direction of the poling electric field. When the device is applied a negative poling electric field, both the V_oc and J_sc are significantly higher than those of the device applied the positive poling electric field, due to the depolarization field resulting from the remnant polarization in the same direction with the built-in electric field induced by the Schottky barrier, and the higher the negative poling electric field, the larger the V_oc and J_sc. At a -333 kV/cm poling electric field, the FPV device exhibits the most superior photovoltaic properties with a V_oc of as high as 0.73 V and J_sc of as large as 2.11 μA/cm². This work opens a new way for developing ferroelectric photovoltaic devices with good properties.     

Thermal behaviour and phases evolution during the sintering of porous inorganic membranes

Anorthite-based highly porous membranes were successfully produced using calcined oyster shell to enhance the pore network. The calcined oyster shells produce CaO responsible for the crystallisation of gehlenite and anorthite at relatively low temperature. While the crystallisation produced nano and meso size of intergranular pores, vitrification of feldspar is responsible for development of the capillary porosities. The increasing sintering temperature from 1200 °C to 1300 °C implies the increase in average pores radius from 1.2 μm to 14.3 μm due to the formation of spherical pores from vitrification. The combination of different class of porosities in the matrices results in the interconnection with improvement of the permeability of the porous network. Porosity, permeability and chemical stability were improved with 20 wt.% of calcined oyster shell addition allowing the possible development of high strength porous network which is promising for the membranes support and other applications including liquid separation as well as liquid filtration where high pressure is used.     

X-ray diffraction and Raman scattering in SbSI nanocrystals

Lattice structure and rod-like shaped SbSI nanocrystals obtained by ball milling with rod thickness down to 70 nm, as estimated from X-ray diffraction (XRD) and electron microscopy, is similar to that of the bulk crystals. The dependence of the grain size on the milling duration is discussed in view of the chain-like crystalline structure of SbSI. Possible factors, responsible for the observed Raman line broadening, are discussed, scattering by surface phonons being considered the predominant one.     

A new colloidal precursor cooperative conversion route to nanocrystalline quaternary copper sulfide

A novel milk-like Cu-thiourea colloid has been synthesized. Nanocrystalline quaternary copper sulfide Cu₂FeSnS₄ was obtained through the Cu-thiourea colloidal precursor cooperative conversion route at low temperature. The samples were characterized by means of X-ray powder diffraction, transmission electron microscopy, scanning electron microscopy, inductively coupled plasma atomic emission spectroscopy, and X-ray energy dispersive spectroscopy techniques. The reaction details and features were described and discussed.     

The reaction of ceria coatings on mica with H2S: An in-situ X-ray diffraction study

Thin layers of ceria were deposited on the surface of mica platelets in solution. The reaction of such particles with hydrogen sulfide yields a red colored special effect pigment. The ceria layer reacts with H₂S to produce a variety of sulfide and oxysulfide phases. The reaction path discovered in situ by time and temperature resolved X-ray diffraction is CeO₂→CeS₂→C-Ce₂S₃→Ce₁₀S₁₄O. The reaction itself is extremely variable depending on gas flow, heating rates and decomposition atmospheres. Effects on the thin film are recorded by scanning electron microscopy (SEM) and revealed a destruction of the layer once red Ce₁₀S₁₄O was formed. The product layer then reveals the typical nonwetting behaviour of a liquid on a surface.     

无机膜的应用与展望

本文综述了无机膜的发展、制备方法和应用。     

Corrosion of tin in citric acid solution and the effect of some inorganic anions

The corrosion behaviour of tin in different concentrations of citric acid solutions (0.3–1.0 M, pH=1.8) was studied at 30 °C by potentiodynamic technique. The E/I profiles exhibit an active passive behaviour. The active dissolution involves one anodic peak A associated with a dissolution of the metals as Sn(II) species. The passivity is due to the formation of thin film of SnO₂ and or Sn(OH)₄ on the anode surface. The cathodic sweep shows a small peak C related to the reduction of the passive film. The peak current density I_p of peak A increases with increasing both acid concentration and sweep rate.

The effects of adding increasing concentrations of Na₂CrO₄, NaMoO₄, NaNO₃ and NaNO₂ on the corrosion of tin in 0.5 M citric acid at 30 °C were investigated. Both CrO₄²⁻ and MoO₄²⁻ ions inhibit the corrosion of tin and the extent of inhibition enhances with their concentrations. Addition of either NO₃⁻ or NO₂⁻ accelerates the corrosion of tin. NO₃⁻ ions are more aggressive than NO₂⁻ ions.     

新型阳离子聚丙烯酰胺微粒的研究 Ⅱ.含PEO支链阳离子聚丙烯酰胺微粒的絮凝性能

以丙烯酰胺、丙烯酰氧基乙基三甲基氯化铵、聚氧乙烯大单体和N ,N’ -亚甲基双丙烯酰胺为单体 ,进行四元反相微乳液共聚合 ,制备出新型含PEO支链的阳离子微粒絮凝剂。然后用该微粒絮凝剂分别对针叶木纸浆和特种纸白水进行了助留和絮凝性能的研究 ,结果表明 ,本新型微粒具有能单独使用、絮凝效果好和抗剪切性强等优点。