镍代钴矿用硬质合金的新进展

概述了镍代钴矿用硬质合金的国内外进展情况．     

Kinetics of AuSn4 migration in lead-free solders

The relatively fast diffusion of Au atoms in eutectic PbSn matrix is considered one of the contributing factors to the Au embrittlement problem. In this study, we further investigated the Au embrittlement problem in high-Sn solders. Experimentally, Sn3.5Ag (wt.%) spheres with 500-μm diameter were soldered over the Au/Ni soldering pads. It was found that some of the AuSn₄ needles that formed after reflow inside the solder migrated back to the solder/pad interface during thermal aging. However, the migration kinetics in high-Sn solders was slower compared to that in eutectic PbSn. The difference in migration kinetics of AuSn₄ in eutectic PbSn and SnAg was ascribed to the difference in the magnitudes of the Au flux and the Ni flux. In eutectic PbSn, the Au flux was much greater than that of the Ni flux, and the Au and Ni flux were in the same order of magnitude in eutectic SnAg. The relative magnitude of the Au and Ni flux changed in eutectic PbSn and SnAg because the homologous temperatures of PbSn and SnAg were different.     

Syngas production via combined oxy-CO2 reforming of methane over Gd2O3-modified Ni/SiO2 catalysts in a fluidized-bed reactor

In this research, Ni/SiO₂ catalyst was modified with different amount of Gd₂O₃ and characterized with temperature-programmed desorption of CO₂ (CO₂-TPD) and NH₃ (NH₃-TPD), temperature-programmed reduction with H₂ (H₂-TPR) and X-ray diffraction (XRD). It was found that Gd₂O₃-modified Ni/SiO₂ catalysts possessed higher CO₂ adsorption and activation ability due to the formation of surface carbonate species. H₂-TPR and XRD characterizations found that the strong interaction among nickel, Gd₂O₃ and SiO₂ took place, which improved the dispersion of Ni. Gd₂O₃-modified Ni/SiO₂ catalysts exhibited higher activity and stability for the combined oxy-CO₂ reforming of methane in fluidized-bed reactor. The H₂/CO ratio in produced syngas could be controlled via controlling reaction temperature and CO₂/O₂ ratio in feed.     

Effect of Pt Incorporation into Ni/ZrO2–SO 4 = /Al2O3 Catalyst for n-Butane Isomerization

Three Ni/ZrO₂–SO₄⁼/Al₂O₃ catalysts with different concentrations of platinum (0.2, 0.3 and 0.4 wt%) were prepare and tested for n-butane isomerization reaction at 338 K, in absence and in presence of hydrogen. The results shown that, at low temperature, platinum contributes to the olefin or butyl ion formation and the reaction follows a bimolecular pathway. However, when the reaction occurs in the presence of hydrogen, the formation of butyl ions is inhibited. The main feature of platinum addition is the stabilization of the catalytic activity, which is indicated by the slow deactivation constants compared to that of the unpromoted catalyst.     

In situ observation of methoxide hydrogenation on the Ni(111) surface

The surface chemistry of methoxide (CH₃O-) on the Ni(111) surface has been studied in the presence of hydrogen pressures up to 2 Torr. During heating in vacuum methoxide decomposes to H₂ and CO, which desorb at 380 and 445 K, respectively. The CH₃O-decomposition process is rate limited by CH bond breaking and exhibits a strong deuterium kinetic isotope effect in CD₃O-. In the presence of ambient hydrogen pressures of 0.02–2.0 Torr both CH₃O- and CD₃O-are hydrogenated directly to methanol at 310 K. Methoxide is hydrogenated by adsorbed hydrogen, which nearly saturates the surface at these pressures and temperatures.     

预化学镀石英光纤表面电镀镍层的研究

采用电镀法在石英光纤表面化学镀Ni—P涂层上续镀厚镍,重点考察了硫酸镍质量浓度、十二烷基硫酸钠质量浓度和电流密度对镍沉积速率和镀层质量的影响并确定了其最适宜值。将质量浓度为1．5g·L^-1的稀土氧化镧（La2O3）添加入普通瓦特镀液中考察其对电镀效果的影响。用扫描电镜和体视显微镜对镀层的表面形貌进行了表征和分析。结果表明,添加稀土La2O3细化了金属晶粒和提高了镀层致密程度,镀层样品（厚度约为800μm）具有高硬度、强附着力、低电阻、高密度和良好的可焊性等性能。     

Electrochemical and microstructural characterization of cyclic redox behaviour of SOFC anodes

The oxidation of Ni to NiO in solid oxide fuel cell (SOFC) anode will result in large bulk volume change, which may change the interfaces of the two phases in the anode cermet and thus may cause significant performance degradation. The reduction and oxidation (redox) of the Ni/YSZ cermet were studied at 800 ℃. Anodic polarization measurements were performed before and after redox cycles. The anode current density at an overpotential of 100 mV kept decreasing during the whole redox treatment. It decreased from 19.11 to 7.95 mA·cm-2 after two redox cycles. Anode supported unit cell was assembled for cell's discharge measurements. Cell performance declined after each redox cycle. The maximum power density decreased from 126.28 to 40.32 mW·cm-2 . The microstructural changes after redox cycling were recorded using scanning electron microscopy (SEM). The results reveal that after re-oxidation, the Ni gets coarse and has a higher porosity; the nickel network structure turns to be desultory.     

PATTERN RECOGNITION APLLIED TO STABILITY OF FILLED Ti_2Ni PHASES

Pattern recognition method is used for the investigation of stability,region of filled Ti_2Niphases in multi-dimensional bond-parameter space.The filling of C,N and O atoms intoT_6 octahedra consisting of atoms of earhy-transition elements makes the expansion of thestability region of Ti_2Ni phase,and the relative stability of AI_2Cu and MoSi_2 type com-pounds decreases after the introduction of non-metallic elements such as C,N and O.     

Ni-Cr-Fe-Si-B合金涂层及铝青铜基体熔合区组织的研究

采用钨极氩弧焊方法在铝青铜基体上施焊了Ni—Cr-Fe-Si—B合金涂层，并运用金相显微镜、扫描电子显微镜及能谱分析了喷涂层、熔合区及热影响区的组织形貌和成分分布。结果表明，喷焊时，在涂层与基体界面两侧各组元均发生了明显的扩散，Cu、Ni组元间可相互取代，基体融合区组织的基本组成仍为α (α γ2)，但同时也形成了Cu2FeAl7、NiAl3等新相，且融合区组织细小，涂层与基体间为冶金态结合。     

Electroless deposition of Ni on template of halloysite and its magnetic property

Halloysite template, a ceramic substrate, is of a hollow cylindric structure, on which the fine Pd nanoparticles are uniformly formed by the reduction of palldate chloride to initiate electroless deposition. The electroless deposition of Ni is catalyzed by the Pd particles, which results in a uniform layer of Ni-P alloy on halloysite. The alloy is of a nanocrystalline structure, of which the average diameter is about 6 nm. After being heat-treated at 400 ℃, it contains both Ni and Ni12P5 crystal, meanwhile, the Ni crystal gets larger with an average size of 51.9 nm.The content of phosphorous in the Ni layer has a great influence on crystal structure. The metallized halloysite has a higher inherent coercive force, and a much lower saturation magnetization in its as-plated state, while after heattreatment, the inherent coercive force decreases drastically. These magnetic properties have great relationship with the superparamagnetism of Ni nanocrystalline and the stress anisotropy in Ni layer.