25%小偏置碰撞策略及测试评估研究

随着汽车事故的增加,且小重叠碰撞事故死亡率居高不下,小偏置碰撞试验逐渐成为焦点。基于IIHS公布的最新车辆碰撞试验结果,统计超过100余款不同类型的25%小偏置碰撞车辆,建立碰撞转角与碰撞区域的数学模型,将25%小偏置碰撞归结为三种不同的碰撞策略,分别是吸能策略、掠过策略和掠过与吸能策略;并进行试验验证,对三种策略的优缺点进行分析。结果表明,小偏置碰撞试验可运用合理的碰撞策略达到法规要求,对25%小偏置碰撞试验具有一定的参考价值。     

超宽带大功率合成器设计北大核心CSCD

在80 MHz~1 GHz频段,单个功率管输出功率能达到100 W以上,为研制输出功率400 W的功率放大器,文中设计了四路功率合成器。该合成器需要实现功率容量大、工作频带宽、体积小的设计目标。在功率容量方面,文中采用悬置带状线结构,其功率容量远远大于微带线结构;在工作频带方面,采用切比雪夫九节阻抗变换器,将工作带宽拓宽为80 MHz~1 GHz;在体积方面,文中合成器的功率合成部分采用Y型节级联实现四路功率合成,阻抗变换部分采用切比雪夫阻抗变换器进行阻抗变换,该结构相较于磁环巴伦功率合成器,不但具有损耗小、平坦度高的优点,而且通过将阻抗变换器设计成曲折的形状,进一步缩小了合成器体积。仿真与实测结果显示该合成器在80 MHz~1 GHz范围内还具有较高的平坦度,合成效率可达90%以上。     

Feedforward control of the transverse strip profile in hot-dip galvanizing lines

Hot-dip galvanizing is a standard technology to produce coated steel strips. The primary objective of the galvanizing process is to establish a homogeneous zinc layer with a defined thickness. One condition to achieve this objective is a uniform transverse distance between the strip and the gas wiping dies, which blow off excessive liquid zinc. Therefore, a flat strip profile at the gas wiping dies is required. However, strips processed in such plants often exhibit residual curvatures which entail unknown flatness defects of the strip. Such flatness defects cause non-uniform air gaps and hence an inhomogeneous zinc coating thickness. Modern hot-dip galvanizing lines often use electromagnets to control the transverse strip profile near the gas wiping dies. Typically, the control algorithms ensure a flat strip profile at the electromagnets because the sensors for the transverse strip displacement are also located at this position and it is unfeasible to mount displacement sensors directly at the gas wiping dies. This brings along that in general a flatness defect remains at the gas wiping dies, which in turn entails a suboptimal coating.In this paper, a model-based method for a feedforward control of the strip profile at the position of the gas wiping dies is developed. This method is based on a plate model of the axially moving strip that takes into account the flatness defects in the strip. First, an estimator of the flatness defects is developed and validated for various test strips and settings of the plant. Using the validated mathematical model, a simulation study is performed to compare the state-of-the-art control approach (flat strip profile at the electromagnets) with the optimization-based feedforward controller (flat strip profile at the gas wiping dies) proposed in this paper. Moreover, the influence of the distance between the gas wiping dies and the electromagnets is investigated in detail.     

Stress-strain relations in elastoplastic solids with Dugdale-type cracks

Mechanical behavior of a two-dimensional elastoplastic solid with rectilinear cracks is investigated. Plastic strip model is used to reduce plasticity problem to the equivalent linear elasticity formulation. Two realizations of the mixed mode plastic strip model are considered: in-line plastic strips as proposed by Becker and Gross [Int. J. Fract. 37 (1988) 163], and inclined plastic strips of Panasyuk and Savruk [Appl. Mech. Rev. 47 (1994) 151]. The effective mechanical response predictions are based on the procedure presented in Kachanov et al., [Appl. Mech. Rev. 47 (1994) 151]. Stress-strain relations are obtained for parallel and randomly oriented non-interacting cracks. Results are compared with known elastic solutions.     

沥青混合料的使用性能与试验方法分析

沥青混合料的使用性能与试验方法对保证和提高沥青路面的修建质量非常重要。在使用荷载、自然因素对沥青路面作用分析的基础上,对沥青混合料的温度稳定性、耐久性、抗滑性及施工的和易性等方面进行了系统的分析探讨,提出了相关的性能要求与试验评价方法。     

智能化中高压变频器实载试验平台的实现

中、高压变频器产量越来越多，但试验手段大多比较落后，一般采用带电机空转的方法。本文介绍了一个高压变频器试验平台，通过该平台可以对电压等级在3kV～10kV、功率在5000kW以下的变频器进行实载试验。     

基于素性检验思想的不可约多项式判断

论文将Fermat素性检验的思想运用于不可约多项式的判断,给出了一个对于不可约判断问题的Monte Carlo 算法,分析了该算法的计算复杂度问题,并且给出了次数在200以内的检验结果。     

CL－1型缓蚀剂的研制

为了阻缓高含水原油对集输管线的腐蚀，研制了ＣＬ－１型输油管线缓蚀剂。这种缓蚀剂是以两种咪唑啉衍生物与联氨为主要成分的复配药剂，运用于油水共在体系．本文介绍了该剂的室内性能评价和现场试验结果。     

防垢剂BZF－2的研制与应用

桩西油田产出原油综合含水已达６０％－７０％，原用防垢剂ＨＥＤＰ已失去有效抑制集输站结垢的性能。本工作针对结垢最严重的桩５２站的应用，研制了以有机膦化合物和聚氧乙烯醚为主成份的防垢剂ＢＺＦ－２，在室内考察了不同条件下的防垢率、腐蚀性、配伍性等性能，在桩５２站进行了为期４个月的现场试验，加量为１０．３ｍｌ／ｌ、防垢率≥９８．０％，加药设备管线的腐蚀率大大降低。