Electrophoretic deposition of graphene oxide on carbon brush as bioanode for microbial fuel cell operated with real wastewater

Microbial fuel cell (MFC) is a promising technology for simultaneous wastewater treatment and energy harvesting. The properties of the anode material play a critical role in the performance of the MFC. In this study, graphene oxide was prepared by a modified hummer's method. A thin layer of graphene oxide was incorporated on the carbon brush using an electrophoretic technique. The deoxygenated graphene oxide formed on the surface of the carbon brush (RGO-CB) was investigated as a bio-anode in MFC operated with real wastewater. The performance of the MFC using the RGO-CB was compared with that using plain carbon brush anode (PCB). Results showed that electrophoretic deposition of graphene oxide on the surface of carbon brush significantly enhanced the performance of the MFC, where the power density increased more than 10 times (from 33 mWm^?2 to 381 mWm^?2). Although the COD removal was nearly similar for the two MFCs, i.e., with PCB and RGO-CB; the columbic efficiency significantly increased in the case of RGO-CB anode. The improved performance in the case of the modified electrode was related to the role of the graphene in improving the electron transfer from the microorganism to the anode surface, as confirmed from the electrochemical impedance spectroscopy measurements.     

n-Al2O3P/Ni复合刷镀层的组织和摩擦磨损特性

研究了镍基纳米Al2O3复合电刷镀层（n-Al2O3^p/Ni）的组织特征及擦磨损特性，并与快镍刷镀（Ni)进行了比较。结果表明：n-Al2O3^p/Ni复合刷镀层表面粗糙度更小，组织更致密，镀层摩擦系数随镀液中纳米粒子含量增加稍有增大；n-Al2O3在复合刷镀层中弥散分布，与基相良好结合；复合镀的耐磨性能明显优于Ni刷镀层，镀液中n-Al2O3含量为20g/L时，复合刷镀层具有最佳耐磨性能。     

太阳能热水器内表面电刷镀锌

用电刷镀的方法,对尺寸为2000mm×1000mm×0.8mm 的 A_3钢板电刷镀锌保护层;并对影响镀锌层质量的因素进行了充分的研究。     

n-Al2O3/Ni复合镀层的组织与滑动磨损性能研究

用电刷镀技术制得了镍基n-Al2O3复合镀层，并对镀层的滑动磨损性能进行了试验研究。纳米复合镀层的表面形貌比较细腻，镀层中纳米粒子分布均匀，与基质金属结合紧密。镀层显微硬度达到HV700，比快速镍镀层提高约40％。滑动磨损试验结果表明，随着纳米粒子含量的增大，镀层的耐磨性提高，摩擦系数也呈增大趋势；但当镀层中n-Al2O3粒子的超过2.56%(质量分数）时，镀层的耐磨性显著下降。纳米复合镀层的磨损机制以疲劳磨损为主，而快速镍底层以粘着磨损为主。     

直流励磁机电刷打火的常见原因及对策

主要介绍了中铝公司山西分公司自备热电厂6台发电机组的励磁机电刷打火的常见原因的分析和处理方法。     

发电机同轴励磁机电刷火花过大的原因及处理方法

本文对发电机同轴励磁机电刷火花过大的原因进行了分析．并针对这些原因提出了相应的处理办法。对规范励磁机的运行维护有很大的帮助。     

DW型单体液压支柱的大修工艺

老煤矿由于资金紧张 ,外购新柱补充很少。因此 ,现使用的单体液压支柱超期服役的较多 ,急需升井大修 ,以满足各矿采煤工作面的需要。采用校直外圆 ,油缸加衬套的大修方法 ,可满足使用要求。     

表面工程技术在导弹武器装备维修中的应用

本文主要介绍铝/F_(46),协合涂层新技术、复合电刷镀Ni—PTFE新工艺、DJB—823电接触保护剂及三防电子器件绝缘清漆在二炮导弹武器装备维修中的应用。     

Low temperature bonding of LD31 aluminum alloys by electric brush plating Ni and Cu coatings

0Introduction Amongavarietyofbondingtechnologies,vacuum brazinghasbeenwidelyadoptedasareliablemethodfor joiningaluminumcomponents[1],whereintheAl Sialloys systemisrecognizedasthemostpopularfillermetals[2,3]. Althoughasoundjointcanbeachievedforcertainalumi…