Understanding and Modeling the Effect of Surfactants in Enhanced Particle Removal from Surfaces in Aqueous Media

The removal of particulate contamination is a critical issue for many manufacturing processes. It is particularly critical to the electronics industry in which small pieces of microscopic debris remaining after chemical mechanical planarization (cmp) using submicron polishing particles can cause device failure. One way to enhance particle removal following the cmp process is to utilize surfactants. Recent research has shown ways to model the effect of surfactants on enhanced particle removal. However, previous research has not demonstrated the effect of ionic strength on enhanced particle removal associated with surfactant use. Past research has also not shown the combined effects of ionic strength and surfactant concentration on enhanced particle removal using surfactants. This article summarizes the parameters affecting particle removal, and it provides data and analysis on the effect of ionic strength as well as the combined effects of ionic strength and surfactant concentration on particle removal following cmp processing.     

Effect of surfactants on phenol removal by the method of polymerization and precipitation catalysed by Coprinus cinereus peroxidase

The removal of phenol by peroxidase‐catalysed polymerization was examined using Coprinus cinereus peroxidase in the presence of surfactants. The non‐ionic surfactants with poly(oxyethene) residues, Triton X‐100, Triton X‐405 and Tween 20, enhanced the phenol removal efficiency at a level similar to high relative molecular mass poly(ethylene glycol) (relative molecular mass 3000). Although the improvement in the removal efficiency was less than that of Triton X‐100, Span 20, sodium lauryl sulfate (SDS) and lauryl trimethylammonium bromide (DTAB) also enhanced the removal efficiency. The requirement of the enzyme for almost 100% removal of 100 mg dm^?3 phenol decreased to one‐fourth by the addition of 30 mg dm^?3 Triton X‐100. Triton X‐100, Triton X‐405, Tween 20 and DTAB could reactivate the enzyme precipitated with the phenol polymer, leading to the restarting of the phenol removal reaction. Copyright © 2003 Society of Chemical Industry     

Cationic ring-opening polymerization of hexamethylcyclodisilazane: General aspects and tentative mechanisms

The ring-opening polymerization of hexamethylcyclodisilazane (D_2NMe), initiated by methyl triflate in 1,2-dichloroethane, forms in the first, fast kinetic step both linear polymer and cyclic dimer (D_4NMe). Subsequently a slow depolymerization process occurs leading to exclusively cyclotrisilazane (D_3NMe). On the basis of kinetic measurements carried out using an adiabatic calorimetric technique and complementary experiments, mechanisms of both propagation, cyclization and back-biting reactions are proposed. The influence of the reaction temperature was also studied; it is demonstrated that, at low temperature, polymerization does not lead to cyclic oligomer formation. In such conditions, the polymerization presents a ‘living’ character.     

Maghnite‐H+, a solid catalyst for the cationic polymerization of α‐methylstyrene

The polymerization of α‐methylstyrene (AMS) catalyzed by Maghnite‐H⁺ (Mag‐H) was investigated. Mag‐H is a montmorillonite sheet silicate clay, exchanged with protons. It was found that the cationic polymerization of AMS is initiated by Mag‐H at ambient temperature in bulk and in solution. The effect of the amount of Mag‐H, the temperature, and the solvent was studied. The polymerization rate increased with increase in the temperature and the proportion of catalyst, and it was larger in nonpolar solvents. These results indicated the cationic nature of the polymerization. It may be suggested that the polymerization is initiated by proton addition to monomer from Mag‐H. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and characterization of maltose fatty acid monoesters as biosurfactants

Maltose long-chain fatty acid esters (MFAE), esterified at the 6 and 6′ position, were synthesized with stearic, palmitic, myristic, and oleic groups. Synthesis yields were 15–20% based on initial maltose present, and structural confirmation was obtained using plasma desorption mass spectrometry and nuclear magnetic resonance spectroscopy. These surfactants have surface tensions in the range of 34–36 dyn/cm at their critical micelle concentrations (CMC) of approximately 10⁻⁵–10⁻⁶ mol/L. The increased chain lengths have a marked effect, reducing CMC values for MFAE by approximately three orders of magnitude over similar carbohydrate-based dodecyl chain sources. Within chain lengths between 14 and 18 carbons, the rate of change in CMC is significant and decreases with increasing chain length for MFAE. The melting points of MFAE are approximately 40°C, and the heat capacities range from 1.6 to 1.9 J/g·K. These numbers are comparable to those of sucrose esters, indicating their applicability in similar uses. However, because MFAE, unlike sucrose, possess an anomeric carbohydrate carbon position, these surfactants maintain their reducing nature and are susceptible to further derivatization. They are also synthesized from renewable, economical carbohydrates and lipids and may provide an excellent alternative to pertrochemical-derived products.     

脂肪醇聚氧乙烯醚的厌氧与好氧生物降解性

以脂肪醇聚氧乙烯醚(AEO)为目标污染物，在等同条件下做厌氧消化污泥和好氧活性污泥对其生物降解性能的对比实验，得出了同一系列AEO分子中聚氧乙烯基与整个分子的降解难易程度的关系。表明：①污泥会对AEO分子产生吸附一脱附作用而出现假降解率，克服假降解率的干扰是准确测定AEO生物降解性的关键因素；②厌氧和好氧条件下，AEO均可降解，但厌氧降解要稍优于好氧降解；③AEO中聚氧乙烯基的单元数(n)是影响其生物降解的重要因素，相同碳链的直链烷基，生物降解率随n的增加而明显降低。     

Adhesion Effects of Intermediate Layers on the Densification of Ceramic Powders

In the ceramic technology the first step to produce sintered bodies is the manufacturing of powders which then are densified. The adhesion mechanisms between the single particles and the agglomerates produced from them determine the densification process. Starting from theoretical considerations adhesion mechanisms, such as solid bridge formation, adhesive bonding and glide-promoting effects, are discussed in principle. Subsequently, the effects of surface-active substances on the densification behaviour of clay-ceramics and oxide-ceramic bodies are discussed. Further, the evaluation of the action of additives to the powder mixtures on the microstructure of the compacts, such as porsity and texture, leads to a compaction equation which describes the transition from the powder pile to a densified green body.     

Polymer/surfactant interaction—Its relevance to detergent systems

The field of polymer/surfactant interaction is reviewed in this work. Results from two investigative methods,viz., dialysis and surface tension, are discussed, illustrating the main behavioral patterns and outlining the principles of the interactions. Next, aspects of the interaction phenomena that appear to have relevance to detergent formulation are presented. These include solution rheology, solubility control and surface conditioning. Lastly, the importance of surface activity of the polymer itself is stressed, culminating in a discussion of the properties of hydrophobically modified water-soluble polymers (“polymeric surfactants”), both alone and in the presence of conventional surfactants. Based on the Samuel Rosen Memorial Award lecture, given at the AOCS Annual Meeting, Anaheim, CA, April 1993.     

十二烷基苯磺酸钠水溶液聚集性质的研究

用滴体积法测出十二烷基苯磺酸钠（ＳＤＢＳ）稀水溶液的表面张力；然后求出其临界胶束浓度（ＣＭＣ）。同时通过溶液的电导率、吸收光谱以及荧光光谱测定求出其ＣＭＣ。这样测出的ＣＭＣ值为１．２～１．６×１０－３ｍｏｌ／Ｌ，与文献值相符。也研究了部分水解的聚丙烯酰胺（ＰＨＰＡＭ）对ＳＤＢＳ聚集性质的影响；发现ＳＤＢＳ的ＣＭＣ值随ＰＨＰＡＭ的加人而减少并且ＰＨＰＡＭ水溶液的粘度随ＳＤＢＳ的存在而急剧降低（类似盐效应）。这些方法与性质对强化采油（ＥＯＲ）是重要的。