Double emulsion (W/O/W) gel stabilised by polyglycerol polyricinoleate and calcium caseinate as mangiferin carrier: insights on formulation and stability properties

Mangiferin (MGF) is a phenolic compound isolated from mango, but its poor solubility significantly limits its use. In this study, MGF was embedded into the inner aqueous phase of W₁/O/W₂ emulsions. Firstly, the dissolution method of MGF was determined. MGF remained stable in solution with pH 13 at 30 min, and its solubility reached 10 mg mL⁻¹. When the pH of MGF solutions was adjusted from pH 13 to pH 6, MGF did not immediately crystallise, providing sufficient time to construct the MGF-loaded W₁/O/W₂ emulsions. Subsequently, the MGF-loaded W₁/O/W₂ emulsions were constructed using polyglycerol polyricinoleate (PGPR) and calcium caseinate (CAS). The formation and stability of the W₁/O/W₂ emulsions were investigated. The MGF-loaded W₁/O/W₂ emulsions stabilised with 1% PGPR and 1% – 3% CAS exhibited a low viscosity, limited loading capacity, and poor stability. Conversely, the MGF-loaded W₁/O/W₂ emulsions stabilised by 3%PGPR–3%CAS exhibited optimal loading capacity (encapsulation efficiency = 95.31% and loading efficiency = 0.91%) and stability, which was attributed to the fact that high viscosity and gel state retarded the migration of inner aqueous phase. These results indicated that the W₁/O/W₂ emulsions stabilised by PGPR and CAS may be a potential alternative for encapsulating mangiferin.     

Nano fibrillated cellulose-based foam by Pickering emulsion: Preparation,characterizations, and application as dye adsorbent

An ecofriendly and biodegradable porous structure was prepared from drying aqueous foams based on nano fibrillated cellulose (NFC), extracted from softwood pulp by subcritical water/CO₂ treatment (SC-NFC). The primary aim of this work was to use the modified SC-NFC as stabilizer for a water-based Pickering emulsion which upon drying, yielded porous cellulosic materials, a good dye adsorbent. In order to exploit the carboxymethylated SC-NFC (CMSC-NFC, with a degree of substitution of 0.35 and a charge density of 649 μeqv/g) as a stabilizer for water-based Pickering emulsion in subsequent step, an optimized quantity of octyl amine (30 mg/g of SC-NFC) was added to make them partially hydrophobic. A series of dry foam structures were prepared by varying the concentrations of treated CMSC-NFCs and 4 wt% was found to be the optimum concentration to yield foam with high porosity (99%) and low density (0.038 g/cc) along with high compression strength (0.24 MPa), superior to the conventionally extracted NFC. The foams were applied to capture as high as 98% of methylene blue dyes, making them a potential green candidate for treating industrial effluent. In addition, the dye adsorption kinetics and isotherms were found to be well suited with second order kinetics and Langmuir isotherm models.     

Investigation the correlation between chemical structure and swelling,thermal and flocculation properties of carboxymethylcellulose hydrogels

Hydrophilic polymer networks (hydrogels) based on sodium carboxymethylcellulose (NaCMC) and polycarboxylic acids (oxalic, succinic, citric and adipic) as cross-linking agents are synthesized by esterification reaction; one series of NaCMC hydrogels cross-linked with citric acid is prepared with acrylamide and acrylic acid (Aam/Aac) copolymers using the design of semi-interpenetrating polymer networks (semi-IPN), in order to increase their potential application for flocculation purposes. The Infrared spectroscopy (FTIR) of hydrogels confirms the esterification reaction between NaCMC and cross-linking agents. Results of swelling measurements show that citric acid in the amount of 15 wt% gives the hydrogels with the best absorption capacity. The results of Differential scanning calorimetry (DSC) and Thermal gravimetric analysis (TGA) show no significant difference in thermal properties of neat and semi-interpenetrating NaCMC hydrogels. The amorphous nature of hydrogels is confirmed by X-ray diffraction analysis (XRD). The results of flocculation study show that combination of NaCMC network and Aam/Aac copolymer with initial mass ratio of 10/90 creates a theoretical platform for the production of flocculant which could show high efficacy in purifying of water dominated by positively charged particles.     

Material encapsulation in poly(methyl methacrylate) shell: A review

Material encapsulation is a relatively new technique for coating a micro/nanosize particle or droplet with polymeric or inorganic shell. Encapsulation technology has many applications in various fields including drug delivery, cosmetic, agriculture, thermal energy storage, textile, and self-healing polymers. Poly(methyl methacrylate) (PMMA) is widely used as shell material in encapsulation due to its high chemical stability, biocompatibility, nontoxicity, and good mechanical properties. The main approach for micro/nanoencapsulation of materials using PMMA as shell comprises emulsion-based techniques such as emulsion polymerization and solvent evaporation from oil-in-water emulsion. In the present review, we first focus on the encapsulation techniques of liquid materials with PMMA shell by analyzing the effective processing parameters influencing the preparation of PMMA micro/nanocapsules. We then describe the morphology of PMMA capsules in emulsion systems according to thermodynamic relations. The techniques to investigation of mechanical properties of capsule shell and the release mechanisms of core material from PMMA capsules were also investigated. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48039.     

Crystal violet dye sorption and transport in/through biobased PVA cryogel membranes

Cryogels based on poly(vinyl alcohol) [PVA] and three types of bioinsertions such as scleroglucan, cellulose microfibers, and zein, respectively, have been prepared using capacity of PVA to crosslink by repeated freezing–thawing cycles. The effect of the incorporation of biopolymers on the properties of PVA cryogel has been studied by using several techniques such as: scanning electron microscopy, differential scanning calorimetry, and Fourier transform infrared studies. The obtained biobased cryogel membranes were subjected to sorption and to diffusion experiments using Crystal Violet (CV), a dye commonly used in the textile industry and in medicine. Image analysis with CIELAB system was used both to monitor the cryogels loading with CV and to gain insight in the dye state into the gel, in correlation with the bioinsertion type and gels morphology. Dye diffusion but also sorption capacity of the cryogels was found to be closely related to the type of biopolymer. In this article the equilibrium (sorption isotherms) and transport properties (diffusion and permeability coefficients) of CV, in/through physical cross‐linked PVA hydrogel membranes with bioinsertions has been reported. The highest efficiency for the CV removal from aqueous solutions was obtained for the PVA/Scl cryogels. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41838.     

Matrix influence on the piezoelectric properties of piezoelectric ceramic/polymer composite exhibiting particle alignment

This study was addressed to the influence of an electric field strength applied at fabrication process and matrix properties, such as the dielectric constant and the Young's modulus, on “pseudo‐1‐3 piezoelectric ceramic/polymer composite” in order to further enhance the piezoelectricity of that. The pseudo‐1‐3 piezoelectric ceramic/polymer composite consists of linearly ordered piezoelectric ceramic particles in polymer material. Silicone gel, silicone rubber, urethane rubber, and poly‐methyl‐methacrylate, which exhibit different dielectric constants and Young's modulus, were used as matrices to evaluate the matrix influence. The piezoelectricity of the pseudo‐1‐3 piezoelectric ceramic/polymer composite was evaluated using the piezoelectric strain constant d₃₃. The d₃₃ is one of the indices of the piezoelectric properties for piezoelectric materials. As a result, it was confirmed that d₃₃ of the pseudo‐1‐3 piezoelectric ceramic/polymer composite increased with the increase of the electric filed strength applied at fabrication process, though, it reached a constant value at a certain strength value. Further it was confirmed that dielectric constant of the matrix had a small influence on d₃₃ of the pseudo‐1‐3 piezoelectric ceramic/polymer composite, however, in case of matrix of lower Young's modulus, d₃₃ was increase. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41817.     

Influence of HMTA ligand in MMA AGET ATRP emulsion polymerization

Interactions of hexamethylenetetramine ligand in atom transfer radical polymerization initiated by activator generated by electron transfer were studied. Polymerization of methyl methacrylate was done using two-step experimental procedure in 2 L emulsion batch reactor at 50, 60, and 80°C. The selection of reactant ratios was quite challenging for a reactor of this size. Replicate runs were conducted for data reproducibility purpose. Gravimetry method and gel permeation chromatography were used to determine monomer conversion, Mn, and PDI of polymer samples. PMMA produced was also characterized by means of dynamic light scattering, Fourier-transform infrared spectroscopy and nuclear Magnetic Resonance spectroscopy. Results showed high monomer conversion up to 93% and Mn ranging 243–274 kg/mol with PDI from 1.45 to 1.60. Besides, combining HMTA with sodium dodecyl sulfate, an anionic surfactant, a well-controlled polymer with a lower Mn of 201 kg/mol and PDI of 1.56 was obtained in 3 hr reaction time.     

乳化钻井液条件下高温高压气井气体扩散研究

高温高压下甲烷在油里的溶解度大，水包油乳化钻井液中存在油相，钻井作业中钻井液静置期间如起下钻、工具故障抢修等时间过长，储层中的甲烷气体会扩散到井眼里。在钻高含硫化氢及二氧化碳气井时，高温高压条件下天然气更有可能到达与油完全互溶的状态。文章将储层内的水平段井眼的气体扩散区域划分为4个区，外滤饼区、内滤饼区、滤液滞留区、滤液未污染区，根据外滤饼区、内滤饼区、滤液滞留区不同计算参数条件，计算预测了在使用水包油乳化钻井液情况下，储层中天然气通过扩散穿过3个区后，进入储层内井眼段环空导致的环空含气质量浓度变化，对环空内含气质量浓度随扩散时间、含油浓度因素的变化进行了定量计算。用伽略金有限元方法求解，计算表明，气体扩散量随钻井液静置时间延长而增加，水基钻井液加入油后与不加油的钻井液相比增大了气体扩散量。     

改性乳化沥青的发展和应用概况

综述了改性乳化沥青的发展及应用概况,重点讨论了改性乳化沥青的生产、制备工艺、稳定性影响因素,并对国内外改性乳化沥青的应用情况加以概述。     

添加剂对工业齿轮油性能影响的研究

研究了硫化烯烃、磷酸酯胺盐、硫磷酸酯极压抗磨剂,含氮杂环衍生物多功能添加剂和防锈剂等,对工业齿轮油抗乳化性能、极压抗磨性能、防锈性能的影响;以及硫化烯烃、磷酸酯盐极压抗磨剂与含氮杂环衍生物多功能添加剂之间的协和效应。试验结果表明:1.2%~1.6%复合添加剂调制的CKD220工业齿轮油中,磷酸脂盐的正确选用可以提高齿轮油的抗乳化性能、防锈性能和减少防锈剂用量。硫化烯烃与磷酸脂盐、含氮杂环衍生物多功能添加剂的合理组合,可以提高齿轮油的极压抗磨性能和防锈性能,减少添加剂总加剂量。