Effects of ethylene-octene copolymer (POE) on the brittle to ductile transition of high-density polyethylene/POE blends

Three kinds of ethylene-octene copolymers (POE) were melt-blended with high-density polyethylene (PE-HD) in different proportions. Detailed characterizations were conducted to analyze their structural differences of POE and its effects in toughening PE-HD. The higher molecular weight POE can improve the toughness of PE-HD. 60:40 PE-HD/POE is elongated to break up to 700% while impact strength is 84.7 kJ/m² at −30°C, which is 21-fold of PE-HD. In the brittle to ductile transition (BDT) during impact, the fracture mechanism changes from the crazing mode to the shear yield-plastic deformation mode. The BDT temperature decreases as the POE molecular weight and its content increase. The interface strength in tension is estimated to access their effects. The Boltzmann-type models were successfully extended to describe the typical S-shaped curves in BDT of notched impact strength vs POE content or temperature. The supplementary decay model is suggested for the attenuation in toughening. Transition map in impact is proposed to select the use range of composition (c ) and temperature (T ) for high toughness. The curves are converted into 3D graph of T -c -impact strength for illustrating their coupling-separate effects, and further into the contour map of impact strength in T -c space for finding their partial equivalence.     

Failure analysis of a broken tooth

Several days after heart surgery, a patient discovered his upper right canine tooth had broken at the root. Such tooth damage, recognized post-operatively, is usually assumed to be caused by blunt mechanical force from an instrument used by the anesthesiologist during placement of a breathing tube at the start of surgery. In this case, the patient had saved the crown portion of the broken tooth, and it was possible to examine the root fracture characteristics. The curvature and direction of the crack path and natural tooth situation suggested that failure could be described through a cantilever beam model. This was confirmed when a whole extracted sample tooth was embedded and broken by a measured force in a manner consistent with the model. The resulting fracture surface matched that of the patient’s broken canine tooth. However, the high load and force direction necessary to fracture the root was inconsistent with forces applied during the anesthesia procedure. The failure analysis and further investigation indicated tooth clenching on the breathing tube during recovery was the likely cause of fracture. This paper presents an alternate explanation for intubation-related dental injury, demonstrates the practicality of fractographic analysis of biological materials, and introduces a methodology for simulating in vitro tooth settings for mechanical testing.     

Microstructure-related fracture toughness and fatigue crack growth behaviour in toughened, anhydride-cured epoxy resins

Fracture toughness and fatigue crack propagation (FCP) of plain and modified anhydride-cured epoxy resin (EP) were studied at ambient temperature. Liquid carboxyl-terminated acrylonitrile-butadiene (CTBN) and silicon (SI) rubber dispersions were used as tougheners for the EP. The morphology of the modified EP was characterized by dynamic mechanical analysis (DMA) and by scanning electron microscopy (SEM). The fracture toughness, K_c, of the compositions decreased with increasing deformation rate. K_c of the EP was slightly improved by CTBN addition and practically unaffected by incorporation of the SI dispersion when tests were performed at low cross-head speed, v. Both modifiers improved K_c at high v, and also the resistance to FCP, by shifting the curves to higher stress intensity factor ranges, ΔK, by comparison with the plain EP. It was established that both fracture and fatigue performance rely on the compliance, J_R, at the rubbery plateau, and thus on the apparent molecular mass between crosslinks, M_c. The failure mechanisms were less dependent upon the loading mode (fracture, fatigue), but differed basically for the various modifiers. Rubber-induced cavitation and shear yielding of the EP were dominant for CTBN, whereas crack bifurcation and branching controlled the cracking in SI-modified EP. The simultaneous use of both modifiers resulted in a synergistic effect for both the fracture toughness at high deformation rate and the FCP behavior.     

Radiation effects on insulators for superconducting fusion magnets

Fibre-reinforced plastics (FRPs) are candidate materials for the insulation of superconducting magnet coils in future fusion reactors. This paper reports on a test programme performed to assess the mechanical properties of these materials and to obtain information on the damage and fracture mechanisms. Different types of FRPs (epoxies and poly- and bismaleimides as resins; two- and three-dimensional E-, S- or T-glass fabrics as reinforcements) were irradiated at room temperature by 2 MeV electrons and ⁶⁰Co-gamma rays up to 1.8 × 10⁸ Gy and by different reactor spectra up to a neutron fluence of 1 × 10²³ m⁻² (E > 0.1 MeV) at room temperature, 80 K or 5 K. Mechanical tests in tension as well as in the intralaminar crack opening and shear mode were carried out on the irradiated samples at 77 K. After low temperature irradiation, half of the samples were subjected to a warm-up cycle to room temperature before testing at 77 K. Results on the influence of different radiation sources and annealing cycles on the mechanical properties of these materials will be discussed.     

Nondestructive characterization of the mechanical strength of diffusion bonds. II. Application of a quasi-static spring model

It has been shown that the acoustic response of imperfect interfaces may be described by a quasi-static spring model. In the present paper, experimental data on the geometry of the contacts between two diffusion-bonded blocks have been used to determine the spring stiffness of such interfaces which have been correlated with experimentally determined ultrasonic reflection coefficients. The correlation between the theoretical reflection coefficient and the spring stiffness was found to be in excellent agreement with experimentally-observed values, if the disbonds are of infinitesimally small thickness. For disbonds of finite thickness, the agreement is less satisfactory. Reasons for the discrepancy in the latter case are unknown at the present time.     

两相共晶NiAl-9Mo合金的蠕变行为

研究了热等静压态的NiAl-9Mo合金在850-950℃和50-100 MPa下的蠕变行为.在试验应力和温度下,该合金蠕变曲线呈现出较短的减速阶段和较长的稳态蠕变阶段;其稳态蠕变速率可用幂指数蠕变方程来描述,应力指数值为4.75±0.25,表观激活能为 410.5±4.5kJ/mol.加速蠕变阶段蠕变速率的增加是由于裂纹的形成和扩展,且其断裂数据遵循Monkman-Grant规律.蠕变断口呈现出塑性断裂和沿晶蠕变断裂的混合特征,但后者比例较大,同一温度下随着应力的增大,沿晶断裂的比例呈现下降的趋势.     

New high-temperature copper alloys

New high-strength, high-temperature Cu-Ni-Si alloys have been developed using additions of Cr, Zr, and/or Ti. These new alloys remain as precipitation hardenable as the base alloy, but the main strengthening phase may be different than Ni₂Si (e.g., Cr₂Ti). Substantial increases in mechanical strength were observed at both room and high temperature (773 K) when additions of Cr+Zr+Ti and Cr+Zr were made. Industrial testing of these alloys indicated a sevenfold increase in the lifetime of lateral blocks in continuous casting equipment of copper alloys.     

Toughness response of vinylester/epoxy‐based thermosets of interpenetrating network structure as a function of the epoxy resin formulation: Effects of the cyclohexylene linkage

Vinylester/epoxy (VE/EP)‐based thermosets of interpenetrating network (IPN) structures were produced by using a VE resin (bismethacryloxy derivative of a bisphenol A–type EP resin) with aliphatic (Al‐EP) and cycloaliphatic (Cal‐EP) EP resins. Curing of the EP resins occurred either with an aliphatic (Al‐Am) or cycloaliphatic diamine compound (Cal‐Am). Dynamic mechanical thermal analysis (DMTA) and atomic force microscopy (AFM) suggested the presence of an interpenetrating network (IPN) in the resulting thermosets. Fracture toughness (K_c) and fracture energy (G_c) were used as the toughness characterization parameters of the linear elastic fracture mechanics. Unexpectedly high K_c and G_c data were found for the systems containing cyclohexylene units in the EP network, such as VE/Al‐EP+Cal‐Am and VE/Cal‐EP+Al‐Am. This was attributed to the beneficial effects of the conformational changes of the cyclohexylene linkages (chair/boat), which were closely analogous to those in some thermoplastic copolyesters. The failure mode of the VE/EP thermoset combinations was studied in scanning electron microscopy (SEM) and discussed. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2124–2131, 2003     

A comparative investigation of interfacial adhesion behaviour of polyamide based self-reinforced polymer composites by single fibre and multiple fibre pull-out tests

Abstract

Interfacial adhesion of composite materials plays an important role in their mechanical properties and performance. In the present investigation, analysis of the interfacial properties of self-reinforced polyamide composites by using microbond multiple fibre pull-out test is emphasised. Microbond specimens prepared through thermal processing are tested for their interfacial properties by multiple fibre bundle pull-out tests and compared with that of traditional single fibre pull-out test specimens. Multiple fibre pull-out addresses the volume fraction as well as eliminates the possibility of fibre breakage before matrix shear. Higher scatter in the data in the samples is addressed in the present studies. FTIR and Fractographic studies are carried out for deep understanding of the post pull-out interfacial adhesion.     

Investigation of mechanical properties and fatigue life of ECARed AA5083 aluminium alloy

Equal‐channel angular rolling (ECAR) is a continuous severe plastic deformation process. In this process, severe shear strains apply to the sheet. This strain increases the yield or ultimate strength of sheet without significant change in sheet dimension. In this paper, the effect of ECAR process on mechanical properties and fatigue life of manufactured sheets will be studied. Four AA5083 samples have been prepared and annealed for obtaining stress‐free samples. Three samples have been rolled by the ECAR process with one, two and three passes of rolling, respectively. Mechanical tests including tensile test, hardness and axial fatigue tests have been carried out on prepared samples. Fatigue tests have been implemented according to a strain‐based approach with a constant strain ratio equal to 0.75 and 0.5 Hz frequency of loading. All of the tests have been carried out in controlled laboratory conditions. Results show that the ultimate tensile strength of samples increases with increasing the pass of rolling. Also, the maximum elongation of samples decreases. Maximum elongation was 17% in annealed samples, while it decreases to 10% in samples with three passes of rolling. The hardness of samples has been measured, and the results show an increase in hardness for a higher pass of the ECAR process. Fatigue test results show that fatigue life of AA5083 samples decreases in manufactured sheets of the ECAR process. Also, cyclic softening has been observed in the ECARed sample. The fracture surfaces of samples after fatigue test have been observed with a scanning electron microscope. A comparison of fracture surfaces confirms that the crack growth was intergranular in annealed samples while it changes in ECARed samples to transgranular.