Method to Characterize the Air Flow and Water Removal Characteristics During Vacuum Dewatering. Part II—Analysis and Characterization

This is part II of a study reported earlier on a method to characterize the air flow and water removal characteristics during vacuum dewatering. This article presents experimental data and analysis of results from the use of a cyclically actuated vacuum dewatering device for removing moisture from wetted porous materials such as paper with the intermittent application of vacuum and accompanying air flow though the material. Results presented include sheet moisture content as a function of residence time and hence water removal rate under a variety of process conditions. Also, experimental results on air flow through the wet porous structure and hence the role and importance of air flow during vacuum dewatering are presented. Vacuum dewatering process conditions include exit solids content between 11 and 20% solid under applied vacuum conditions of 13.5 to 67.7 kPa (4 to 20 in. Hg). Regression analysis indicated that the exit sheet moisture content exhibited a nonlinear relationship with residence time with exit solids reaching a plateau after a certain residence time. Final moisture content correlated linearly with the average overall flow rate of air through the paper sample and the basis weight of the material.     

我国先进制造技术的现状和发展途径

介绍了现在制造业中面临的问题，通过对问题的分析，提出了发展先进制造前沿技术的见解和在我国发展先进制造技术的途径，同时展望了先进制造技术的发展前景。     

激光辐照制备搪瓷涂层

激光辐照制备的搪瓷涂层表面粗糙,与金属基材结合牢固。一般由 Si,Al,Na,K,B,F,O等元素组成。在激光辐照过程中 K,Na 明显地挥发,从而在涂层中的含量明显减少;Co,Ni,主要分布在界面附近;Fe 元素也由基材进入涂层,呈梯度状分布,在界面过渡区含量很高,在涂层内含量很低。搪瓷涂层的形成与激光辐照参数,特别与激光功率间存在极为密切的关系;只有选用合理的参数,才能制得搪瓷涂层。     

Industrialization of High Performance Sintered NdFeB Magnets

Sintered Nd-Fe-B magnet was manufactured by advanced equipment via a SC (Strip casting) technology.It has integrative performance.     

Synthesis of chemically and structurally modified dicalcium silicate

This paper describes the synthesis of cements, chemically and structurally related to Ca₂SiO₄. Silica was obtained from rice hull after heating at 600 °C. Calcium oxide and small amounts of barium chloride were mixed in order to obtain a final (Ca/Si) or (Ca+Ba)/Si ratio equal to 1.95, 1.90, and 1.80, which is lower than in the conventional cement. The solids were mixed and ultrasonically treated for 1 h with a water/solid ratio of about 20. After drying and grinding, the mixtures were heated up to 1100 °C. It was possible, in some cases, to obtain a cementitious material. These cements are structurally related to β-Ca₂SiO₄ and the lower (Ca+Ba)/Si ratio obtained was 1.95. The initial chemical compositions of these cements are: (Ca_1.83+Ba_0.12)SiO₄ and (Ca_1.79+Ba_0.16)SiO₄. A further lowering in the (Ca+Ba)/Si ratio changes the nature of the silicates.     

聚合反应器制造质量控制要点探讨

聚合反应器是无法检修设备,不允许打开,所以聚合反应器的制造质量必须严格控制,在设备制造过程中,严格按照设计图纸、技术要求及国家现行标准,进行控制设备制造、检验和验收,使制造质量达到规定要求。     

五轴铣削加工中心坐标转换数学模型的建立及应用

首先以 HERMLE C1200 U 为例分析了五轴铣削加工中心的基本结构,然后据此给出了涉及多轴铣削加工中心后置处理角度分配和坐标变换的数学模型,最后介绍了以此数学模型为核心,为UG 软件开发的后置处理软件 UG-HERP1.0的解决方案。     

电机拆线固定装置的制作

针对传统拆线方法劳动强度大及不安全性,制作电机拆线固定装置,为车间的生产提 供安全保障。     

Manufacture of carbon fibers from polyacrylonitrile precursors treated with CoSO4

Free‐radical solution copolymerization of itaconic acid and acrylonitrile was carried out in DMSO using azodiisobutyronitrile as an initiator, changing the feed rate of itaconic acid. The resulting polymerization solution was spun to form polyacrylonitrile (PAN) precursors of carbon fibers. The precursors were treated with a CoSO₄ aqueous solution on‐line. The structure and properties of untreated and treated PAN precursors and the resultant carbon fibers were characterized by SEM and TEM, a stabilization process, etc. It is suggested that CoSO₄ acts as a catalyst in the formation of a ladder structure and reduces the temperature of cyclization, and the carbon fibers developed from treated PAN fibers showed improvement in the tensile strength and the Young's modulus. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 153–158, 2002     

发泡金属的开发、性质及应用(Ⅰ)──发泡金属的制备方法

系统地综述了发泡金属的生产方法，包括铸造法、粉末冶金法、烧结法、沉积法和高压浸透法等。介绍了各种方法的特点及适用范围，指出了它们的优缺点及相应的改进措施，并对今后的发展方向提出了建议。