大直径平底负压容器优化设计

通过对大直径平底负压容器平底板的设计计算,平底板计算厚度很厚。通过分析,提出了对平底板采取加强措施,从而减薄平底板计算厚度的方法。该容器在实际生产过程中性能可靠、稳定,对类似设备设计具有借鉴意义。     

采油树平板闸阀柔性密封圈结构优化设计

为了提高采油树平板闸阀密封圈的密封性能,在泛塞封的基础上,设计一种密封圈本体唇边开有锯齿状凸起的新型柔性密封结构;运用有限元分析方法模拟密封圈的工作状况,分析柔性密封结构特性参数对密封圈密封性能的影响,获得不同柔性密封圈结构参数下密封面间接触应力分布规律,并对新型密封结构进行优化。结果表明:密封面间最大接触应力随唇边锯齿数量、唇边夹角度数的增大而增大,随唇谷夹角度数的增大而减小;新型密封结构选择锯齿数量为3、唇边夹角为20°、唇谷夹角为30°的特性参数时,其最大接触应力比常规Y形密封圈提高了15倍;新型柔性密封结构的密封圈与阀杆、阀盖壁面间接触应力比常规Y形密封圈有显著提高,提高了密封圈的密封性能。     

多业务移动通信系统中的呼叫接入控制

在多业务无线移动通信系统的呼叫接入控制中,不仅要考虑业务之间的优先级,同时也必须考虑切换呼叫的优先级。本文结合可移动边界算法和保护信道策略,提出了一种有效的多业务呼叫接入控制算法。为了方便地分析方案的性能,设计了一个二维的Markov链对方案的性能进行理论上的分析。通过数值分析结果表明,提出的算法同时保证了两种优先级,并提高了系统的性能。1     

无线电车载监测站的信号采集与通讯系统

本系统采用LabVIEW对无线电监测信号进行采集和处理．并开发用户界面。在Delphi平台上运用远程访问服务实现了无线电车载监测站与中心固定站的通讯。LabVIEW主程序对通讯子程序进行调用。     

Dynamics of liquid-filled spacecraft

A method is presented for simulating coupled liquid-solid dynamics. An important example of a coupled liquid-solid system is a satellite carrying fuel. The dynamics of the satellite and the onboard fuel influence each other, which may lead to satellite motion that is uncontrollable. For better understanding of the complex dynamics of coupled systems, a numerical model is developed. The model consists of two parts. The first part that solves the liquid motion is only briefly discussed here. The focus in this paper is on the way in which the dynamics of the liquid and the solid body are coupled. For this, the governing equations are presented in which terms appear that represent the force and torque on the solid body due to the sloshing liquid. The governing equations are rewritten such that the discrete approximation of these equations can be integrated in a stable manner for arbitrary liquid/solid mass ratios. Results are presented demonstrating the stability of the present model. A grid-refinement study and a time-step analysis are performed. Finally, the flat-spin motion of a satellite, partially filled with liquid, that flew in 1992 as part of the Wet Satellite Model experiment is studied. Results from the simulation are compared with the actual flight data.     

Augmentation of boiling heat transfer from horizontal cylinder to liquid by movable particles

This paper presents a series of experimental results on a passive augmentation technique of boiling heat transfer by supplying solid particles in liquid. A cylindrical heater 0.88 mm in diameter is placed in saturated water, in which a lot of mobile particles exist, and the nucleate and film boiling heat transfer characteristics are measured. Particle materials used were alumina, glass, and porous alumina, and the diameter ranged from 0.3 mm to 2.5 mm. Particles are fluidized by the occurrence of boiling without any additive power, and the heat transfer is augmented. The maximum augmentation ratio obtained in this experiment reaches about ten times the heat transfer coefficient obtained in liquid alone. The augmentation ratio is mainly affected by the particle material, diameter, and the height of the particle bed set at no boiling condition. The augmentation mechanism is discussed on the basis of the experimental results. © 2001 Scripta Technica, Heat Trans Asian Res, 31(1): 28–41, 2002     

GPS(NR102K)常见故障与解决方法

GPS硬件由主机和副机两部分组成，本文以Sercel公司生产的NR102K型GPS全球定位系统为例，介绍了其主机和副机在野外施工中的常见故障和解决方法，具有一定的实用性。     

Numerical simulation of typical contact situations of brake friction materials

In the paper, a model typical for contact situations of automotive brakes is established based on the method of movable cellular automata. The processes taking place at local contacts in an automotive brake system are analysed. Based on microscopic and micro-analytical observations, the following contact situations were simulated: (i) a couple of ferritic steel against pearlitic steel, both covered by an oxide layer mixed with graphite nanoparticles and (ii) the same situation but without oxide layers. The results of calculated mean coefficients of friction of the oxide-on-oxide contact correspond well to expected values for a real braking system, whereas steel-on-steel contact are twice as high. This allows one to make some conclusions; for example, oxide formation will take place more quickly than friction layer elimination, and finally this is responsible for the stabilisation of the coefficient of friction.     

哈得逊隆起下石炭统基准面旋回与储集层预测

依据基准面旋回原理和方法,综合利用哈得逊地区的钻井、测井、地震以及地球化学资料,在研究区下石炭统识别出1个Ⅰ型和3个Ⅱ型层序界面,将哈得逊地区下石炭统划分为3个中期基准面旋回：SC1、SC2、SC3,对应于早石炭世海侵的3个海进-海退旋回.SC1旋回以滨岸砂坝沉积为主,而SC2、SC3旋回发育潮坪沉积体系.研究认为,SC1旋回滨岸砂岩及SC2下降半旋回的潮间带薄层砂岩为有利储集砂体,是地层-岩性型油气藏的重点勘探目标.     

小提花横机常见选针出故障的原因及处理方法

介绍了选针片式小提花横机常见选针故障的各种原因，并对不同原因导致的选针故障提出了针对性解决方法。