The effect of segment length on some properties of thermoplastic poly(ester–siloxane)s

A series of novel thermoplastic elastomers, based on poly(dimethylsiloxane) (PDMS) as the soft segment and poly(butylene terephthalate) (PBT) as the hard segment, were synthesized by catalyzed two‐step, melt transesterification reactions of dimethyl terephthalate and methyl esters of carboxypropyl‐terminated poly(dimethylsiloxane)s (M?_n = 550–2170 g mol^?1) with 1,4‐butanediol. The lengths of both the hard and soft segments were varied while the weight ratio of the hard to soft segments in the reaction mixture was maintained constant (57/43). The molecular structure, composition and molecular weights of the poly(ester–siloxane)s were examined by ¹H NMR spectroscopy. The effectiveness of the incorporation of the methyl‐ester‐terminated poly(dimethylsiloxane)s into the copolymer chains was verified by chloroform extraction. The effect of the segment length on the transition temperatures (T_m and T_g) and the thermal and thermo‐oxidative degradation stability, as well as the degree of crystallinity and hardness properties of the synthesized TPESs, were studied. Copyright © 2003 Society of Chemical Industry     

连续法生产冷库板用组合聚醚的研制

针对国内板材厂家提出用连续法生产厚度在150 mm以上冷库板的要求,通过对聚醚体系、催化体系、发泡体系等进行调整,得到了适合于连续法生产厚度在150 mm以上冷库板的组合料,并成功地用于200 mm厚冷库板的连续化生产,未出现烧心开裂、变形等问题.     

Novel polymeric aromatic lithium sulfonylimides as salts for polymer electrolytes

Three new polymeric aromatic lithium sulfonylimides were used as salts in high molecular weight poly(ethylene oxide) (PEO) electrolytes. Their conductivity and electrochemical stability behaviors were investigated. The electrolytes with lithium poly[4,4′‐(hexafluoroisopropylidene)diphenoxy]sulfonylimide (LiPHFIPSI) showed a better conductive performance compared with the other two lithium salts. The best conductivity was obtained for PEO/LiPHFIPSI EO/Li = 16 (1.90 × 10^?4 S/cm at 60°C). Thermal analysis indicated that the salts effectively decreased the crystallinity of PEO. Moreover, the electrolytes also had good electrochemical stability and their oxidative potential was to 5.5 V versus Li/Li⁺. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1802–1805, 2002     

蒙脱土-有机硅复合改性硅烷化聚氨酯密封胶

采用2,4-甲苯二异氰酸酯、聚醚多元醇、蒙脱土、有机硅(α,ω-二羟基聚二甲基硅氧烷)和硅烷偶联剂为原料,制备了有机蒙脱土/聚醚多元醇复合物(OMMT/330N)-有机硅复合改性的硅烷化聚氨酯(SPU)密封胶。通过广角X射线衍射、透射电子显微镜和傅里叶变换红外光谱手段表征了蒙脱土在复合材料中的分散情况,表征结果显示,有机蒙脱土以平均层间距不小于4.12nm的宽分布分散在SPU基体中。同时对密封胶的力学性能进行测试,测试结果表明,经OMMT/330N-有机硅复合改性的SPU密封胶具有性能互补效果,当添加质量分数为5%(基于330N)的OMMT和8%的有机硅时,复合改性的SPU密封胶的拉伸强度和断裂伸长率比纯SPU密封胶提高了65.8%和71.6%。     

聚醚多元醇钻井液研制及应用

以新研制的多功能聚醚多元醇SYP-1为主剂,对聚合物包被剂、防塌剂和降滤失剂进行了优选实验.在此基础上,研制了一种新型的聚醚多元醇钻井液.对聚醚多元醇钻井液的抑制性、流变性、滤失造壁性、润滑性以及对油气层的保护性能进行了室内评价实验,并分析了该钻井液的作用机理.在LN3-6H井和HD4-23H井进行的聚醚多元醇钻井液现场试验表明,在钻进过程中井壁稳定,井径规则,起、下钻畅通,井下安全,测井、下套管及固井作业顺利.室内实验和现场应用表明,聚醚多元醇钻井液具有优良的防塌性和润滑性,能有效地抑制岩屑分散,起到稳定井壁和保护油气层的作用,满足复杂地质条件下钻井的需要.     

Radiation-induced modification of polyurethane with hydroxyethyl methacrylate: blood compatibility

An attempt is made to develop the hydrophilic grafting of polyether urethane urea with hydroxyethyl methacrylate (hema) using⁶⁰Coγ-irradiation for achieving optimum hydrophilic/hydrophobic property needed towards blood compatibility. Contact angle method and platelet adhesion from calf’s blood are used to determine the suitability of these modified surfaces.     

聚醚多元醇中环状齐聚物的去除(续)

(接上期第 2 3页 )3　膜分离Doraietal[16] 通过超滤除去低相对分子质量级份 ,使聚醚多元醇 ,尤其是聚四氢呋喃多元醇 ,具有较窄的分布 (Mw∶Mn=1 .2～ 1 .8)。该方法通过对多分散的熔融聚合物实施物理分级 ,达到降低相对分子质量分布的目的 ,可使最终产物的相对分子质量为 40 0～ 40 0 0 ,分散度为 1 .2～ 1 .8。该方法首先需要准备 1套交叉流动的膜分离系统 ,采用渗透膜或半渗透膜 ,膜的一边是滞留物 ,另一边是超滤液。然后 ,在起始聚合物的熔点以上 ,分解温度以下 ,且温度不大于膜的熔融和分解温度 ,将起始聚合物熔融 ,并流入该系统中…     

二-(4-羟基丁基)四甲基二硅氧烷的合成研究

采用一步法以二甲基二氯硅烷、四氢呋喃和金属镁粉为原料,在碘乙烷和单质碘催化下合成二-(4-羟基丁基)四甲基二硅氧烷。产物温合物减压过滤,以除去镁盐。滤液无需蒸馏提纯,而直接水解,干燥,减压蒸馏,收集71℃/1333Pa馏份。还探讨和优化合成条件:四氢呋喃与二甲基二氯硅烷之摩尔比应大于3.5;Grignard反应停止后应继续加热回流1小时;蒸馏时系统压力为1333Pa。     

两性乳化剂体系对有机硅改性丙烯酸酯乳液合成的影响

采用新型琥珀酸类两性乳化剂(A1)与非离子乳化剂壬基酚聚氧乙烯醚(CA407)复配体系,合成了有机硅γ-甲基丙烯酰氧基丙三甲氧基硅烷(A174)改性的丙烯酸酯乳液。系统研究了两性乳化剂体系与非离子乳化剂复配比例、用量及乳化剂在种子乳液与预乳液中分布比例(R/F)E对乳液聚合及其性能的影响。研究表明:乳化剂配比m(A1)∶m(CA407)=30∶70时,乳液聚合稳定性及抗电解质稳定性较好;乳化剂用量越大,乳胶粒径越小,粒径分布越宽,乳液黏度越大,涂膜吸水率也越大;乳化剂在种子乳液与预乳液中的分布比例主要影响乳液聚合的稳定性。同时通过TEM乳胶粒形态分析及DSC涂膜的玻璃化转变温度分析认为,A174主要在乳液聚合时分布在乳胶粒表面,易水解交联。