玄武岩纤维填料应用于两种混合生长反应器的评价

采用单丝直径微米级的伞状玄武岩纤维(BF)作为填料,将其引入序批式反应器(SBR)和后置缺氧反硝化SBR外聚合物(EPS)含量和扫描电子显微镜形貌图,考察了两种SHBR的污水处理效果。试验结果表明:基于SBR的SHBR的出水COD、氨氮、总氮去除率分别为83.2%、89.9%、86.8%;基于后置缺氧反硝化SBR的SHBR优良,而基于后置缺氧反硝化SBR的SHBR的脱氮效果得到进一步的优化和提升。两种SHBR的BF填料中EPS含量分析结果显示:在好氧环境下,蛋白质(PN)的含量高于多糖(PS)的含量;在缺氧条件下,PS的含量明显高于PN的含量。     

Study of the effect of BDMA catalyst in the epoxy novolac curing process by isothermal DSC

Epoxy novolac/anhydride cure kinetics has been studied by differential scanning calorimetry under isothermal conditions. The system used in this study was an epoxy novolac resin (DEN431), with nadic methyl anhydride as hardener and benzyldimethylamine as accelerator. Kinetic parameters including the reaction order, activation energy and kinetic rate constants, were investigated. The cure reaction was described with the catalyst concentration, and a normalized kinetic model developed for it. It is shown that the cure reaction is dependent on the cure temperature and catalyst concentration, and that it proceeds through an autocatalytic kinetic mechanism. The curing kinetic constants and the cure activation energies were obtained using the Arrhenius kinetic model. A suggested kinetic model with a diffusion term was successfully used to describe and predict the cure kinetics of epoxy novolac resin compositions as a function of the catalyst content and temperature. Copyright © 2003 Society of Chemical Industry     

关于后张预应力混凝土结构优化设计的几个问题

结合UP软件编程实践，本文对后张预应力混凝土结构计算程序中引入优化功能的意义进行了论述，提出了预应力筋与普通钢筋之间的最优搭配关系，优化原点概念及相关影响因素，列出了优化计算程序所应涉及的基本计算内容，并对当前后张预应力混凝土结构设计中的一些观点提出了不同意见。     

红外研究丁羟二异氰酸酯的固化反应动力学

用红外分光光度计研究了端羟基聚丁二烯(HTPBD)与二异氰酸酯的反应动力学,结果表明,NCO与OH的反应为二级动力学反应,由于位阻效应和共轭效应,MDI比TDI的反应活性大得多,前者的反应速率常数大约是后者的10～20倍。反应速率常数及活化能随NCO的过量而有所变化。在NCO过量体系中。TDI-HTPBD体系中有次级反应发生,由于氢键的作用,次级反应为对于氨基甲酸酯基为二级、NCO为一级的三级反应动力学.由于位阻效应,MDI体系很难发生次级反应。     

Optimal control of accelerator concentration for resin transfer molding process

Resin cure following mold filling is an essential element in resin transfer molding. To fabricate a composite part with high dimensional stability and minimize residual stress, uniform resin cure should be achieved. This study considers a three-part resin system composed of epoxy, hardener and accelerator. The cure kinetics can be controlled by the accelerator concentration at the injection gate. A numerical method that can predict degree of cure distribution based on accelerator concentration at the gate was proposed. The degree of cure distribution is obtained by solving the resin flow, heat transfer, accelerator concentration and cure problems sequentially. Utilizing this numerical method, an optimal variation of accelerator concentration during mold filling was sought by solving a constrained optimization problem. The effect of accelerator control on degree of cure distribution was investigated and its validity was examined for two different geometries.     

曙光油田超稠油井套管损坏的机理和防治

超稠油特殊的油藏特点决定了其生产周期短、注汽频繁、出砂、汽窜、超覆现象严重，以及套管质量等因素的影响，套管损坏较为严重。对曙光油田超稠油井套管损坏的规律和机理进行了研究，并从钻井和完井工艺的完善、套管钢级和射孔工艺的选择、采油生产参数的确定、注汽管柱隔热效果的提高、防治砂工艺等方面，对套管损坏提出了预防措施和对策。并对套管损坏井制定了修复再利用方案。     

曼型气柜支柱的安装方法

通过对曼型气柜关键部位之一的基柱的安装和找正过程的分析，表明基柱安装前对基础进行预处理、安装时测量跟踪找正、安装后定位加固，是保证基柱安装精度的三个重要步骤。     

五轴铣削加工中心坐标转换数学模型的建立及应用

首先以 HERMLE C1200 U 为例分析了五轴铣削加工中心的基本结构,然后据此给出了涉及多轴铣削加工中心后置处理角度分配和坐标变换的数学模型,最后介绍了以此数学模型为核心,为UG 软件开发的后置处理软件 UG-HERP1.0的解决方案。     

熔融还原炉内二次燃烧和传热

总结了熔融还原炉内二次燃烧和传热的研究成果，对于转炉采用二次燃烧提高废钢比也有借鉴作用。     

Off-Optimum Cure of Aerospace Epoxy Adhesives

Four epoxy film adhesives used in aircraft manufacture and repair have been examined to establish the effect of deviation from the cure cycle specified by the manufacturer. In addition to the variation of the cure cycle, two surface preparations of the aluminium adherends (chromic acid etch or grit blast followed by silane treatment) were evaluated. Thermal analysis was used to examine the cure envelope of the adhesive, and its extent of cure and glass transition temperature. The adhesive properties were assessed by shear strength (in both single lap joints and in Iosipescu configuration), durability (Boeing wedge test) and chemical resistance to selected aggressive fluids. The sensitivity of the performance of a particular adhesive to offoptimum cure conditions depends on its composition and needs to be determined, not predicted.