Investigation of stress fields for non-standard sized glass plates loaded by ring-on-ring

A ring-on-ring (ROR) test is a prevailing test method for evaluating the equi-biaxial strength of glass materials. However, current ROR test standards limit the strength and size of glass to prevent a nonlinear behavior. In this study, the feasibility of ROR testing for non-standard, high-strength glass, such as tempered or ion-exchanged rectangular glass is investigated. To this end, ROR simulation based on theory and experiment is conducted for thirty non-standard glasses with widths of 100–300 mm and aspect ratios of 1.0–2.0. As a result, the maximum measurable stress was about 215.6 MPa for 100 × 200 mm glass and 481.3 MPa for 300 × 600 mm glass with a 3% deviation, which is well above the strength of regular tempered glass. The main purpose of this work is to understand the range of aspect ratio of horizontal and vertical widths of a glass plate that can be evaluated by the standard ROR test.     

Isolation of the effect of the hairy layer length on the mechanical properties of waterborne coatings

The effect of the acidic hairy layer length on the interdiffusion of polymer between particles and as a consequence on the mechanical properties of the films produced from waterborne coatings has been studied. In order to isolate this effect, latexes with the same particle diameter and molecular weight but stabilized with poly(acrylic acid)-block-poly(butyl acrylate) (PAA-b-PBA) block copolymers of controlled and different lengths were prepared. Tensile strength measurements showed at the macroscopic level that the presence of AA chains in the particle surface reduced the mechanical properties of the films dried at room temperature, being its effect worse the longer the AA chain length. Higher annealing temperatures erased the negative effect of the acidic hairy layer on mechanical properties. The neutralization with NaOH instead of with NH₄OH also led to worse mechanical properties. These macroscopic results were supported by Fluorescence Resonance Energy Transfer (FRET) experiments that showed that at the microscopic level, the extent of interdiffusion occurred slower when the AA chains in the particles surface increased, the annealing temperature was lower and when NaOH was used as neutralizing agent instead of NH₄OH.     

强捻棉纱针织产品的性能研究

通过对强捻棉纱针织产品进行服用性能测试，得出强捻纱织物具有良好的服用性能。     

纳米级BaAl_2O_4微粉的制备和性质

分别用溶胶 -凝胶法、低温固相反应法 ,制得了纳米级BaAl2 O4微粉 ,用电镜观察了其形貌和粒径的大小 ,用X-射线衍射仪进行了物相分析 ,测定了其纯度与晶型 ,讨论了制备方法与粒度大小的相互影响     

环锭细纱机减少成纱毛羽的对策

通过对环锭细纱机成纱毛羽的成因分析 ,提出减少成纱毛羽的措施。     

细旦涤纶50/长绒棉30/丽赛20 7.3 tex高支纱的开发

介绍了细旦涤纶50/长绒棉30/丽赛20纤维的性能,及其混纺纱的生产加工工艺,针对生产中存在的问题,采取了有效的措施,生产的7.3 tex混纺纱线,满足了市场的要求。     

中小企业创业资源的形成机制研究

创业资源是创业的基础,创业过程的规律性和市场配置资源的基础作用影响和决定中小企业创业资源的内在功能和形成方式。对中小企业资源的形成机制进行了分析探讨,并分析了它们之间的内在关系。     

无捻毛巾产品毛羽问题的分析与实践

对无捻毛巾产品毛羽问题进行了分析,对成因进行了初步探索.通过试验,制定了较为有效的改进措施和工艺.无捻毛巾制品的毛羽问题得到改善,并控制在一个较为合理的范围内.     

“新合纤”的研究开发

介绍了“新合纤”研究开发的历史过程以及“新合纤”的特征及其加工方法，讨论了“新合纤”研究开发的现状及其未来。     

蚕蛹蛋白纤维染色性能的研究

由粘胶和蚕蛹蛋白混纺而成的蚕蛹蛋白纤维，采用双活性基活性染料染色，对染色工艺条件作了重点试验。结果表明，pH值和温度是最大的影响因素，该纤维适宜低温、pH值近中性条件下上染和碱性条件下固色。