气力输送在烧结电除尘输灰系统中的应用

针对烧结厂烧结电除尘灰的工况特性，介绍了输送烧结电除尘灰的正压气力输灰系统的特点、组成，还对在调试和试运行过程中遇到的故障进行了分析并制订了解决措施。     

An Experimental Investigation into the Feed Rate Capacity of Rotary Valve and Blow Tank Feeders

Industry widely uses rotary valves and blow tanks for the pneumatic conveying of products, each having their pros and cons depending on the specific application. This article shows the differing results obtained when low-velocity conveying a product through a common pipeline using both a drop-through rotary valve and a bottom-discharge blow tank feeder. A number of issues arise in the rotary valve system, the main one being rotary valve air leakage. A blow tank system, on the other hand, does not leak, as it is an enclosed system. The experimental results show dramatic differences in product throughput. Further exploration leads to a novel modification being made to the rotary valve system in an attempt to increase its capacity. The result of this modification shows a slight increase in output tonnage, but still significantly less than that obtained from the blow tank.     

Effect of tap spacing on observed differential pressure fluctuations in a pneumatic transport line

The standard deviation of differential pressure fluctuations between pressure taps in a 31.7 mm i.d. vertical downer was found to be proportional to the square root of the distance between the taps when measured under otherwise constant conditions. This finding confirms the prediction of a theoretical model based on the Central Limit Theorem of sampling statistics. Although the paper only presents experimental confirmation for downward flow, the theoretical model should be valid for flows in all orientations. Except at very low solids flows, the pressure gradient was found to be positive in the flow direction, indicating that rise in pressure due to static pressure more than compensated for frictional pressure losses.     

An investigation of the unstable region for dense phase conveying in sliding bed flow

For fine powdered materials, capable of being conveyed in dense phase, a conveying region exists in which instability in flow and pipeline blockage can occur if the pressure gradient available is insufficient to maintain a minimum value of solids loading ratio. A reduction in material flow rate can also lead to pipeline blockage in this region. Conveying trials under-taken with cement are used to illustrate the nature of the problem.     

混凝土输送泵液压系统特点分析和性能改进探讨

ＢＳＡ１４０６Ｅ大象泵和ＨＢＴ６０楚天泵均属于电动活塞式大排量、中远程距离的混凝土输送泵，在国内得到广泛地应用。本在分析液压系统原理和功能的基础上，结合使用中出现的问题，从改善性能更加实用和走向国际市场的角度出发，探讨了两种系统的优点和缺陷以及改进方案。     

颗粒状物料气力输送系统中输料管的连接方式

对颗粒状物料的气力输送 ,人们往往只重视所要采用的输送方式 ,而忽视了输料管连接方式的正确选择、施工与安装。输料管连接方式的正确与否 ,直接影响到输送量和物料的品质。详细介绍了常用的几种连接方式 ,分析了它们的优缺点 ,并提出了比较合理的连接方式     

Gravity pipe flow of polymeric bulk solids in pneumatic conveying system

Various physical parameters of gravity pipes such as gravity pipe diameter, the inclination of the gravity pipe, the cone angle, temperature of the discharged material and the rate of air counter flow into the gravity pipe were studied. The results obtained from the pipe diameter and cone angle experiments showed that the mass flow rate was proportional to (D-1.4d)^2.5 and also to θ^-0.5. The results from the pipe inclination experiment showed the existence of an angle of inclination for maximum flow, which was also reported by Wieghardt [Uber einige versuche an stromungen in sand. Ingenieur Archived 20, 109-115]. The air flow experiment also showed that the mass flow rate was inversely proportional to the air counter-flow rate, and strongly influenced by the material properties. Results from the temperature experiment showed that the temperature of the material had slight effect on the mass flow rate for the temperature range that was used in the experiment. Flow visualization images showed formation of solid plugs in the pipe that played a part in influencing the behaviour and mass flow rate of solids in the system.     

基于瞬态熔融理论的新型螺杆研究

通过对挤出机固体输送段物料融解过程的分析，提出了通过在螺槽中垫高固体床，将熔化的熔融物挤进螺槽内侧的熔池中，而在螺槽内侧的熔池保持高度不变，从而使物料和熔融物相对分离，以提高熔化速率以及减少熔融物降解的新型螺杆模型。     

改造本钢265m2烧结机倒料线提高作业率

针对本钢 2× 2 65m2 烧结机成品矿输送流程设计不合理而导致的烧结机频繁停机 ,通过采取合理的改进措施 ,实现了不停机倒料线 ,有效地提高了烧结机作业率和烧结矿产量 ,同时 ,烧结矿质量也有所改善     

三(明)钢烧结厂电除尘灰的气力输送

三钢烧结厂130m^2烧结机电除尘输灰首次采用了气力输送系统。该系统由气源、输送、管路、灰库及控制五部分组成，本文介绍了系统的工作原理及运行调试情况。系统投产后，运行平稳，达到了设计要求。