全文获取类型
收费全文 | 13425篇 |
免费 | 935篇 |
国内免费 | 405篇 |
专业分类
电工技术 | 146篇 |
综合类 | 873篇 |
化学工业 | 1195篇 |
金属工艺 | 4108篇 |
机械仪表 | 3998篇 |
建筑科学 | 92篇 |
矿业工程 | 463篇 |
能源动力 | 159篇 |
轻工业 | 264篇 |
水利工程 | 55篇 |
石油天然气 | 404篇 |
武器工业 | 159篇 |
无线电 | 193篇 |
一般工业技术 | 1712篇 |
冶金工业 | 766篇 |
原子能技术 | 27篇 |
自动化技术 | 151篇 |
出版年
2024年 | 110篇 |
2023年 | 308篇 |
2022年 | 391篇 |
2021年 | 445篇 |
2020年 | 460篇 |
2019年 | 415篇 |
2018年 | 455篇 |
2017年 | 594篇 |
2016年 | 536篇 |
2015年 | 471篇 |
2014年 | 544篇 |
2013年 | 570篇 |
2012年 | 683篇 |
2011年 | 740篇 |
2010年 | 589篇 |
2009年 | 668篇 |
2008年 | 552篇 |
2007年 | 845篇 |
2006年 | 878篇 |
2005年 | 641篇 |
2004年 | 634篇 |
2003年 | 493篇 |
2002年 | 434篇 |
2001年 | 377篇 |
2000年 | 309篇 |
1999年 | 254篇 |
1998年 | 231篇 |
1997年 | 241篇 |
1996年 | 200篇 |
1995年 | 175篇 |
1994年 | 113篇 |
1993年 | 72篇 |
1992年 | 76篇 |
1991年 | 55篇 |
1990年 | 44篇 |
1989年 | 45篇 |
1988年 | 39篇 |
1987年 | 23篇 |
1986年 | 6篇 |
1985年 | 13篇 |
1984年 | 13篇 |
1983年 | 8篇 |
1982年 | 13篇 |
1981年 | 1篇 |
1980年 | 1篇 |
排序方式: 共有10000条查询结果,搜索用时 15 毫秒
1.
2.
本研究针对水泥窑余热发电系统的工作条件,根据耐磨材料的损毁机理,采用高铝矾土、煅烧氧化铝粉、黏土、硅微粉等为原料,以磷酸二氢铝为结合剂,以铝酸钙水泥为促硬剂,通过添加掩蔽剂和优化配料工艺,制备了水泥窑余热发电系统用耐磨材料,并对不同处理温度对耐磨材料的性能影响进行了分析。结果表明增强骨料与基质的结合能力有利于耐磨性的提高,磷酸及磷酸盐与氧化铝之间会随着温度的升高生成不同的磷酸铝相,都能够起到结合作用,比采用水泥结合更有利于提高材料在不同温度下的强度和耐磨性。使用结果表明,制备的耐磨材料施工性能优良,凝结硬化时间适当,强度高,抗冲刷性能好,在水泥窑余热发电系统中取得了良好的使用效果。 相似文献
3.
针对基于容积脉搏波(PPG)提取运动心率时,传统心率提取算法由于运动噪声干扰使测量结果误差大、实时性不好的问题,提出一种抗运动干扰的实时心率提取方法。该方法通过实时小波去噪,同时结合三轴加速度信号(ACC)对运动进行分类训练,计算各运动状态心率增益,对实时心率值进行补偿。实验结果表明,通过与同时采集的ECG信号计算出的实时心率进行对比,绝对误差率仅为1.2%左右。相比传统心率提取算法,该算法具有抗干扰性强,实时准确的特点。 相似文献
4.
In the present work, inter-diffusion of nickel and titanium and formation of Ni-Ti intermetallic compounds on Ti-6Al-4V substrate have been studied. Initially, nickel was electrodeposited on the alloy using a modified Watts bath solution at a current density of 2 A dm?2 for 1?h. The coated specimens were then heat treated for different durations at 750, 800 and 850 °C under argon atmosphere. The effects of temperature and time on the characteristics, hardness and wear resistance of intermetallic phases were investigated. The results showed that a multilayer structure was formed after heat treatment, an outer layer of residual nickel, an area of intermetallic layers with different compositions followed by a solid solution of Ni-Ti. It was also observed that an increase in time or temperature at first led to the formation of thicker intermetallic layers; however, after passing a critical point, the intermetallic layers seem to dissolve into the substrate. Furthermore, the wear rates of the diffusion treated samples were four times lower compared to Ti-6Al-4V alloy when sliding against AISI 52100 hardened steel. 相似文献
5.
6.
Shuangjian Li Xiaoqin Zhao Yulong An Duanduan Liu Huidi Zhou Jianmin Chen 《Ceramics International》2018,44(15):17864-17872
Thermal sprayed ceramic coatings have extensively been used in components to protect them against friction and wear. However, the poor lubricating ability severely limits their application. Herein, yttria-stabilized zirconia (YSZ)/MoS2 composite coatings were successfully fabricated on steel substrate with the combination of thermal spraying technology and hydrothermal reaction. Results show that the synthetic MoS2 powders are composed of numbers of ultra-thin sheets (about 7 ~ 8?nm), and the sheet has obvious lamellar structure. After vacuum impregnation and hydrothermal reaction, numbers of MoS2 powders, look like flowers, generate inside the plasma sprayed YSZ coating. Moreover, the growing point of the MoS2 flower is the intrinsic micro-pores of YSZ coating. The friction and wear tests under high vacuum environment indicate that the composite coating has an extremely long lifetime (>?100,000 cycles) and possesses a low friction coefficient less than 0.1, which is lower by about 0.15 times than that of YSZ coating. Meanwhile, the composite shows an extremely low wear rate (2.30?×?10?7 mm3 N?1 m?1) and causes slight wear damage to the counterpart. The excellent lubricant and wear-resistant ability are attributed to the formation of MoS2 transfer films and the ultra-smooth of the worn surfaces of hybrid coatings. 相似文献
7.
This paper discusses the effects of the grinding-induced cyclic heating on the properties of the hardened layer in a plunge cylindrical grinding process on the high strength steel EN26. It was found that a multi-pass grinding brings about a uniform and continuous hardened layer along the circumference of the cylindrical workpiece. An increase of the number of grinding passes, leads to a thicker layer of hardening, a larger compressive residual stress and a deeper plastic deformation zone. Within the plastic deformation zone, the martensitic grains are refined by the thermo-mechanical loading, giving rise to a hardness of 12.5% higher than that from a conventional martensitic transformation. The coupled effects of heat accumulation and wheel wear in the multi-pass grinding are the main causes for the thickening of the hardened layer. A too small infeed per workpiece revolution would result in insufficient grinding heat, and in turn, bring about an undesirable tempered hardened layer and a reduction of its hardness. 相似文献
8.
Although Mg alloy attracts great attention for engineering applications because of high specific strength and low density, low corrosion resistance limits its extensive use. In this study, Mg–Al–Zn–Mn alloy was treated via a laser cladding process to generate a dense and compact laser cladding layer with solid metallurgical bonding on the substrate for improving corrosion resistance, effectively hindering the corrosion pervasion into Mg alloy. The corrosion current density declined from 103 μA/cm2 for Mg alloy to 13 μA/cm2 for the laser cladding layer in NaCl aqueous solution. Moreover, the laser cladding layer was slightly corroded in comparison with Mg alloy in NaCl aqueous solution. Besides, the microhardness of the cladding layer reached a mean value of 170.5 HV, 3.1 times of Mg alloy (56.8 HV) due to the in situ formation of hardening intermetallic phases. Wear resistance of laser cladding layer was also obviously improved. These results demonstrated that the laser cladding layer obviously enhanced anticorrosion property of Mg alloy for engineering applications. 相似文献
9.
This study aims to evaluate the tribological behaviour of 3Y-TZP/Ta (20 vol%) ceramic-metal composites and 3Y-TZP monolithic ceramic prepared by spark plasma sintering (SPS) against ultrahigh molecular weight polyethylene (UHMWPE). According to the results of pin (UHMWPE)-on-flat wear test under dry conditions, the UHMWPE – 3Y-TZP/Ta system exhibited lower volume loss and friction coefficient than the UHMWPE – monolithic ceramic combination due to the presence of an autolubricating layer that provides sufficient lubrication for reducing the friction. Owing to the lubrication of the liquid media, under wet conditions obtained using simulated body fluid (SBF), similar behaviour is observed in both cases. Additionally, the ceramic and biocomposite materials were subjected to a low temperature degradation (LTD) process (often referred to as “ageing”) to evaluate the changes in the tribological behaviour after this treatment. In this particular case, the wear properties of the UHMWPE-biocomposite system were found to be less influenced by ageing in contrast to the case of the UHMWPE-zirconia monolithic material. In addition to their exceptional mechanical performance, 3Y-TZP/Ta composites also showed high resistance to low temperature degradation and good tribological properties, making them promising candidates for biomedical applications, especially for orthopaedic implants. 相似文献
10.