Three-dimensional and anisotropic numerical analysis of a PEM fuel cell

In this study, the effects of cell temperature and relative humidity on charge transport parameters are numerically analyzed. In order to perform this analysis, three-dimensional and anisotropic numerical models are developed. The numerical models are integrated into the experimental values for anisotropic electrical conductivities, as depending on cell temperature and relative humidity, that were obtained from our previous study. The achieved results indicate that the values of current densities in the in-plane direction increase with increasing cell temperature and relative humidity, while the current densities reach a maximum in the rib regions for both the numerical model at the through-plane direction. The behaviors of electrolyte potentials are similar with changes in the cell temperature and relative humidity. In addition, the cathode electrical potentials in both the in-plane direction and through-plane direction do not change to a considerable amount with increasing cell temperature and relative humidity.     

仙游抽水蓄能电站尾水系统充排水试验

为检查工程质量,查找输水系统可能存在的问题并消除隐患,保障电站安全运行,福建仙游抽水蓄能电站在投产发电前,要对输水发电系统进行充水试验与放空排水试验,在试验过程中监测输水系统的应力、应变与渗漏水情况。本文以尾水系统为例,介绍了试验所应具备的工程条件、工作程序及技术要求、试验成果分析和存在问题处理等。试验表明,仙游抽水蓄能电站尾水系统设计合理,施工质量优良,结构可靠,可供同类工程参考与借鉴。     

乐滩灌区输水隧洞穿合山煤矿采空区处理设计

分析了乐滩灌区工程北干渠溯河隧洞段长约1.06 km穿合山煤矿采空区的地质情况.借鉴高速公路煤矿采空区的成功处理经验,通过科学分析,对采空区变形和区域内覆岩的稳定性做了评价,论述了输水线路穿采空区段采取全充填压力注浆法的工程处理方法.     

黄河龙口水利枢纽坝基岩体钙质充填夹层地质分析与试验研究

龙口水利枢纽坝基岩体主要由奥陶系中统马家沟组(O2m2)灰岩组成,其中发育有多层软弱夹层。作为其中之一的钙质充填夹层,强度虽不很低,但由于处于坝基下的持力层内,间距不大,发育密集,产状平缓,是坝基浅层抗滑稳定的主要控制因素,因此,在大坝抗滑稳定分析时,应进行分析和研究。     

多层梯度层InGaAs（P）InPSAGM雪崩光电二极管

本文报道采用液相外延（ＬＰＥ）生长和传统光刻制管工艺研制出引入多层（三层或三层以上）中间能带隙过渡的吸收区、倍增区分离的ＩｎＧａＡｓ（Ｐ）／ＩｎＰ雪崩光电二极管（简称ＩｎＧａＡｓ（Ｐ）／ＩｎＰＳＡＧＭＡＰＤ），其技术指标为：击穿电压ＶＢ＝４０～９０Ｖ；０．９ＶＢ时的暗电流Ｉｄ最小可小于１０ｎＡ；１．３μｍ时光响应度Ｒｅ＝０．６～０．８Ａ／Ｗ，倍增因子Ｍ≥２０（Ｍｍａｘ＞４０），过剩噪声因子Ｆ≌５和较宽频带响应特性。     

全尾砂高水固化材料在下向充填采矿法中的应用

全尾砂高水固化材料是２０世纪８０年开发出来的矿山新型充填材料，本文简要介绍了全尾砂高固化材料下向进路式充填采矿法的充填工艺技术，并与带钢筋混凝土假顶的下向进路式水硫充填法进行了经济比较。     

发电厂粉煤灰充填矿区塌陷坑方案可行性分析

介绍了煤矿塌陷坑的治理途径和复垦的意义。     

SGM装车机油的研制和应用

中国石化上海高桥分公司炼油厂针对上海通用汽车有限公司(SGM)的别克轿车，先后进行了9986126SGM、9986125SGM装车机油的开发认证工作以及研制油在别克车上的适应性试验。配方研制遵照ACC规范、API基础油互换规则及粘度等级互换规则，各项性能满足技术指标规定的质量要求；同时30000km的高温高速行车试验结果表明，研制油具有较好的抑制氧化增稠能力、优良的高温抗氧化性能、清净分散性能和抗磨损性能，在上海通用别克轿车上取得了良好的使用效果。     

液晶光阀光电导层光吸收系数的研究

用化学气相沉积法制备了液晶光阀中光电导层———非晶硅薄膜,从实验中得出最佳制备工艺的参数取值。给出了用包络线法测量非晶硅薄膜光吸收系数的原理,测量了样品的光吸收系数随波长的变化规律。得到样品在最佳工艺条件下的光吸收系数高于1×103cm-1。     

Thin hard coatings fracture propagation during the impact test

One of the most significant applications of the impact test is to investigate thin hard coatings fatigue properties. Herein the test conditions and duration up to the film damage initiation, are considered in order to determine the critical stresses associated with the coating fatigue strength. Moreover, the subsequent film damage propagation is a significant mechanism as well, since it refers to the ability of the coating to withstand loads after its fatigue damage initiation. In order to describe the film fracture propagation the failed area ratio was introduced and an algorithm to determine this magnitude developed, based on the analysis of imprint scanning electron microscopy graphs. The application of the coating failed area ratio will be demonstrated in various impact test film cases, also with superficial thin layers. The top layers do not affect, in general, the failure initiation of the basic coating. However, according to the obtained results, the superficial films influence the basic coating failure propagation rate during the impact test.