Passive micromixer with baffles distributed on both sides of microchannels based on the Koch fractal principle

Since the beginning of the 21st Century, the development of microfluidic chip technology has been very rapid and has attracted the attention of more and more scholars. As an important part of the microfluidic chip, the performance of the micromixer is critical. The fractal structure in the microchannels helps to improve the mixing performance of the micromixer and improve the mixing efficiency of the micromixer. The research results of other scholars are of great significance to the research of the present paper, which mainly studies the effect of changing the baffle state on the mixing efficiency of the micromixer based on the Koch fractal principle. Through simulation analysis, it was found that the mixing efficiency of the baffles distributed on both sides of the microchannel was higher than the mixing efficiency of the baffles distributed on the microchannel side. When the distance between adjacent baffles was divided into 0.15, 0.25 and 0.35 mm, simulated data suggested that the baffle distance of 0.15 mm was best. Increasing the number of baffles from six to eight groups increased the mixing path of the fluid in the microchannel and improved mixing efficiency. A comparison of mixing efficiencies of the 0°, 15° and 30° baffle angles revealed that very significant improvement in mixing efficiency was obtained at 30°. © 2019 Society of Chemical Industry     

Calorimetric study and thermodynamic description of Ga-Ge-Li liquid alloys

This publication contains the thermodynamic results received by the drop calorimetry method. The experiments were conducted for four different cross sections, at the temperature of 1080 K. The investigated alloys were as follows: (Ga_0.75Li_0.25)_1-xGe_x, (Ge_0.50Li_0.50)_1-xGa_x, (Ga_0.50Li_0.50)_1-xGe_x, (Ga_0.25Li_0.75)_1-xGe_x. The mixing enthalpy changes measured for all four cross sections of the Ga-Ge-Li system are characterized by negative deviations from the ideal solutions. The Muggianu model with the ternary interaction parameters was applied to elaborate the experimental data of the mixing enthalpy change with the use of the optimized thermodynamic parameters of the binary systems available in the literature.     

CFD Modeling of Active Volume Creation in a Non‐Newtonian Fluid Agitated by Submerged Recirculating Jets

Computational fluid dynamics (CFD) models were employed to investigate flow conditions inside a model reactor in which yield stress non‐Newtonian liquid is mobilized using submerged recirculating jets. The simulation results agree well with the experimental results of active volume in the reactor obtained using flow visualization by the authors in a previous study. The models developed are capable of predicting a critical jet velocity (v_c) that determines the extent of active volume obtained due to jet mixing. The v_c values are influenced both by the rheological properties of the liquid and the nozzle orientation. The liquid with higher effective viscosity leads to higher v_c for a downward facing injection nozzle. However, an upward facing injection nozzle along with a downward facing suction nozzle generates enhanced complementary flow fields which overcome the rheological constraints of the liquid and lead to lower v_c.     

乐滩灌区输水隧洞穿合山煤矿采空区处理设计

分析了乐滩灌区工程北干渠溯河隧洞段长约1.06 km穿合山煤矿采空区的地质情况.借鉴高速公路煤矿采空区的成功处理经验,通过科学分析,对采空区变形和区域内覆岩的稳定性做了评价,论述了输水线路穿采空区段采取全充填压力注浆法的工程处理方法.     

PDC钻头水力结构优化设计研究

在PDC钻头工作过程中，钻井液对钻头体表面的冲洗、冷却和润滑是保证钻头正常工作的一个非常重要的条件。对PDC钻头而言，水力结构（主要是中心水眼和冠部水道）设计的重要性尤其突出。以前,对钻头水力系统研究只能通过实验的方法进行,研究周期长、成本高、结构调整不方便，而数值模拟的方法在几年前还不成熟，甚至静态的复杂结构流场问题基本无法解决。为此，在提出PDC钻头水力结构优化设计原则的基础上，对PDC钻头的三维流场进行了数值模拟。模拟中考虑了钻头的喷嘴布置位置、直径、数量以及切削齿对流场的影响。计算结果表明，原设计在喷嘴布置位置和喷射角度上存在不足，以此为基础进行了水力结构的优化设计。文中的研究成果成功地应用在新型钻头水力结构的设计中，研究方法为PDC钻头水力结构优化分析奠定了理论基础。     

双频抽运提高SBS相位共轭保真度

相位共轭保真度是相位共轭镜技术用于强激光系统中的一个重要指标。采用四波混频加强SBS的方法 ,其相干拍频驱动声子场 ,能提高SBS相位共轭保真度。对于双频单池结构 ,使用列阵相机测量激光束能量远场角分布 ,在SBS转换效率最佳时 ,对相干驱动SBS相位共轭保真度进行了实验研究     

高分辨率地震资料处理中的优化速度分析方法

速度分析是地震资料处理过程中的重要一环。速度分析的质量直接影响动静校正,继而影响叠加成像以及偏移归位。针对如何优化速度分析,提出了基于道集资料噪音衰减、道集内相位时差校正、道集优化处理以及速度拾取应用约束等过程的优化速度分析方法。该方法在实际资料处理中取得了很好的效果。     

引入激光回馈的双光束干涉效应的研究

提出了一种引入He-Ne激光回馈的双光束干涉系统,并在理论和实验两方面进行了研究。实验中对系统中的干涉信号及激光器尾光功率变化同时进行探测。发现当干涉仪的主回馈镜移动时,激光器尾光信号是正弦形波形,而干涉仪输出的是以双峰为一个周期的信号,双峰中一峰总是高于另一峰,并且当主回馈镜移动方向改变时,同一周期中两峰出现的顺序也随之改变。对实验现象进行了理论分析,并模拟出干涉信号及激光自身功率的变化曲线。理论分析及模拟结果与实验结果完全吻合。讨论了利用发现的现象进行测量的可行性,所提出的测量方法易于实现。     

Non-equilibrium particle motion in the vicinity of a single blade

The motion of sand particles close to a single moving blade was investigated using Positron Emission Particle Tracking (PEPT) during the period in which the free bed surface profile was evolving to an equilibrium shape. The area affected by the blade was divided into active and inactive regions and these were analysed separately. The characteristic heart-shape of the active region in the plan view was determined. An approximately 10-particle-diameter wide velocity transition zone is found between the two regions. While the tracer particle is in the inactive region moving away from the blade, the time dependence of the axial displacement is well described by a logarithmic relationship. The probability of particle movement towards the centre of the blade was quantified using a “central tendency” index. The calculated central tendency shows maxima at each side of the blade. The separation of the two maxima, which indicates the width of the active region, increases with fill level but is independent of rotational speed.     

关于后张预应力混凝土结构优化设计的几个问题

结合UP软件编程实践，本文对后张预应力混凝土结构计算程序中引入优化功能的意义进行了论述，提出了预应力筋与普通钢筋之间的最优搭配关系，优化原点概念及相关影响因素，列出了优化计算程序所应涉及的基本计算内容，并对当前后张预应力混凝土结构设计中的一些观点提出了不同意见。