减水剂类型对赤泥—矿渣基地聚物注浆材料性能的影响及机理研究

针对赤泥等固体废弃物对环境危害性大且利用率低等问题,以碱激发赤泥-矿渣基地聚物注浆材料为 研究对象,研究了不同掺量的聚羧酸(PA)减水剂、醛酮缩合物(AKC)减水剂和萘系(N)减水剂对材料凝结时间、流动 性及强度等的影响,并通过 XRD、傅里叶红外光谱及 SEM 等设备对减水剂的作用机理进行研究。 结果表明:减水剂增 强了材料的流动性但降低了材料的剪切应力;N 和 PA 减水剂能缩短材料的凝结时间,但 AKC 减水剂会延长材料的凝 结时间;N 和 AKC 减水剂能提高材料的强度,但 PA 减水剂会降低材料的强度;N 减水剂对材料的综合性能提升效果 更加明显,其最优掺量为 0. 7%;减水剂对赤泥-矿渣基地聚物性能提升的作用机理主要是促进地聚合物凝胶的形成。 研究成果为拓展赤泥在工程上的使用途径和效率提供了理论指导。     

Investigation on phase shifting for a 4 K Stirling pulse tube cryocooler with He-3 as working fluid

He-3 is generally recognized for its ability to provide more excellent thermophysical performance than He-4, especially in the 4 K temperature range. However, this was not always the case in our preliminary experiments on a three-stage Stirling-type pulse tube cryocooler (SPTC). Our ongoing studies, as reported in this paper, demonstrate that the different working fluids also affect the performance through their phase shifting capability. This feature has been passed over in large part by researchers considering refrigerant substitution. Unlike previous theoretical analyses that focus primarily on regenerator losses, this report investigates the effects of the working fluid on the phase angle at the cold end in order to quantitatively reveal the relationship between the lowest attainable temperature and the cooling capacity. The analysis agrees well with our experimental results on a three-stage SPTC. While running with the operating parameters optimized for He-3, the lowest temperature of the SPTC decreased from 5.4 K down to 4.03 K. This is the lowest refrigeration temperature ever achieved with a three-stage SPTC.     

Microstructure,tribological behavior and magnetic properties of Fe−Ni−TiO2 composite coatings synthesized via pulse frequency variation

The Fe−Ni−TiO₂ nanocomposite coatings were electrodeposited by pulse frequency variation. The results showed that the nanocomposite with a very dense coating surface and a nanocrystalline structure was produced at higher frequencies. By increasing the pulse frequency from 10 to 500 Hz, the iron and TiO₂ nanoparticles contentswere increased in expense of nickel content. XRD patterns showed that by increasing the frequency to 500 Hz, an enhancement ofBCC phase was observed and the grain size of deposits was reduced to 35 nm. The microhardness and the surface roughness were increased to 647 HV and 125 nm at 500 Hz due to the grain size reduction and higher incorporation of TiO₂ nanoparticles into the Fe−Ni matrix (5.13 wt.%). Moreover, the friction coefficient and wear rate values were decreased by increasing the pulse frequency;while the saturation magnetization and coercivity values of the composite deposits were increased.     

Application of differential evolution for cascaded multilevel VSI with harmonics elimination PWM switching

Harmonic elimination pulse width modulation (HEPWM) method has been widely applied to multilevel voltage source inverter (MVSI) to remove low frequency harmonics from its output voltage. However, the computation of the HEPWM switching angles for MVSI is very challenging due to several constraints, namely angle sequencing, very tight angular spacing and the numerous possibilities of angles distribution ratio. Realizing the potential of Differential Evolution (DE) to handle complex problems, this work proposes its application to solve the HEPWM problem for cascaded MVSI. Its emphasis is on improving the availability of HEPWM for higher output voltage by extending the maximum range of modulation index (M). It also removes the discontinuities in the switching angles and reduces the number of distribution ratio required to obtain the required solution. Compared to the most advanced (similar) work, i.e., 7-level MVSI with seventeen switching angles, DE covers a wider range of M; the maximum achievable M is 2.80. Furthermore, it exhibits very low second order distortion factor (DF₂): for the worst case, the value of DF₂ is 0.0014%. To verify the viability of the proposed algorithm, simulation is carried out and hardware prototype is constructed. Both results show very good agreement with the theoretical prediction.     

激光脉冲编码抗有源干扰效果研究

激光脉冲编码是激光制导武器的抗干扰措施之一。角度欺骗式干扰和高重频干扰是目前半主动激光制导武器的主要有源干扰来源。为研究不同激光脉冲编码方式对激光半主动制导武器抗这两种干扰性能的影响,本文针对敌方激光告警机的识别算法与我方导引头的解码过程,提出自相关函数与归一化互相关函数评价方法,并对目前主要编码方式进行仿真,仿真结果表明:激光脉冲编码的抗角度欺骗式干扰能力受编码序列周期性与脉冲间隔随机性的影响；抗高重频激光干扰能力受编码序列脉冲间隔随机性的影响；LFSR状态码的抗角度欺骗式干扰与抗高重频干扰效果均优于其他编码方式。     

数字化正弦平方脉冲信号

依据正弦平方脉冲的数学方程及其频谱分布，分别导出了与理想和标称视频带宽相对应的正弦平方脉冲的数学表达式及其编程生成方法。实验表明，此法不仅精确，而且便于修改参数，并可直接读人数字电视系统，来测定视频线性响应。     

繁峙县孤山水库帷幕灌浆工程施工

文中叙述了繁峙孤山水库险加固工程帷幕灌浆的施工方案选择、施工过程及工程的质量检查。     

扫描共振频率技术在蓄电池在线修复中的应用

分析了蓄电池组在使用过程受损的原因,介绍了一种蓄电池组在线修复的新技术,即扫描共振频率技术的基本工作原理,并进一步分析、介绍了该在线修复方法所采用的主要新技术和独特的优点。     

一种PD雷达动目标模拟与微波测控系统

介绍了一种基于PC／104总线，具有GPIB程控功能，采用无内部微波源体制，通过在雷达载频上调制多普勒频率模型目标速度信息，延迟雷达发射机触发脉冲模拟目标距离信息并具有微波功率精确定标与衰减功能的PD雷达动目标模拟与微波测控系统。     

水力脉动冲击钻井工具初步研究与试验

掘力脉动冲击钻井是将水力脉冲、机械冲击振动结合为一体提高钻井速度的一种方法，介绍了辽河油田研制的脉动冲击钻井工具的结构、工作原理及现场试验情况。在潜山混合花岗岩、砂岩，硬脆性泥岩等不同地层的现场试验表明：水力脉动工具工作平稳，未出现蹩跳钻现象，也没有出现脱、落、断、掉等问题，主体安全性、可靠性较好；在潜山混舍花岗岩、砂岩、硬脆性泥岩地层机械钻速提高幅度较大，但在部分泥岩地层效果不佳。试验中发现密封圈耐温性差、脉冲腔易磨损等问题，并据此提出了水力脉动冲击工具的下一步研究方向。