减水剂类型对赤泥—矿渣基地聚物注浆材料性能的影响及机理研究

针对赤泥等固体废弃物对环境危害性大且利用率低等问题,以碱激发赤泥-矿渣基地聚物注浆材料为 研究对象,研究了不同掺量的聚羧酸(PA)减水剂、醛酮缩合物(AKC)减水剂和萘系(N)减水剂对材料凝结时间、流动 性及强度等的影响,并通过 XRD、傅里叶红外光谱及 SEM 等设备对减水剂的作用机理进行研究。 结果表明:减水剂增 强了材料的流动性但降低了材料的剪切应力;N 和 PA 减水剂能缩短材料的凝结时间,但 AKC 减水剂会延长材料的凝 结时间;N 和 AKC 减水剂能提高材料的强度,但 PA 减水剂会降低材料的强度;N 减水剂对材料的综合性能提升效果 更加明显,其最优掺量为 0. 7%;减水剂对赤泥-矿渣基地聚物性能提升的作用机理主要是促进地聚合物凝胶的形成。 研究成果为拓展赤泥在工程上的使用途径和效率提供了理论指导。     

Phase formation,structure and properties of light-weight aluminosilicate proppants based on clay-diabase and clay-granite binary mixes

One of the drawbacks of fusible clays is the narrow sintering interval due to a sharp increase in the amount of iron-silicate melt at a temperature of 1000–1100 °C, which hardens in the form of a glass phase upon cooling. This leads to a relatively low mechanical strength of the calcined samples and causes the danger of melting the granular material surface from such clays during the firing process. To increase the strength of samples of fusible clays, the influence of diabase and granitoid rocks was considered. It was found that the strengthening effect of diabase and granitoid rock additives in an amount of 20–50% in a mixture with fusible clay is due to an increase of total content of the crystalline phase (mullite, cristobalite and residual quartz) from 18–20% in clays without additives to 22–28 % - in mixtures with diabase and to 28–34% - with granitoid additives) at a temperature of 1050–1100 °C. This increase is due to the activation of synthesis processes of secondary mullite and crystallization from alkali-rich feldspar melt of amorphous silica, released from the structure of clay minerals. The established influence of the igneous rocks used made it possible to develop compositions and propose process flow sheet for producing aluminosilicate proppants based on fusible clays. The use of granitoid and diabase rocks in an amount of 20–70% with fusible clays produces lightweight aluminosilicate proppants with bulk density of 1.40–1.46 g/cm³ at temperature range of 1050–1100 °C, which can endure destructive pressures up to 34.5–52 MPa.     

Effect of the cultivation mode on red pigments production from Monascus ruber

In submerged cultures performed in chemically defined fermentation medium containing glucose and glutamate, the growth and production of water‐soluble red pigments and citrinin by the filamentous fungus Monascus ruber were studied under various carbon/nitrogen (C/N) ratios. The specific production of the red pigments was optimal at a glucose/glutamate ratio of about 10 and then steadily decreased at higher C/N ratio. In contrast, the production of the mycotoxin increased with increased C/N with an optimum in the range of 30–45. In a fed‐batch mode, it was also found that the production of pigments was not favoured in fed‐batch mode by feeding the medium with glucose while keeping the C/N ratio lower than 10. This low production likely resulted from concurrent high accumulation of L‐malic acid that was reported to inhibit this production. In contrast, this mode of cultivation was rather favourable for the production of the mycotoxin.     

Experimental study on the permeability and self-healing capacity of geosynthetic clay liners in heavy metal solutions

Geosynthetic clay liners (GCLs), which have a very low permeability to water and a considerably high self-healing capacity, are widely used in liner systems of landfills. In this study, a series of experimental tests were carried out under complex conditions on typical commercial GCLs from China. In particular, the effects of pH values and lead ions (Pb²⁺) were tested in addition to other factors. The swelling properties of natural bentonite encapsulated between geotextile components in the GCLs were tested first. The swelling capacity was reduced rapidly at pH values < 3 and concentrations of Pb²⁺ >40 mM. Permeability tests on GCLs with different concentrations of lead ions were then performed by using the self-developed multi-link flexible wall permeameter, and data showed that increases in lead ion concentrations greatly improved the permeability. Finally, self-healing capacity tests were conducted on needle-punched GCLs under different levels of damage. Results showed that the GCLs have a good self-healing capacity with small diameter damage holes (2 mm, close to three times the original aperture), but with a damage aperture larger than 15% of the sample area, the self-healing capacity could not prevent leakage; hence, in certain situations it will be necessary to repair the damage to meet the anti-seepage requirement.     

Effect of marinating ingredients on temperature-induced denaturation of hemoglobin and its relation to red blood spot formation in cooked chicken breast

Red blood spot (RBS) commonly found in cooked chicken breast has caused severe economic loss as it is perceived as a sign of undercooked product. The objectives of this study were to investigate the cause of RBS as related to common ingredients used in marination, based on both chicken breast and isolated chicken hemoglobin (Hb) models. The effect of sodium chloride (NaCl), sodium tripolyphosphate (STPP), and glucose on thermal denaturation of Hb was investigated along with the extent of RBS formation in cooked marinated chicken breast. After vacuum tumbling for 65 min and subsequent storage at 4 °C for 20 hr, STPP and glucose were not absorbed into the center of chicken breast. However, Na⁺ was absorbed after 12 hr storage. The denaturation temperature (T_d) of isolated chicken Hb decreased to 65.8 °C in the presence of 1.5 M NaCl, while that of the control was 69.4 °C. STPP at pH 9 decreased T_d of Hb to 61.4 °C. The alkaline pH induced by STPP destabilized the Hb structure. RBSs were observed at 100% incidence when cooked to core temperatures of 50 and 70 °C for 1 min. RBSs were completely eliminated at core temperature of 85 °C. The ingredients used during marination appeared to have a minimal effect on RBS formation due to their limited absorption into the chicken breast. The cooking temperature is a major factor governing RBSs, as it directly affects the denaturation of Hb.     

Critical state model for structured soil

Structure is an evident determinant for macroscopic behaviors of soils. However, this is not taken into account in most constitutive models, as structure is a rather complex issue in models. For this, it is important to develop and implement simple models that can reflect this important aspect of soil behavior. This paper tried to model structured soils based on well-established concepts, such as critical state and sub-loading. Critical state is the core of the classic Cam Clay model. The sub-loading concept implies adoption of an inner (sub-loading) yield surface, according to specific hardening rules for some internal strain-like state variables. Nakai and co-workers proposed such internal variables for controlling density (ρ) and structure (ω), using a modified stress space, called t_ij. Herein, similar variables are used in the context of the better-known invariants (p and q) of the Cam Clay model. This change requires explicit adoption of a non-associated flow rule for the sub-loading surface. This is accomplished by modifying the dilatancy ratio of the Cam Clay model, as a function of the new internal variables. These modifications are described and implemented under three-dimensional (3D) conditions. The model is then applied to simulating laboratory tests under different stress paths and the results are compared to experiments reported for different types of structured soils. The good agreements show the capacity and potential of the proposed model.     

玉门减压深拔减五线生产微晶蜡的工艺研究及应用

对玉门减压深拔减五线生产微晶蜡的工艺进行了研究并进行了工业应用,生产结果表明:以减压深拔减五线为原料经酮苯脱蜡脱油、白土精制生产微晶蜡,操作过程平稳,酮苯脱蜡脱油过程过滤速度较快,脱蜡油和粗蜡的平均收率可达到78.24%。微晶蜡产品质量符合SH/T 0013-1999标准要求。     

酮苯脱蜡装置用加氢裂化尾油生产优质白油料

加氢裂化尾油经酮苯脱蜡和白土精制工艺可生产高质量润滑油基础油.该基础油具有很好的低温流动性能,且对添加剂感受性好,硫、氮含量低,饱和烃含量高,可以调合中、高档润滑油,制备白油.加氢裂化尾油的综合利用具有明显的经济效益.     

含混合金属的羟基镍铝交联蒙托石的合成

用两种方法——取代法和共聚法合成了一系列羟基镍铝交联蒙托石(GNiAl-CLM和NiAl-CLM),首次利用两种方法,交联前和交联后高温老化处理,对交联蒙托石的热稳定性进行改进。结果表明:取代法合成的羟基镍铝交联蒙托石具有均一的(001)面衍射,底面间距d(001)值均为1.8nm左右,而共聚法合成的羟基镍铝交联蒙托石出现两个(001)面衍射,d(001)值分别为1.8nm和1.55nm;高温处理后,热稳定性得到明显改进,热稳定性可高达700℃以上。