Influence of α′‐/α‐crystal polymorphism on properties of poly(l‐lactic acid)

Poly(l ‐lactic acid) (PLLA) is a biodegradable and biocompatible thermoplastic polyester produced from renewable sources, widely used for biomedical devices, in food packaging and in agriculture. It is a semicrystalline polymer, and as such its properties are strongly affected by the developed semicrystalline morphology. As a function of the crystallization temperature, PLLA can form different crystal modifications, namely α′‐crystals below about 120 °C and α‐crystals at higher temperatures. The α′ modification is therefore of special importance as it may be the preferred polymorph developing at processing‐relevant conditions. It is a metastable modification which typically transforms into the more stable α‐crystals on annealing at elevated temperature. The structure, kinetics of formation and thermodynamics of α′‐ and α‐crystals of PLLA are reviewed in this contribution, together with the effect of α′‐/α‐crystal polymorphism on the properties of PLLA. © 2018 Society of Chemical Industry     

Large domain-wall currents in epitaxial Au/BiFeO3/SrRuO3 thin-film capacitors with modulated oxygen vacancy and wall densities

Large domain wall (DW) conductivity in an insulating ferroelectric plays an important role in the future nanosensors and nonvolatile memories. However, the wall current was usually too small to drive high-speed memory circuits and other agile nanodevices requiring high output-powers. Here, a large domain-wall current of 67.8 μA in a high on/off ratio of ~4460 was observed in an epitaxial Au/BiFeO₃/SrRuO₃ thin-film capacitor with the minimized oxygen vacancy concentration. The studies from read current-write voltage hysteresis loops and piezo-response force microscope images consistently showed remaining of partially unswitched domains after application of an opposite poling voltage that increased domain wall density and wall current greatly. A theoretical model was proposed to explain the large wall current. According to this model, the domain reversal occurs with the appearance of head-to-head and tail-to-tail 180° domain walls (DWs), resulting in the formation of highly conductive wall paths. As the applied voltage increased, the domain-wall number increased to enhance the on-state current, in agreement with the measurements of current-voltage curves. This work paves a way to modulate DW currents within epitaxial Au/BiFeO₃/SrRuO₃ thin-film capacitors through the optimization of both oxygen vacancy and domain wall densities to achieve large output powers of modern domain-wall nanodevices.     

Effects of structural parameters on water film properties of transpiring wall reactor

Corrosion and salt deposition problems severely restrict the industrialization of supercritical water oxidation. Transpiring wall reactor can effectively weaken these two problems by a protective water film. In this work, methanol was selected as organic matter, and the influences of vital structural parameters on water film properties and organic matter removal were studied via numerical simulation. The results indicate that higher than 99% of methanol conversion could be obtained and hardly affected by transpiration water layer, transpiring wall porosity and inner diameter. Increasing layer and porosity reduced reactor center temperature, but inner diameter's influence was lower relatively. Water film temperature reduced but coverage rate raised as layer, porosity, and inner diameter increased. Notably, the whole reactor was in supercritical state and coverage rate was only approximately 85% in the case of one layer. Increasing reactor length affected slightly the volume of the upper supercritical zone but enlarged the subcritical zone.     

Mechanism of smoke suppression by melamine in rigid polyurethane foam

The smoke suppression of rigid polyurethane foam (RPUF) modified by melamine was investigated based on three sections: the condensed phase, the carbon layer, and the gas phase. In the condensed phase, the results of thermogravimetry, X‐ray photoelectron spectroscopy (XPS) N1S spectrum, and Fourier transform infrared spectroscopy indicated that melamine could suppress the degradation of RPUF by reacting with the aromatic hydrocarbons. It also reduced the smoke generation because the volatilizable aromatic hydrocarbons were the principal smoke precursors in a fire. In the carbon layer, the decrease from 38.50% to 24.76% of the inner layer oxygen content identified by XPS full‐spectrum and C1S spectrum indicated that melamine could prevent oxygen from transferring into the inner foam by the formation of an enhanced surface carbon layer, and the enhanced carbon layer could also block the release of smoke precursors. In the gas phase, the content of total aromatic hydrocarbons declined to 59.12% according to pyrolysis gaseous chromatography mass spectroscopy and indicated that melamine could reduce the smoke precursors. The results of smoke density chamber and cone calorimeter tests revealed that the addition of the melamine could decrease the smoke density of burning RPUF. Copyright © 2014 John Wiley & Sons, Ltd.     

墙体裂缝的成因及防治

介绍了墙体裂缝的种类，从地基不均匀下沉、温度变化等方面分析了引起墙体裂缝的原因，介绍了墙体裂缝的预防措施和治理措施，以有效控制墙体裂缝的危害程度。     

谐波齿轮机构在商业表格印刷机中的应用

从商业表格印刷机特殊要求出发，以某一具体机型的传动系统为例，提出采用谐波齿轮机构解决纵向套准的问题。并且分析研究了谐波齿轮机构的工作原理及其在商业表格印刷机中的使用。     

浅谈无缝钢管的壁厚偏差

通过探讨、分析无缝钢管壁厚偏差产生的原因，提出了改善钢管壁厚偏差的一些措施，并结合实际生产，得出了比较满意的结果。     

DIRECT RESONANCE OF TURBULENT BOUNDARY LAVER OVER COMPLIANT WALLS

１．　ＩＮＴＲＯＤＵＣＴＩＯＮＴｈｅｍａｉｎｇｏａｌｏｆｔｈｉｓｐａｐｅｒｉｓｔｏｅｘｐｌｏｒｅｔｈｅｐｏｓｓｉｂｉｌｉｔｙｔｏｌｅａｒｎｍｏｒｅａｂｏｕｔｔｈｅｍｅｃｈａｎｉｓｍｏｆｔｕｒｂｕｌｅｎｔｂｏｕｎｄａｒｙｌａｙｅｒｆｌｏｗｉｎｔｅｒａｃｔｉｏｎｓａｎｄｉｔｓｅｆｆｅｃｔｓｏｎｃｏｍｐｌｉａｎｔｗａｌｌｐｅｒｆｏｒｍａｎｃｅ．Ｔｈｅｒｅａｒｅｃｅｒｔａｉｎｐｒｅｒｅｑｕｉｓｉｔｅｃｏｎｄｉｔｉｏｎｓｔｏｆｕｒｔｈｅｒｔｈｅｓｔｕｄｙｏｎｔｈｅｍｅｃｈａｎｉｓｍ，ｉ．ｅ．ｔｈｅｃｏ…