排序方式: 共有38条查询结果,搜索用时 15 毫秒
1.
针对水库重力式大坝加高加固问题进行试验研究,对后帮式、前帮式、外包式以及戴帽式加高方式建立实验模型评价新旧混凝土结合面的粘结性能。抗折强度试验和微观电镜试验结果表明,四种类型的加高方式,外包式的结合面最大,抗折强度最高,粘结性能最强。采用水泥砂浆处理后增多了结合面的纤维状C-S-H凝胶,增强了新旧混凝土之间的粘结性能,合理的加固方式加上结合面处理有利于提高坝体的安全性能。 相似文献
2.
3.
4.
5.
6.
高耐磨药芯焊丝堆焊组织及基体选择 总被引:1,自引:0,他引:1
制备了高铬铸铁型自保护药芯焊丝,并采用此焊丝分别在 Y-Ni4 铸铁、65Mn钢、40Cr 钢和灰口铸铁基体上进行堆焊.对不同堆焊试样进行硬度测试,对堆焊金属及其结合部位进行显微组织及断口形貌观察.结果表明,堆焊金属硬度在 60HRC 以上,断裂方式均为解理断裂.65Mn 钢堆焊试样熔合较好,且基本无裂纹,可在受冲击载荷较大的条件下使用;Y-Ni4 铸铁堆焊试样熔合良好,但在热影响区存在裂纹,应在冲击载荷较小或不受冲击载荷条件下使用;40Cr 和灰铸铁堆焊试样熔合不好,熔合区存在许多缺陷,不宜作为耐磨堆焊基体材料.Abstract: Four matrix materials, Y-Ni4 cast iron, 65Mn steel, 40Cr steel and grey cast iron, were hardfaced by the high chromium cast iron of self-shielded flux-cored wire separately. The hardness of different hardfacing specimens was measured, and the microstructures, fracture morphologies and the binding sites of different hardfacing specimens were observed. The results show that the hardness of the hardfacing metal is over 60 HRC and the fracture is of cleavage type. The fusion zones of 65Mn and Y-Ni4 hardfacing metal are good ones. However, the cracks can be observed in the heat-affected zone of Y-Ni4 hardfacing specimen. Therefore, the hardfacing metal of 65Mn steel is suitable for the condition of high stress wear and Y-Ni4 cast iron is suitable for the lower one. Besides, there are many defects in the fusion zone of 40Cr and grey cast iron hardfacing specimens, which are not suitable for the wear resistant matrix materials. 相似文献
7.
8.
针对铁路用锻钢支撑座预锻上模左右型腔结合部反复断裂的问题,通过建立塑性有限元和结构有限元分析模型,分析了造成模具断裂的3个关键因素,即左右型腔结合部高度、坯料的定位及摩擦润滑条件。分析发现,随着结合部高度的降低,模具等效应力显著下降,抗失稳的能力明显增强;而随着型腔结合部位高度的增加,模具应力也随之增加,但材料利用率会有所提高。另外,通过对坯料摆放位置的分析,找出了坯料摆放偏离模具中心距离对模具应力的影响规律,其合理取值范围为[0mm,4mm],最大程度的降低了侧向力的影响。同时发现,在模具表面粗糙度及润滑状况不良的情况下,致使模具应力增加,将加剧模具失效。论文优化并确定了模具的结构形状,通过生产试制,验证了上述分析的正确性。 相似文献
9.
10.