洼60-H26水平井套铣打捞技术

洼60-H26井是一口中曲率水平井,设计井深1 922 m,由于地面条件的限制,设计采用三维井眼轨道。该井水平段在钻至井深1 801 m时,发生卡钻事故。在卡钻事故处理过程中,采用测卡、爆炸松扣技术取出上部钻具后,应用了不同规格的套铣管对被卡钻具进行套铣,采用间歇式套铣方式实现了大斜度井段(45°-90°)的安全套铣,采用短套铣管完成了时水平井段内φ215．0 mm稳定器的套铣,采用φ228．6 mm套铣管成功套铣水平井段被卡LWD仪器,最后通过震击器震击成功解卡。详细介绍了洼60-H26水平井卡钻事故的处理过程,分析了在水平段处理卡钻事故的难点。该井处理卡钻事故的经验,对以后水平井施工中处理井下事故、打捞贵重仪器具有借鉴价值。     

Development of Solar Drying

Importance of Solar Drying is increasing worldwide, especially in areas where the use of the abundant, renewable and clean solar energy is essentially advantageous. In the developing countries and in rural areas the traditional open-air drying methods should be substituted by the more effective and more economic solar drying technologies.

R&D needs should be considered in the basic research and experimental fields; in performance measurement; in the modelling-simulation-design and testing. The international co-operation of experts should be improved and more efforts would be needed in the policy and in the public information.     

Granular Reasoning Using Zooming In & Out: Part 2. Aristotle's Categorical Syllogism

The concept of granular computing is applied to Aristotle's categorical syllogism. Such kind of reasoning is called granular reasoning in this paper. For the purpose, two operations called zooming in & out are introduced to reconstruct granules of possible worlds.     

An illustration of verification and validation in the modelling phase of KBS development

Reliability has become a key factor in KBS development. For this reason, it has been suggested that verification and validation (V&V) should become an integrated part of activities throughout the whole KBS development cycle. In this paper, it will be illustrated how the PROLOGA workbench integrates V&V aspects into its modelling environment, such that these techniques can be of assistance in the process of knowledge acquisition and representation. To this end, verification has to be performed incrementally and can no longer be delayed until after the system has been completed. It will be shown how this objective can be realised through an approach that uses the decision table formalism as a modelling instrument.     

NH4SCN从ROH-CTMAB-C12H26载金有机相中反萃金

研究了硫氰酸铵（NH4SCN）从混合醇（ROH）－十六烷基三甲基溴化铵（CTMAB）－正十二烷（C12H26）载金有机相中反萃金，考察了平衡时间，PH值，反萃剂浓度，温度等因素对反萃率的影响及有机相的循环使用，绘制了反萃等温曲线，结果表明，NH4SCN对金具有较高反萃率，可顺利实现金的反萃。     

Ti-26高强钛合金斜轧穿孔工艺研究

研究了Ti-26高强钛合金斜轧穿孔制备管坯工艺。测试了穿制的Ti-26合金管坯的力学性能，用金相显微镜观察了管坯的显微组织，用扫描电镜分析了拉伸断口的形貌。结果表明，采用斜轧穿孔方式完全可以制备Ti-26高强钛合金管坯；在1050℃下，选择合适的轧辊转速和前进角可顺利穿制Ti-26高强钛合金管坯，其管坯的强度为815MPa，延伸率达到13％，断面收缩率达到45％，晶粒度按ASTME标准为6级，比穿孔前细化，断口呈明显的塑性断口，加工管材无需热处理可以直接进行轧制，道次加工率可达45．8％。     

Nanocomposite route to the stabilization of porous ϑ-alumina

Stabilization of -alumina phase by silica was studied in nanocomposite (diphasic) alumina-silica gels by XRD and BET surface areas measurements. Five wt.% of silica (22 nm particles) increased the crystallization temperature of to -alumina by about 100°C from boehmite (10 nm particles) derived alumina. Stabilization of -alumina was caused by the formation of intimate contact (Al-O-Si) between components by diffusion of silica into the defect alumina structure.Also with the Department of Agronomy.     

Hot compression deformation behavior of MB26 magnesium alloy

The flow stress features of MB26 magnesium alloy were studied by isothermal compression at 300-450 ℃ and strain rate of 0.001^-1 s J with Gleeble 1500 thermal simulator. In addition, the deformation activation energy Q was calculated. The results show that the strain rate and deformation temperature have obvious effect on the true stress. The peak value of flow stress becomes larger with increasing strain rate at the same temperature, and gets smaller with the increasing deformation temperature at the same strain rate. The alloy shows partial dynamic recrystallization. The flow stress of MB26 magnesium alloy during high temperature deformation can be represented by Zener-Hollomon parameter including the Arrhemius term. The temperatt, re range of 350-400℃ is suggested for hot-forming of this alloy.     

超高纯铁素体不锈钢在3．5％NaCl中的腐蚀疲劳的裂纹萌生

本文利用三电极技术研究了超高纯铁素体不锈钢Ｆｅ－２６Ｃｒ－１Ｍｏ在３．５％ＮａＣｌ水溶液转化体系中，低周腐蚀疲劳的裂纹萌生行为．在静态点蚀电位以下，形变诱发点蚀出现，但是点蚀在本文的研究体系不是导致裂纹萌生的原因．在低应变速率下，裂纹沿晶内的驻留滑移带萌生，且沿滑移带的电化学溶解加快了裂纹萌生．在高应变速率下，裂纹在晶界萌生，且沿晶界有点蚀实验结果表明，电化学溶解加速了裂纹萌生，点蚀在此钝化体系中不是裂纹萌生的机制．应变速率影响裂纹萌生方式．