Corrosion fatigue of extruded magnesium alloys

Corrosion fatigue tests were carried out on extruded AZ31 (3% Al, 1% Zn, 0.3% Mn, Mg—the rest), AM50 (5% Al, 0.4% Mn, Mg—the rest) and ZK60 (5% Zn, 0.5% Zr, Mg—the rest) Mg alloys in air, NaCl-based and borate solutions. N_sol/N_air ratios (the relative fatigue life) were used for the analysis of the corrosion fatigue behavior of Mg alloys in various environments, where N_sol and N_air are the numbers of cycles to failure in the solution and in air, respectively. Extruded ZK60 alloy reveals very high fatigue and corrosion fatigue properties in comparison with other alloys. However, it has the lowest relative fatigue life (N_sol/N_air 10⁻³–10⁻²) or the highest sensitivity to the action of NaCl-based solutions in comparison with that of AM50 and AZ31 alloys (N_sol/N_air 10⁻²–10⁻¹). Under the same stress, the corrosion fatigue life of extruded alloys is significantly longer than that of die-cast alloys (N_sol for extruded AM50 in NaCl is two to three times longer than that of die-cast AM50).     

Decisive arrival law parameters and a general finite capacity queueing problem

This paper addresses the problem of finding the parameters of the arrival law which most significantly influence expected occupation and loss of a finite capacity queue. The input process is supposed to be ergodic and wide sense stationary. We show that it is mostly possible to fit an MMPP(2) to the decisive parameters of observational data. Numerical examples illustrate the importance of the decisive parameters, called key parameters, and also show the accuracy of the proposed fitting procedure. Finally, in the appendix we present the solution of the finite capacity queueing problem with Special Semi Markov Process (SSMP) arrivals and a general service strategy.     

70推土机主离合器分离杆螺栓失效分析

主离合器分离杆螺栓是一个重要安全件，使用中经常发生断裂。经过失效分析确定断裂原因是由其配件引起。提高配件的冷加工质量及改进结构，可解决分离杆螺栓的断裂问题。     

变形镜交连值的优化分析

关于优化光波控制,自适应光学校正是至关重要的一个环节,可用于改善激光光束质量及校正光束在传输过程中气流引起的波前畸变等。变形镜是其核心器件,而交连值是影响变形镜校正精度的关键因素。针对变形镜实际使用时需要对致动器进行一定的约束,利用带约束的最小二乘法,分析了在一定约束条件下交连值变化对变形镜校正精度及控制稳定性的影响。以Zernike像差和以大气湍流模型构造的像差为校正对象,寻找校正效果最好的交连值。结果表明各阶Zernike像差对应的最优交连值差异较大,最优交连值主要分布在15%～35%之间。从控制误差引起的校正效果变化的方面考虑,对正方形致动器排布的最优交连值位于15%～25%区域。     

型腔体组件装配尺寸检测技术分析与运用

为解决型腔体组件装配尺寸的检测问题,以某枪型的型腔体组件为例,分析该型腔体组件的结构特点,设计组合型检测装置,实现准确检测目的.归纳总结了型腔体组件装配尺寸检测技术运用过程中检测装置的设计要领,采用设计与被测型腔体组件相匹配的组合型检测装置,有效解决了型腔体组件装配尺寸检测过程中的定位困难、操作繁琐、检测准确性差等问题.该检测技术对确保型腔体组件装配尺寸的检测稳定性、检测可操作性、检测准确性等方面具有现实的指导意义.     

计算机内部时间长期稳定性分析

介绍了计算机内部时间的原理;设计了利用GPS提供的高精度UTC时间求取计算机内部时间钟差钟速的实验方案;进行了连续90天的实验,积累了175个时段的实验数据;分别利用多项式模型、傅里叶级数模型以及正弦和函数模型,对这些实验数据进行了钟差长期变化的拟合分析。分析表明:计算机内部时间的长期变化规律主要呈线性变化趋势,同时又含有周期性的影响;拟合精度最高的是七阶正弦和函数模型,其拟合残差中误差为0.289秒。     

一种NURBS曲面拟合精度的量化评测算法

曲面重构是逆向工程中的核心技术之一,由于NURBS曲面在光顺性和局部可编辑等方面所具有的优点,使其成为点云数据自由曲面重构的常见形式。目前对NURBS曲面重构技术的研究上取得了一些成果,但各方法在拟合精度和效果上各有参差,因此有必要对NURBS曲面拟合精度评价算法进行研究。在采用NURBS实现曲面拟合的基础上,对拟合精度的量化指标进行研究,设计了一种基于区域划分的搜索迭代算法,可快速地计算得到原始点云与NURBS曲面的偏差。     

An approximation method with data selection process

In this paper we present a method curve approximation from a given Lagrangian data set. An approximating problem of curves is obtained by minimizing a quadratic functional in a suitable space. This method is justified by a convergence result and an analysis of a numerical and graphical example.     

基于图像处理的显微外科手术质量评价研究*

目前显微外科手术质量评定仍采用测角计进行手工测量,测量中有一定的随意性,测量误差大。针对该问题,提出了应用图像处理技术对显微外科接指手术进行分析和质量评价的方法。通过与手工测量进行对比,图像处理方法评价客观,测量精度高,得到了满意的结果。