基于多通道的ICU脑血管疾病死亡风险预测模型

死亡风险预测指根据病人临床体征监测数据来预测未来一段时间的死亡风险。对于ICU病患，通过死亡风险预测可以有针对性地对病人做出临床诊断，以及合理安排有限的医疗资源。基于临床使用的MEWS和Glasgow昏迷评分量表，针对ICU病人临床监测的17项生理参数，提出一种基于多通道的ICU脑血管疾病死亡风险预测模型。引入多通道概念应用于BiLSTM模型，用于突出每个生理参数对死亡风险预测的作用。采用Attention机制用于提高模型预测精度。实验数据来自MIMIC [Ⅲ]数据库，从中提取3?080位脑血管疾病患者的16?260条记录用于此次研究，除了六组超参数实验之外，将所提模型与LSTM、Multichannel-BiLSTM、逻辑回归（logistic regression）和支持向量机（support vector machine, SVM）四种模型进行了对比分析，准确率Accuracy、灵敏度Sensitive、特异性Specificity、AUC-ROC和AUC-PRC作为评价指标，实验结果表明，所提模型性能优于其他模型，AUC值达到94.3%。     

基于滚动摩擦作用下玉米颗粒在模拟筒仓卸料中的力链分析（网络首发、推荐阅读）

针对颗粒滚动摩擦作用对筒仓中玉米颗粒的力链空间分布进行研究，通过EDEM离散元软件建立筒仓模型与仿真玉米颗粒模型进行卸粮仿真模拟，并与筒仓卸料实验作流态对比，验证模型与仿真结果的准确性。通过对模拟仓进行切片观察和数据处理，对比分析了不同摩擦情况下力链的细观参数随时间演化规律。模拟结果表明：颗粒间摩擦系数越大，卸粮完成的最终时间越长；颗粒间滚动摩擦系数越小，颗粒由整体流转变为管状流的时间越早。对于有漏斗的筒仓来说，减小颗粒间摩擦会改变整体流和管状流之间的极限，从而增加产生管状流的面积。标准滚动摩擦系数下玉米颗粒在卸料过程中会出现起拱-塌陷效应；减小滚动摩擦，玉米颗粒卸料较稳定，未出现起拱的应力突增、以及拱塌陷的应力衰减；增大颗粒间滚动摩擦不但会增加拱效应，且出现成拱高度距离漏斗口更高。     

Localized corrosion of (lean) duplex stainless steels in immersion units of urban wastewater treatment plants

With lower alloying cost and higher mechanical properties, lean duplex stainless steels can be an alternative to the more commonly used austenitic stainless steels. However, these alloys are still not the preferred choice, probably due to a lack of field experience. A study was thus initiated in view of defining the limits of use of selected (lean) duplexes for urban wastewater treatment units. The present paper shows the localized corrosion performance of selected lean duplexes in chloride contaminated solutions. The results are compared with austenitic S30403 and S31603 and with the more standard duplexes S82441 and S32205. The effect of welding was also investigated. Exposures in field municipal wastewater plants were conducted for 1 year in low and high chloride content units. The results show that lean duplexes S32101 and S32202 can be used as alternatives to S30403 and S31603 in low chloride electrolytes. At 500 ppm of chloride content, duplex stainless steel S32304 showed better corrosion resistance than S30403 and S31603. For higher chloride contents (1000 ppm and above) the standard duplexes S82441 and S32205 shall be preferred.     

Characterizations of friction welding joint interface for AISI 316

Because of heat amount is different from peripheral to central of friction welding interface, which is leaded to vary the characterizations along that interface. Current study, respectively, focused on the effect of different friction pressure on micro-structural and mechanical properties of that friction welding joint interface. Presently, these friction pressures are 110, 130, 150 and 170 MPa while kept all other conditions constant. The effects of different friction pressure on welding interface characterization were investigated by EDX, SEM, tensile, compression, impact and hardness tests. The tensile tests carried out on the standardized test piece with diameter 6 mm and 8 mm, thus, compression tests were extracted from the positions of 0°, 45° 90° with test specimen of 4 mm diameter and 6.5 mm length at weld center. Whereas, the impact test pieces were picked up in two positions, the first one is symmetrical, which it obtained to the respect of the rotation axis and the interface, on the other hand, the second one is non-symmetrical with the axis of rotation and symmetrical to the interface, for making the notch head coincide with the center of the welded joint, The obtained results showed that with reducing of friction pressure will present lack of bonding increasing from peripheral toward the welding center, which will responsible on reducing of the mechanical properties such as tensile, compression and impact strength.     

A review on ultrasonic spot welding of copper alloys

As a solid state joining process, ultrasonic spot welding has been proven to be a promising technique for joining copper alloys. However, challenges still remain in employing ultrasonic spot welding to join copper alloys. This article comprehensively reviews the current state of ultrasonic spot welding of copper alloys with a number of critical issues including materials flow, plastic deformation, temperature distribution, vibration, relative motion, vertical displacement, interface friction coefficient, online monitoring technique, coupled with the macrostructure and microstructure, the mechanical properties and electrical conductivity. In addition, the future trends in this field are provided.     

（S）-噻吗洛尔半水合物的合成及表征

为了开发β受体阻断剂新药（S）-噻吗洛尔半水合物，采用3-吗啉-4-氯-1，2，5-噻二唑为起始原料，经水解反应得到中间体1（3-吗啉-4-羟基-1，2，5-噻二唑）。中间体1与R-环氧氯丙烷发生醚化反应，经后处理及重结晶得到中间体2 {（R）-4-［4-（环氧乙烷-2-基甲氧基）-1，2，5-噻二唑-3-基］吗啉}。中间体2经胺化反应、马来酸成盐及重结晶得到（S）-马来酸噻吗洛尔。（S）-马来酸噻吗洛尔经游离、纯水转晶得到符合药典标准的（S）-噻吗洛尔半水合物，总收率14.05%且e.e.值为99.66%。最终成品经IR、1H-NMR、13C-NMR、MS、TGA、DSC表征，并优化各步反应条件。结果表明:以三乙胺为醚化反应缚酸剂75 ℃反应最佳；以乙醇为胺化反应溶剂46 ℃反应16 h最佳；S-噻吗洛尔的转晶拆分以水作溶剂，比传统不对称合成工艺安全稳定，操作简单，适合工业化生产。     

Friction compensation controller for load varying machine tool feed drive

The load applied to a machine tool feed drive changes during the machining process as material is removed. This load change alters the Coulomb friction of the feed drive. Because Coulomb friction accounts for a large part of the total friction the friction compensation control accuracy of the feed drives is limited if this nonlinear change in the applied load is not considered. This paper presents a new friction compensation method that estimates the machine tool load in real time and considers its effect on friction characteristics. A friction observer based on a Kalman filter with load estimation is proposed for friction compensation control considering the applied load change. A specially designed feed drive testbed that enables the applied load to be modified easily was constructed for experimental verification. Control performance and friction estimation accuracy are demonstrated experimentally using the testbed.     

施工中电焊机的安全使用简述

从电焊机自身电气特点及建筑工地工作环境入手,探讨电焊机安全技术的实施方法。分析电焊机安全隐患及事故的分类以及电焊机在使用过程中产生危险的原因。介绍电焊机在安装以及作业过程中的安全措施。     

改进HSR-FCN的服装图像识别分类算法研究

目前网络上的服装图像数量增长迅猛，对于大量服装图像实现智能分类的需求日益增加。将基于区域的全卷积网络（Region-Based Fully Convolutional Networks，R-FCN）引入到服装图像识别中，针对服装图像分类中网络训练时间长、形变服装图像识别率低的问题，提出一种新颖的改进框架HSR-FCN。新框架将R-FCN中的区域建议网络和HyperNet网络相融合，改变图片特征学习方式，使得HSR-FCN可以在更短的训练时间内达到更高的准确率。在模型中引入了空间转换网络，对输入服装图像和特征图进行了空间变换及对齐，加强了对多角度服装和形变服装的特征学习。实验结果表明，改进后的HSR-FCN模型有效地加强了对形变服装图像的学习，且在训练时间更短的情况下，比原来的网络模型R-FCN平均准确率提高了大约3个百分点，达到96.69%。     

平面并联机构工作空间的三维螺旋扫描CAD求解

针对平面并联机构无奇异位置工作空间求解困难、过程繁琐、计算量大等问题，提出了基于CAD求解平面并联机构工作空间的三维螺旋扫描方法。将[n]自由度平面并联机构分解成[n]条支链进行独立分析，得到每条支链下末端执行器的可达区域，再将所有支链可达区域取交集即为平面并联机构工作空间。应用SolidWorks软件建立平面并联机构模型，进行几何特征处理，通过自动求解器求解，将求解过程图形化，快速得到同轴布局5R机构和平面3-RPR并联机构的无奇异位置工作空间。通过同轴布局5R机构的运动学实验，验证了该求解方法的可行性。