Numerical study of entropy generation in Darcy-Forchheimer (D-F) Bödewadt flow of CNTs

Three-dimensional Bödewadt flow (fluid rotates at a large enough distance from the stationary plate) of carbon nanomaterial is examined. Single walled and multi walled CNTs are dissolved in water and gasoline oil baseliquids. Darcy-Forchheimer porous medium is considered. Stationary disk is further stretched linearly in radial direction. Heat transfer effect is examined in presence of radiation and convection. Effect of viscous dissipation is accounted. Entropy generation rate is studied. By using adequate transformation (von Kármán relations), the flow field equations (PDEs) are transmitted into ODEs. Solutions to these ODEs are constructed via implementation of shooting method (bvp4c). In addition to Entropy generation rate, Bejan number, heat transfer rate (Nusselt number), skin friction and temperature of fluid are examined through involved physical parameters. Axial component of velocity intensifies with increment in nanoparticles volume fraction and ratio of stretching rate to angular velocity parameter while it decays with higher porosity parameter. Higher nanoparticles volume fraction and porosity parameter lead to decay in radial as well as tangential component of velocity. However it enhances with higher ratio of stretching rate to angular velocity parameter. Temperature of fluid directly varies with higher ratio of stretching rate to angular velocity parameter, radiation parameter, Eckert number, Biot number and nanoparticles volume fraction. Rate of Entropy generation is reduced with higher estimations of porosity parameter, nanoparticles volume fraction and radiation parameter. Skin friction coefficient decays with higher porosity parameter and ratio of stretching rate to angular velocity parameter. Intensification in porosity parameter, nanoparticles volume fraction and Biot number leads to higher Nusselt number. Prominent impact is shown by multiple-walled CNTs with gasoline oil basefluid than single-walled CNTs with water basefluid.     

玉门减压深拔减五线生产微晶蜡的工艺研究及应用

对玉门减压深拔减五线生产微晶蜡的工艺进行了研究并进行了工业应用,生产结果表明:以减压深拔减五线为原料经酮苯脱蜡脱油、白土精制生产微晶蜡,操作过程平稳,酮苯脱蜡脱油过程过滤速度较快,脱蜡油和粗蜡的平均收率可达到78.24%。微晶蜡产品质量符合SH/T 0013-1999标准要求。     

Study on Laboratory Method for Refining of SR Diesel Fuel

The method for refining the straight-run diesel fuel was studied in laboratory scale in order to make the acid number of diesel fraction comply with the standard while removing the naphthenic acids contained in diesel without causing environmental pollution. After comparing the effect of refining using three solvents, the isopropyl alcohol-HOA was specified as the best solvent. Meanwhile, the relationship between the acid number of diesel fraction and the amount of solvent used and the relationship between the concentration of solvent and temperature and the stability of diesel in terms of its acid number were also investigated. Experimental results had shown that when the mass fraction of the HOA-IPA solvent was 20% at a dosage of 17 mL of the solvent and a temperature of 30℃, the acid number of the refined diesel fraction was 0.015 mg KOH/g with a good stability of acidity in the diesel fraction,     

我国炼油石化产业应对石油短缺时代的科技对策思考

分析了我国石油消费的增长趋势和石油的增产潜力，指出持续增长的需求和相对稳定的产量使我国对国际石油的依存度越来越高。综合了国际能源机构、能源经济学家和石油地质学家对世界石油供应前景的预测结果，认为世界石油短缺的时代并不遥远。提出了我国炼油石化产业应对世界石油供应短缺时代的科技对策：（I）抓紧开发和完善充分利用石油资源生产运输燃料和石化原料技术；（2）开发用煤炭、石油焦、沥青制氢和炼油过程耦合的廉价氢源技术和用氢优化技术；（3）开发炼油石化过程节能降耗技术；（4）开发天然气及煤制油、甲醇制乙烯、丙烯技术；（5）开发利用生物质生产车用替代燃料、生物材料和生物化学品技术。     

油气吸收回收系统的研究及工业应用——(Ⅰ)中型试验及结果分析

在蒸发油气吸收回收技术小试研究的基础上，开发出常温常压吸收法油气回收中试装置，并利用已开发的吸收剂AbsFOV-97进行了中试试验。结果表明，当系统进料气、吸收剂AbsFOV-97、汽油的体积流量比为10．0：1．0：0．5、真空泵解吸压力小于13．3kPa时，系统回收率高达97％以上，高于设计指标，且回收汽油的质量满足使用要求。统计数据表明，油气回收系统进料气、尾气中平均油气摩尔质量分别为65．51、48．97g／mol，该值可为油品蒸发损耗及其控制技术的评价提供参考。     

FCC汽油光催化氧化脱硫的实验室研究

采用光催化氧化与液液萃取同时进行的方法，考察了光敏剂十六烷基三甲基溴化铵的用量、pH值、双氧水体积分数和反应时间对脱硫效果的影响。结果表明，在光源为主波长365nm的300W中压汞灯，双氧水体积分数为25％，FCC汽油与双氧水体积比为1：3，总体积为120mL，加入0．20g十六烷基三甲基溴化铵，以7000r／min高速均质5min，pH值为4，光照10h的实验条件下，FCC汽油脱硫率可达91．20％；脱硫后的双氧水及光敏剂可以重复使用，不会造成二次污染。