流量自动控制的设计与实现

文章通过分析多相流模拟井的实际工作要求 ,提出了简单实用的流量自动控制模型。应用成型的计算机数据采集和控制模块及稳定可靠的流量控制部件 ,实现了各相流量的自动控制过程。该流量自动控制系统调节精度高、速度快、整体造价低 ,在实际应用中取得了良好的效果。     

Al2O3/TiB2/SiCw三元复合材料的力学性能及显微结构

以Al₂O₃为基体,SiC晶须和TiB₂颗粒两种增韧剂,采用热压烧结工艺制备了Al₂O₃/TiB₂/SiC_w三元复合陶瓷材料。研究了热压工艺参数对材料致密度的影响和晶须含量对该复合材料的力学性能和显微结构的影响。结果表明;随晶须含量的增加,该复合材料的热压温度和保温时间需要相应的增加;晶须拔出、裂纹偏转和晶须的桥接为该复合材料的主要增韧机理;随晶须含量的增加,该材料的室温断裂韧性增加;该材料的断裂韧性随温度的升高而呈增大趋势,并且晶须含量越高,材料的高温断裂韧性增幅越大。     

ZrSiO4/Al2O3烧结氧化铝-莫来石复相陶瓷微观结构的研究

将氧化铝和锆英石混合物试样分别在1350℃、1550℃下烧成，结果发现在1350℃烧成、保温3h的样品中有莫来石生成，而在1550℃烧成、保温3h的情况下却未发现莫来石生成，本文对此作了分析和探讨。关键词：氧化铝一莫来石，复相陶瓷，微观结构。     

NUMERICAL SIMULATION OF THE GAS-PARTICLE FLOW IN RISERS I: THE MACRO FLOW BEHAVIOR

The steady gas-particle flow in risers under variant operating conditions was predicted based on a k-ε-k_p-ε_p-Θ two-fluid model, which describes the dense turbulent gas-particle flow by the Eulerian method, considering the turbulence of both gas and particles as well as the particles' collisional effects. Much information on the macro flow behavior in risers, such as the profiles of local particle axial velocity, solids volume fraction, and solids mass flux in different operating regimes was obtained, and the predicted results show satisfactory agreement with experimental data. Further analysis of the predictions gives the comprehension of flow characteristics on the macro scale.     

原位合成TiB2-TiCx复相陶瓷的显微组织

应用光学显微镜(OM)、X射线衍射(XRD)、透射电镜(TEM)和扫描电镜(SEM)对原位合成的TiB2-TiCx复相陶瓷显微结构进行了分析。并分析了Ti-B4C反应的原位生成机理。结果表明,Ti3B4相稳定存在于生成物中,其形态与形成温度和反应机理有关。     

快速流化床中颗粒团聚现象的数值模拟——曳力关联式的选择

Drag force is a key parameter in the numerical modeling of gas-particle flow in circulating fluidized beds. The reliability of current drag force correlations over the regime of fast fluidization has, however, not been thoroughly investigated. In this article, a drag force correlation accounting for the clustering effects for Geldart A particles is used to simulate the behaviors typical of fast fluidization, including dynamic evolution of clusters as well as time- averaged axial and lateral voidage profiles. Diverse images of clusters are captured and the time-averaged profiles of voidage are shown to be in quantitative agreement with the present empirical correlation. The results based on different constitutive correlations of drag force show the importance of the choice of drag force in modeling fast-fluidized beds. This drag force correlation, based on a simple averaging assumption, could give some basic insights about the magnitude of the drag reduction.     

莫来石晶种对反应烧结ZrO2/莫来石复相陶瓷显微结构的影响

通过显微结构观察研究了莫来石晶种对反应烧结ZrO2/莫来石复相陶瓷显微结构的影响。研究结果表明：与不含晶种试样相比，添加Ma(d50=1.87μm)和Mb(d50=0.83μm)晶种试样的显微结构比较均匀，莫来石晶粒多呈等轴状，且大小均一，晶内型ZrO2和封闭气孔较少。添加晶种对莫来石晶粒有明显细化作用。但晶种添加量和晶种颗粒尺寸对反应生成莫来石的晶粒尺寸无明显影响。采用溶胶－凝胶法制备的莫来石晶种（Mc)使试样中长出了一定量的长柱状的莫来石晶粒。     

LDA Measurements on a Turbulent Gas/Liquid/Fibre Suspension

Detailed continuous phase flow measurements (mean and RMS velocities) by Laser Doppler Anemometry (LDA) of a turbulent gas/fibre/liquid suspension in a rotary shear tester have been performed with simultaneous torque measurements. The model system comprises a refractive‐index matched suspension in the 4‐12% wt. range with gas contents up to 15% vol. The two transition points, found by Andersson and Rasmuson (2000), were detected also with gas present and appear at higher impeller speeds with increasing gas and fibre concentrations. Plotting RMS and mean velocities versus impeller speed and power input, it is found that both decrease with increasing gas and fibre contents.     

Simulation of the Impact Between Head and Seat Head Restraint During REC Under Consideration of the Multiphase and Nonlinear Features

The impact process between car drivers head and seat head restraint during a car rear end collision is simulated, where the multiphase and nonlinear features of the human brain tissues and the foam material of the seat head restraint are considered. Using the FEM-software LS-DYNA, the brain tissue deformation caused by a car REC is calculated. The purpose of this work is to supply references for improving the design of the head protective devices. The results show that the maximum shear strain appears near the boundaries of different phases and there is a great shear strain gradient in the brain tissues.