Grain orientation evolution and multi-scale interfaces enhanced thermoelectric properties of textured Sr0.9La0.1TiO3 based ceramics

Sr_0.9La_0.1TiO₃ based textured ceramics (SLTT-S3T) with a texture fraction of 0.81 are successfully fabricated by the reactive template grain growth method, in which Sr_0.9La_0.1TiO₃/20 wt%Ti was used as matrix and 10 wt% plate-like Sr₃Ti₂O₇ template seeds were used as templates. The phase transition, microstructure evolution, and the anisotropic thermoelectric properties of SLTT-S3T ceramics were investigated. The results show that the ceramics are mainly composed of Sr_0.9La_0.1TiO₃ and rutile TiO₂ phases. Grains grow with a preferred orientation along (h00). A maximum ZT of 0.26 at 1073 K was achieved in the direction perpendicular to the tape casting direction. The low lattice thermal conductivity of 1.9 W/(m K) at 1073 K was obtained decreased by 34%, 40%, and 38% compared with non-textured, SrTiO₃ and Sr_0.9La_0.1TiO₃ ceramics prepared by the same process, can be attributed to the enhanced phonon scattering by the complex multi-scale boundaries and interfaces. This work provides a strategy of microstructural design for thermoelectric oxides to decrease intrinsic lattice thermal conductivity and further regulate thermoelectric properties via texture engineering.     

Predicting Prostephanus truncatus (Horn) (Coleoptera: Bostrichidae) populations and associated grain damage in smallholder farmers’ maize stores: A machine learning approach

Prostephanus truncatus is a notorious pest of stored-maize grain and its spread throughout sub-Saharan Africa has led to increased levels of grain storage losses. The current study developed models to predict the level of P. truncatus infestation and associated damage of maize grain in smallholder farmer stores. Data were gathered from grain storage trials conducted in Hwedza and Mbire districts of Zimbabwe and correlated with weather data for each site. Insect counts of P. truncatus and other common stored grain insect pests had a strong correlation with time of year with highest recorded numbers from January to May. Correlation analysis showed insect-generated grain dust from boring and feeding activity to be the best indicator of P. truncatus presence in stores (r = 0.70), while a moderate correlation (r = 0.48) was found between P. truncatus numbers and storage insect parasitic wasps, and grain damage levels significantly correlated with the presence of Tribolium castaneum (r = 0.60). Models were developed for predicting P. truncatus infestation and grain damage using parameter selection algorithms and decision-tree machine learning algorithms with 10-fold cross-validation. The P. truncatus population size prediction model performance was weak (r = 0.43) due to the complicated sampling and detection of the pest and eight-week long period between sampling events. The grain damage prediction model had a stronger correlation coefficient (r = 0.93) and is a good estimator for in situ stored grain insect damage. The models were developed for use under southern African climatic conditions and can be improved with more input data to create more precise models for building decision-support tools for smallholder maize-based production systems.     

黑龙江省节水增粮行动(2012—2015年)实施方案

文章通过对黑龙江省高效节水现状,存在问题的分析,结合黑龙江省高效节水发展的支撑能力,阐述黑龙江省节水增粮目标、任务及总体布局,为黑龙江省2012—2015年节水增粮实施提供依据。     

Effects of SiC content on the densification,microstructure, and mechanical properties of HfB2–SiC composites

To investigate the effects of SiC on microstructure, hardness, and fracture toughness, 0, 10, 20, and 30 vol% SiC were added to HfB₂ and sintered by SPS. Upon adding SiC to 30 vol%, relative density increased about 4%; but HfB₂ grain growth had a minimum at 20 vol% SiC. This may be due to grain boundary silicate glass, responsible for surface oxide wash out, enriched in SiO₂ with higher fraction of SiC. By SiO₂ enrichment, the glass viscosity increased and higher HfO₂ remained unsolved which subsequently lead to higher grain growth. Hardness has increased from about 13 to 15 GPa by SiC introduction with no sensible variation with SiC increase. Residual stress measurements by Rietveld method indicated high levels of tensile residual stresses in the HfB₂ Matrix. Despite the peak residual stress value at 20 vol% SiC, fracture toughness of this sample was the highest (6.43 MPa m^0.5) which implied that fracture toughness is mainly a grain size function. Tracking crack trajectory showed a mainly trans-granular fracture, but grain boundaries imposed a partial deflection on the crack pathway. SiC had a higher percentage in fracture surface images than the cross-section which implied a weak crack deflection.     

Reducing treatment zone diameter in orthokeratology and its effect on peripheral ocular refraction

PurposeTo determine whether orthokeratology (OK) induced treatment zone (TZ) diameter can be reduced by altering OK lens design, and if so the impact of modifying TZ diameter on relative peripheral refraction (RPR).Methods16 subjects (mean age 23.4 ± 1.5 years; 8 female) completed the study. Standard (Control) OK lens design (PJ, Capricornia, Australia) or a modified version (Test) where the back optic zone diameter was reduced, and back optic zone asphericity and intermediate lens curves were altered, were worn overnight only for 7-nights in a randomised double masked order, with a minimum 1-week wash out (no lens wear) between lens designs. Full correction of refractive error was targeted. Refraction; best corrected visual acuity (BCVA); RPR (Shin-Nippon NVision-k 5001) along the horizontal and vertical meridians; and corneal topography (Medmont E300) were measured before starting lens wear and in the morning after lens removal after the seventh night of lens wear for both lens designs. TZ diameter and decentration was calculated from corneal topography.ResultsAfter 7-nights of wear both lens designs created -2.00D refraction effect with no significant difference in refractive effect or change to BCVA between the designs. The Test design created a significantly smaller horizontal (4.78 ± 0.37 vs 5.70 ± 0.37 mm, p < 0.001) and vertical (5.09 ± 0.51 vs 5.92 ± 0.51 mm p < 0.001) TZ diameter. The TZ was decentered inferior temporal with no significant difference between designs. There was no significant difference between the lens designs in RPR along the horizontal and vertical meridians at any measurement period.ConclusionsOK induced TZ diameter can be reliably reduced by altering OK lens design without detrimentally effecting lens centration or refractive effect. Reducing TZ diameter did not alter RPR, though measurement artifacts could be responsible for masking an effect. Longitudinal studies are needed to assess whether smaller TZ OK lens designs increase efficacy for slowing progression of myopia.     

浅析火力发电厂汽水系统中内径管与外径管的设计选择

按照管道加工工艺的不同,管道可分为内径控制管和外径控制管。通过热轧工艺生产的外径控制无缝钢管,可满足火力发电厂汽水系统中绝大部分管道的使用要求。对于超(超)临界机组的主蒸汽和高温再热蒸汽管道采用的P91/P92材质的大口径厚壁无缝钢管,由于对材料性能和加工工艺有特殊要求,因此宜采用内径控制管。     

一种估算单桩经济直径的方法

在滩海油田开发过程中,经常需要设立立管桩,在环境荷载的作用下,立管桩顶部会发生位移,较大的位移对立管及栈桥的安全很不利,因此需要合理确定单桩的直径。埕岛油田在确定单桩直径时引入了经济直径的概念,文章对经济直径的原理进行了分析,给出了桩顶位移和桩径经济指数计算公式,并举例进行了计算,得出了桩径与桩顶位移及桩径经济指数的关系曲线, 进而求得经济桩径的取值范围。文章还对该方法的优缺点进行了分析。