Prediction of rock mass P wave velocity using blasthole drilling information

In this paper, the development of the models for the prediction of rock mass P wave velocity is presented. For model development, the database of 53 cases including widely used and recorded drilling parameters and P wave velocity was constructed from the field studies conducted in 13 open pit lignite mines. Both conventional linear, non-linear multiple regression and Adaptive Neuro Fuzzy Inference System (ANFIS) were used for model development. Prediction performance indicators showed that ANFIS model presented the best performance and it can successfully be used for the preliminary prediction of P wave velocities of rock masses.     

An Experimental Investigation into the Feed Rate Capacity of Rotary Valve and Blow Tank Feeders

Industry widely uses rotary valves and blow tanks for the pneumatic conveying of products, each having their pros and cons depending on the specific application. This article shows the differing results obtained when low-velocity conveying a product through a common pipeline using both a drop-through rotary valve and a bottom-discharge blow tank feeder. A number of issues arise in the rotary valve system, the main one being rotary valve air leakage. A blow tank system, on the other hand, does not leak, as it is an enclosed system. The experimental results show dramatic differences in product throughput. Further exploration leads to a novel modification being made to the rotary valve system in an attempt to increase its capacity. The result of this modification shows a slight increase in output tonnage, but still significantly less than that obtained from the blow tank.     

钛精矿回转窑直接还原过程结圈可能性的探讨

通过煤种，入窑球冷态强度和还原过程强度，以及钛精矿与煤灰混合物的软化温度等分析探讨了钛精矿预热球团回转窑直接还原产生结圈的可能性，获得了可以避免结圈的结论。     

滚动转子式压缩机传热模拟

就滚动转子式压缩机的传热特性进行了分析。把压缩机分为15块，视摩擦损失和电机发热为内热源，考虑润滑油流动在传热过程中的影响，应用集中参数法对每块进行了能量分析，建立了传热数学模型并进行了计算。     

Prediction of axial velocity profiles and solids hold-up in a rotary kiln

Axial bed depth profiles were experimentally measured in a rotary kiln containing ilmenite particles under steady state and transient conditions. The variables include feed rate of solids, inclination and rotational speed of the kiln. and dam height. The variation of the axial velocity with kiln axis was estimated. The semi-experimental model proposed by Perron and Bui (1990) was modified to include the effect of the variables of the present study. The mean residence time of solids was estimated from the fractional hold-up and expressed in terms of the process variables. The transients induced by a step change in any of the operating conditions were measured as variation of discharge rate of solids with time.     

天津钢管公司DRC直接还原厂生产工艺与自动控制

天津钢管公司DRC直接还原厂将采用英国戴维国际工程公司的DRC煤基直接还原技术,以铁矿石、煤、石灰石为原燃料,用回转窑来生产直接还原铁(DRI)。该厂将由两条回转窑生产线组成,每条生产线的生产能力为15万tDRI/年,回转窑规格为φ5.0m×80m。工厂生产主线将采用计算机集散控制系统(DCS)以实现对生产过程的自动控制。     

三辊穿孔和轧管所产生的钢管壁厚极差和波浪形内螺纹

定量描述了实际生产过程中三辊斜轧穿孔所产生的钢管壁厚极差和波浪形内螺纹，初步探讨了三辊轧管机对钢管壁厚极差和波浪形内螺纹的影响。     

气动冲击器研究现状及发展趋势

阐述了气动冲击旋转钻井用气动冲击器国内外近期的研究现状,以及各类冲击器的结构和性能参数,并提出了气动冲击器的发展趋势。     

日产1000t水泥熟料生产线的提产措施

通过对五级旋风筒下料管、回转窑转速、配料方案、物料稳定等四方面进行改进,达到提产目的。     

磁性旋转编码传感器的研制

本文介绍的两相输出磁性旋转编码器输出电压V_(p-p)=41mV(V_(cc)=5V),灵敏度为6.3μV/(A·m~(-1)),分辨率为400p/r.实验证明,磁鼓与磁阻传感器之间存在最佳间隙,当间距为1mm时,输出最大.