搅拌式风力致热装置启动性能研究

搭建搅拌式风力致热试验台,以自制的2种致热器为研究对象,使其分别在3个不同平均角加速度24.92、14.66、8.04 rad/s2下启动。通过动态扭矩测试仪和数据采集仪测试记录致热器启动阶段的相关数据。结果表明:致热器启动时所需扭矩与角加速度的一次方、转速、叶片半径的二次方成正比,同时得出这些因素之间的关系式;满负荷时,启动扭矩会出现一个峰值,且角加速度越大峰值越大,自然风必须提供峰值以上的扭矩,否则装置无法启动。     

Review of pulsed thermal NDT: Physical principles,theory and data processing

This paper summarizes the basics of pulsed thermal nondestructive testing (TNDT) including theoretical solutions, data processing algorithms and practical implementation. Typical defects are discussed along with 1D analytical and multi-dimensional numerical solutions. Special emphasis is focused on defect characterization by the use of inverse solutions. A list of TNDT terms is provided. Applications of active TNDT, mainly in the aerospace industry, are discussed briefly, and some trends in the further development of this technique are described.     

Analysis of an extensive measurement program developed from the start up to the follow up of the operation of the CNAAA NPP

Integrated tests (IT) applied to the Units I and II of the CNAAA Nuclear Power Plants (Angra dos Reis, Rio de Janeiro, Brazil) vara part of a comprehensive test program required to have the commercial operational licence issued. The IT cover operation at zero power and the subsequent power levels (the power escalation) until the nominal power operation.

This paper reports and compares the results of systematic neutron and gamma equivalent dose-rate measurements performed inside and outside the reactor containment of each Unit, during the start-up phase of the operation, for different power levels of the reactors. It also compares the collective-doses measured along the operation of the two units of the CNAAA wich similar data of the Grafenrheinfeld nuclear power plant (Germany) — basic-of-project for the CNAAA — Unit II — and analyses the data under the fight of the state-of-art.     

高性能调度技术中应用程序调度模型设计--地理空间信息网格调度技术的研究

地理空间信息网格调度技术，要比传统的高性能计算中的调度技术复杂，原因是如果将全部网格资源作为一个应用程序的调度和执行目标，必将导致通信延迟、成本昂贵、执行低效等。为此，综合考虑应用程序特性、机器特性等，研究设计了地理空间信息网格高性能调度技术中的应用程序调度模型，包括地理空间信息网格应用程序分析；资源特性分析；应用程序分解；性能预测；资源调度；机器选择；任务映射；任务调度；任务调度器和调度器管理模块。以实现为不同的应用程序匹配不同的计算资源，提高计算资源的利用率和应用程序的执行效率。     

船闸直立墙基坑开挖与锚固施工程序

三峡船闸深槽开挖与锚固工程量大，工期紧，施工强度高，施工难度大。因此，合理的施工程序有利于边坡稳定和施工，是快速和高质量施工的关键。分析了永久船闸直立墙基坑开挖与锚固施工程序的复杂性和进行研究的必要性。介绍了设计阶段研究船闸开挖与锚固的施工程序。对施工过程中研究施工程序时考虑的因素，研究的主要内容以及实际采用的施工程序作了简要的分析，归纳和总结。     

Influence of accelerated ageing on methacrylate‐based denture resins heterogeneity as viewed by ESR‐spin‐probe method

The electron‐spin‐resonance (ESR) spin‐probe method, was used to study the heterogeneity of denture resins based on poly(methyl methacrylate). Results for three resins processed by microwave energy, conventional curing and cold curing (depending on the curing procedure and exposed to ageing in various environmental conditions) were compared. All three cured resins were stored over the same time (1200 h) in distilled water at ambient temperature and in artificial saliva at 348 K. The temperature‐dependent ESR spectra of a spin probe dispersed in the denture resins are analyzed in terms of line‐shapes and line‐widths. The appearance of two spectral components was taken as an indication of resin heterogeneity. The results reveal that the cold‐cured resin has a lower local density in comparison with microwave and conventionally cured resin. The amount of residual monomer also contributes to the local motion of polymer segments. The change of denture resins exposed to ageing is influenced both by the structure of the original resin and the ageing conditions. Restricted motion of a spin probe incorporated into the acrylic resins exposed to accelerated ageing suggests additional crosslinking of polymer chains. The differences are observed for all the investigated resins, but the highest change is observed with the cold‐cured resin. The ESR results are accompanied by T_g and T_m measurements. Copyright © 2005 Society of Chemical Industry     

美国国家公园申报准则及审议程序

本文所讲述的是美国国家公园服务中心在评估申请提案、制定审查方案过程中所应用的各种标准和准则 ,同时也列出了一些认识、保护未列入国家公园体系中其他重要资源的途径和方法。     

Solution of a multidimensional inverse radiation problem by means of mode reduction

The Karhunen–Loève Galerkin procedure is employed to solve an inverse radiation problem of determining the time‐varying strength of a heat source, which mimics flames in a furnace, from temperature measurements in three‐dimensional participating media where radiation and conduction occur simultaneously. The inverse radiation problem is solved through the minimization of a performance function, which is expressed by the sum of square residuals between calculated and observed temperature, using a conjugate gradient method. Through the Karhunen–Loève Galerkin procedure, one can represent the system dynamics with a minimum degree of freedom, and consequently the amount of computation required in the solution of the inverse problem is reduced drastically when the present technique is adopted. Copyright © 2004 John Wiley & Sons, Ltd.     

A direct estimate of JIc from the load versus load-line displacement record

The purpose of this study is to examine the current standard fracture toughness test procedure to determine if there could be an easier method to get a J_Ic value from the test record. The current method for determining J_Ic involves a detailed computational and construction procedure. The objective in this study is to simplify the analysis for the determination of J_Ic. The results of this study show that the load and displacement record for a fracture toughness test can be used to directly estimate a J_Q value, a provisional value for fracture toughness, J_Ic. The J value taken at the maximum load point can be used along with an adjustment factor to estimate a J_Q value. This J_Q estimate is close to the one obtained from the construction procedure of ASTM Standard E 1820. When a unit‐sized specimen is tested, that is, a specimen with a width of 50 mm and a thickness of 25 mm the maximum load point provides a direct estimate of J_Q. Other sizes require a size adjustment factor, which is simply a square root relationship between the width of the test specimen and a unit width. The proposed new method of estimating J_Q is simple in concept and requires a minimum number of calculations. It appears to produce values of J_Q which are comparable to those obtained from the ASTM E1820 construction procedure and may produce less scatter.     

Minimizing sample evaporation in the environmental scanning electron microscope

The ElectroScan environmental scanning electron microscope (ESEM) enables wet samples to be observed by eliminating air but allowing water vapour into the sample chamber. However, evaporation from, and condensation on, the sample may occur during the pumpdown sequence used to reach this state, which means that the sample may not be in its natural state when viewed if due care is not taken. In this paper, the pumping system of the ESEM is described mathematically and expressions are derived for the evaporation and condensation. This treatment is then used to calculate the optimum pumpdown sequence. The importance of using the optimized procedure is illustrated by micrographs of fat emulsions.