Fatigue life improvement of 12Cr1МoV steel by irradiation with Zr+ ion beam

Cyclic tension and bend tests were performed on heat-resistant 12Cr1MoV steel specimens in as-supplied condition as well as after Zr⁺ ion beam surface irradiation. Distinct differences in strain induced relief, as well in cracking pattern of modified surface layer were observed by optical microscopy and interference profilometry. Changes in subsurface layer are characterized by means of nano- and microindentation and fractography of fracture surfaces (with the help of scanning electron microscopy). It is shown that the main influence on mechanical properties is mostly induced by thermal treatment during irradiation rather than formation of a 2 μm thick layer doped with Zr. The differences in deformation behavior may be explained by physical mesomechanics concepts.     

Temperature cycling and its effect on mechanical behaviours of highporosity chalks

Temperature history can have a significant effect on the strength of water-saturated chalk.In this study,hydrostatic stress cycles are applied to understand the mechanical response of chalk samples exposed to temperature cycling between each stress cycle,compared to the samples tested at a constant temperature.The total accumulated strain during a stress cycle and the irreversible strain are reported.Chalk samples from Kansas(USA)and Mons(Belgium),with different degrees of induration(i.e.amount of contact cementation),were used.The samples were saturated with equilibrated water(polar)and nonpolar Isopar H oil to quantify water weakening.All samples tested during 10 stress cycles with varying temperature(i.e.temperature cycled in between each stress cycle)accumulated more strain than those tested at constant temperatures.All the stress cycles were performed at 30℃.The two chalk types behaved similarly when saturated with Isopar H oil,but differently when saturated with water.When saturated with water,the stronger Kansas chalk accumulated more total strain and more irreversible strain within each stress cycle than the weaker Mons chalk.     

Suitability,efficiency and microbiological safety of novel physical technologies for the processing of ready‐to‐eat meals,meats and pumpable products

Consumer studies and market reports show an increase in consumption of ready‐to‐eat (RTE) foods. Although conventional processing technologies can in most cases produce safe products, they can also lead to the degradation of nutritional compounds and negatively affect quality characteristics. Consumers strongly prefer food that is minimally processed with the maximum amount of health‐promoting substances. Novel processing technologies as pre‐ or post‐treatment decontamination methods or as substitutes of conventional technologies have the potential to produce foods that are safe, rich in nutrient content and with superior organoleptic properties. Combining novel with conventional processes can eliminate potential drawbacks of novel technologies. This review examines available scientific information and critically evaluates the suitability and efficiency of various novel thermal and nonthermal technologies in terms of microbial safety, quality as well as nutrient content on the production of RTE meals, meats and pumpable products.     

埋地管道在冻土带的热力变形分析

埋地油气管道通过永冻土地带时,由于管内介质与周围的冻土发生了热力作用,使冰土解冻,在管道周围形成融化圈。文章分析了永冻土的特点,建立了永冻土地带土壤传热数学模型:融化圈内外传热方程、管道向土壤和土壤表面向大气所放热量的守恒关系、融化圈界面处土壤温度、相变界面处固相变为液相的传热条件。还建立了埋地管道模型,并以穿过永冻土地带土壤的输油管道为例,分析并计算了各种应力的最大值所在的位置和大小,提出了在永冻土地带减小管道热力变形的措施。     

油藏演化的两个极端过程

油气藏形成之后，在地质务件变化不大的情况下，储集层中的油气一般保持相对的稳定。但当地质条件变化较大时，油气藏中则发生明显的蚀变。其中两个极端的演化过程，一是抬升破坏形成生物降解沥青，一是深埋发生原油裂解转化成焦沥青和天然气。生物降解沥青没有一定的形态．在显微镜下呈席状分布，沥青反射率低，抽提物具有明显的生物降解特征。原油裂解形成的焦沥青具有一定的几何形态，沥青反射率很高而无常规抽提物。原油裂解生成的天然气在组分和碳同位素特征上与干酪根裂解生成的天然气有别。图6参15     

ca油田稠油油藏系统保护油气层研究

针对ca油田多层状砂泥薄互层稠油油藏的特点,开展了热采和非热采条件下储层变化特征研究、钻井和固井过程入井液的研究、采油工艺技术等系统保护油气层研究,了解各种变化的作用过程和原因,有效地预防现场施工中可能发生的储层伤害,从而达到储层保护、提高采收率的目的。     

催化裂解多产丙烯新技术

介绍了国内外利用蜡油或常压渣油等重质原料的增产丙烯技术CPP,ARGG FDFCC和TSRMP;还介绍了利用富含烯烃的混合碳四和催化裂化汽油等轻质原料的增产丙烯技术OCP,Propylur,Superflex,OCT,Meta-4和BASF公司的丁烯歧化工艺技术.     

新设备技术在催化裂化装置上的应用

文章介绍了近年来在催化裂化装置上应用的新设备、新技术,如BY型旋风分离器、BSX型旋分式三级旋风分离器、上下拱型三级旋风分离器、下拱型三级旋风分离器、SHS“自蔓延”技术、SWY外取热器、BWJ型喷嘴、自流浇注料、Actehem高耐磨衬里、弓形钢丝纤维、侧拉环锚固钉、分体可拆人孔等的结构特点及实际应用情况。