Waveguide external cavity narrow linewidth semiconductor lasers

Narrow linewidth light source is a prerequisite for high-performance coherent optical communication and sensing.Waveguide-based external cavity narrow linewidth semiconductor lasers(WEC-NLSLs)have become a competitive and attractive candidate for many coherent applications due to their small size,volume,low energy consumption,low cost and the ability to integrate with other optical components.In this paper,we present an overview of WEC-NLSLs from their required technologies to the state-of-the-art progress.Moreover,we highlight the common problems occurring to current WEC-NLSLs and show the possible approaches to resolving the issues.Finally,we present the possible development directions for the next phase and hope this review will be beneficial to the advancements of WEC-NLSLs.     

定距螺旋桨对船用主机外特性的要求分析

为解决定距螺旋桨与船用主机在船舶运行工况的机桨匹配问题,结合船舶系泊和航行试验的相关标准,分析和归纳船舶运行数据,将实船测试与船机桨匹配理论计算相结合,得出运输船和拖轮在常用工况及特殊工况下定距螺旋桨对主机外特性的定量要求,为配套不同细分市场时船用主机的优化和开发提供参考依据。     

大直径平底负压容器优化设计

通过对大直径平底负压容器平底板的设计计算,平底板计算厚度很厚。通过分析,提出了对平底板采取加强措施,从而减薄平底板计算厚度的方法。该容器在实际生产过程中性能可靠、稳定,对类似设备设计具有借鉴意义。     

移动通信系统中功率控制研究

在阐述功率控制在移动通信系统中的发展过程的基础上，着重研究了WCDMA系统的功率控制，最后对功率控制未来的研究方向做了简要的分析。     

国产风机盘管空调系统常见问题分析

分析了国产风机盘管使用中常见的问题,指出机组因风量不足、冷量风量匹配不合理以及风机盘管某些设备故障,导致了风机盘管精度低、舒适性差、能耗高等一系列问题。指出应引起空调设计和运行维护人员的注意。     

A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.     

简易炉外处理在电炉钢生产中的应用

阐述了小电炉采用投资少，见较快，简单易行的炉外处理措施，提高了钢质量和生产率，生产实践和应用结果表明，本措施可为同类型企业的炼钢工艺完善和技术进步提供参考。     

外循环型鼓泡式反应器气含率及循环液速率

对直径２８０ｍｍ、扩大直径５００ｍｍ、外循环管直径６５ｍｍ、总高２９００ｍｍ的外循环型鼓泡式反应器，在气体空塔线速Ｕｇ为０．０４－０．５５ｍ／ｓ时，用静压差法和脉冲示踪法测定了不同部位的气含率Ｅｇ，Ｅｐｇ和循环液速率ｕ１，并获得了它们的关联式：对反应段，Ｅｇ＝０．４５５６Ｕ＾０．３１９８ｇ〔Ｕｇ／（Ｕｇ＋Ｕ１）〕＾０．７３９６；对反应器扩大段，Ｅｕｇ＝０．９３８９Ｕ＾０．４４３１ｕｇ；对循环管，Ｅ     

On-line mass spectrometry system for measurements at single-crystal electrodes in hanging meniscus configuration

We present the construction and some first applications of an On-line electrochemical mass spectrometry system for detecting volatile products formed during electrochemical reactions at a single-crystal electrode in hanging meniscus configuration. The system is based on a small inlet tip made of porous Teflon and a Peek holder, which is brought in close proximity (ca. 10–20 μm) to the electrode surface. The tip is connected to the mass spectrometer by glass and metal tubing. Because of the small amount of gas entering the mass spectrometer, no differential pumping is needed during the measurement. The tip construction and preparation introduced here leads to reproducible voltammetry with very good cleanliness characteristics. The presence of the tip has no significant influence on the blank voltammetry of a Pt(111) in sulfuric acid, and on voltammetric responses for CO adlayer oxidation, methanol oxidation, and hydroxylamine electrochemistry on Pt(111). The formation of gaseous products in these reactions can be followed accurately and is in good agreement with earlier results obtained by other mass spectrometric or spectroscopic techniques. The time response and tailing of the setup is on the order of seconds and mainly determined by the distance between the tip and the electrode.