Freeze-drying and mechanical redispersion of aqueous PEDOT:PSS

Poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) films are attracting famous applications in antistatic coating, energy storage and conversion, printed electronics, and biomedical fields due to their conductivity, optical transparency and flexibility. However, PEDOT:PSS has poor dispersion stability during long-term storage and transport. Moreover, the dried PEDOT:PSS films are insoluble in any solvent and cannot be redispersed again. In comparison to bake drying, here, a feasible strategy to achieve mechanically redispersed PEDOT:PSS with the help of freeze-drying process was reported. The redispersed PEDOT:PSS can recover not only the initial characters such as pH, chemical composition, viscosity, and particle size under similar solid contents, but also conductivity and surface morphology of treated films. In addition, the treated film exhibits self-healing properties similar to pristine film in terms of mechanical and electrical properties. This technology enables reuse and overcomes the technical problems of PEDOT:PSS dispersion, realizing real-time processing to meet variable applications.     

Coil‐Type Asymmetric Supercapacitor Electrical Cables

Cable‐shaped supercapacitors (SCs) have recently aroused significant attention due to their attractive properties such as small size, lightweight, and bendability. Current cable‐shaped SCs have symmetric device configuration. However, if an asymmetric design is used in cable‐shaped supercapacitors, they would become more attractive due to broader cell operation voltages, which results in higher energy densities. Here, a novel coil‐type asymmetric supercapacitor electrical cable (CASEC) is reported with enhanced cell operation voltage and extraordinary mechanical‐electrochemical stability. The CASECs show excellent charge–discharge profiles, extraordinary rate capability (95.4%), high energy density (0.85 mWh cm⁻³), remarkable flexibility and bendability, and superior bending cycle stability (≈93.0% after 4000 cycles at different bending states). In addition, the CASECs not only exhibit the capability to store energy but also to transmit electricity simultaneously and independently. The integrated electrical conduction and storage capability of CASECS offer many potential applications in solar energy storage and electronic gadgets.     

Adaptive robust boundary control of shaft vibrations under perturbations with unknown upper bounds

This paper presents robust and adaptive boundary control designs to stabilize the two‐dimensional vibration of hybrid shaft model. The hybrid shaft is mathematically represented by a set of partial differential equations, governing the shaft vibrations, coupled to ordinary differential equations, describing rigid body spinning and dynamic boundary conditions. The control objective is to stabilize the transverse vibrations of the perturbed shaft while regulating the spinning rate. To achieve this, the paper first establishes robust boundary control laws that fulfil the control objective in the presence of modeling uncertainties and external disturbances operating over the shaft domain and boundary. Lyapunov‐based analyses show that the proposed robust control exponentially stabilizes the shaft with vanishing distributive perturbations, while assuring ultimately bounded vibrations in the case of nonvanishing perturbations. Then, adaptive control philosophy is utilized to achieve redesigned robust controllers that only use online adaptation of control gains without acquiring the knowledge of bounds on perturbations, as well as dynamic parameters. An advantage of this design is avoiding an overconservative robust control law, which may induce poor stability and chattering in tackling system perturbations with unknown upper bounds. Simulations through finite element method illustrate the results. Copyright © 2014 John Wiley & Sons, Ltd.     

柔性联轴节在减小转子系统扭转冲击运动中的作用

通过对大型振动磨机运动特性的研究分析,把其旋转系统简化为由两个柔性联轴节连接的三转子系统。建立了柔性连接的三转子系统在冲击转矩作用下的运动方程,对方程求解得到了柔性连接转子系统的扭转冲击响应。通过对冲击响应随柔性联轴节扭转刚度和阻尼变化规律的讨论分析,发现减小柔性联轴节的扭转刚度和增大柔性联轴节的阻尼,可以减小转子系统的扭转冲击响应。     

谐波齿轮机构在商业表格印刷机中的应用

从商业表格印刷机特殊要求出发，以某一具体机型的传动系统为例，提出采用谐波齿轮机构解决纵向套准的问题。并且分析研究了谐波齿轮机构的工作原理及其在商业表格印刷机中的使用。     

Design and Implementation of a Flexible Manufacturing Control System Using Neural Network

Design and implementation of a sequential controller based on the concept of artificial neural networks for a flexible manufacturing system are presented. The recurrent neural network (RNN) type is used for such a purpose. Contrary to the programmable controller, an RNN-based sequential controller is based on a definite mathematical model rather than depending on experience and trial and error techniques. The proposed controller is also more flexible because it is not limited by the restrictions of the finite state automata theory. Adequate guidelines of how to construct an RNN-based sequential controller are presented. These guidelines are applied to different case studies. The proposed controller is tested by simulations and real-time experiments. These tests prove the successfulness of the proposed controller performances. Theoretical as well as experimental results are presented and discussed indicating that the proposed design procedure using Elman's RNN can be effective in designing a sequential controller for event-based type manufacturing systems. In addition, the simulation results assure the effectiveness of the proposed controller to outperform the effect of noisy inputs.     

柔性桩沉降可靠性的简化分析公式

本文提出了结合分层的剪切位移法、摄动法和随机场理论来计算柔性桩沉降可靠度的简化方法，并用随机有限元和蒙特卡洛模拟法对此简化模型的精度进行了对比分析，分析结果表明该方法计算简便，精度较高。通过算例发现，在土的变形模量为小变异的情况下，其概率模型对桩的沉降可靠度影响不明显，因此其概率模型可近似采用正态分布；在土的变形模量为大变异的情况下，其概率模型对桩的沉降可靠度影响非常明显，在选择概率模型时要慎重。对于土的变形模量服从对数正态分布的情况，采用将其当量正态化后的中心点法即使在参数大变异的情况下也可以获得理想的计算精度。     

Interaction of free-surface waves with floating flexible strips

The method developed by the author to derive a set of algebaic equations to solve the interaction of free-surface waves with a single floating rigid or flexible two-dimensional platform with small draft is extended to the case that the platform consists of strips with different constant flexural rigidity and mass. The method is based on the application of Green's theorem, with a specific choice of the Green function to arrive at a differential-integral equation along the platform. This equation can be solved exactly by means of superposition of exponential functions, a standard method to solve a set of linear differential equations. After integration with respect to the space coordinate the residue theorem leads to both the dispersion relation along each individual strip and an algebraic equation for the coefficients. Due to very fast convergence with respect to the number of coefficients taken into account the series are truncated. Depending on the water-depth, in each series three to ten terms are taken into account. Results are shown for a structure consisting of several strips that are tightly connected and for disjoint strips. In the latter case the computation of the water level between the strips is also computed. The water level and the reflection and transmission coefficients are not unknowns in the algebraic equation, but are computed afterwards by means of Green's theorem.     

A new FMS architecture based upon networked DSP servo technology

This paper presents a critical evaluation of existing FMS architectures and the academic and industrial design and development strategies used during their formulation. The paper seeks to address the need for, and value of, existing architectures within the industrial arena. More importantly however, this paper puts forward a new two-tier distributed control architecture for FMS based upon new (real-time) networkable DSP servo control methodologies developed by one of the authors for Softronics in Australia. The ramifications of these methodologies are substantial, not only in terms of FMS control, but in the overall simplification of such systems and the development of flexible fixturing devices over the coming decade. This paper also postulates on how new FMS architectures can be developed from such technologies and details why such architectures could be more appropriate to industry needs than those that are currently in existence.