硼酸铝晶须增强环氧树脂和双马来酰亚胺树脂体系的研究

本文以硼酸铝晶须为增强剂，以4，5-环氧环己烷-1，2-二甲酸二缩水甘油酯(TDE-85)，甲基纳狄克酸酐(MNA)、N，N’-二胺基二苯甲烷型双马来酰亚胺(BMI)/O，O′-二烯丙基双酚A(BA)体系分别作为基体制备晶须增强复合材料。研究了晶须对树脂的尺寸、表面处理方法、含量对树脂体系力学性能和热性能的影响；通过扫描电子显微镜(SEM)分析了浇注体的弯曲、冲击断口，研究晶须的增强机理。     

β放射性气体浓度计的新分度方法

本文介绍β放射性气体浓度计的一种新的分度方法——泄漏元件排气法。其特点是一只元件可分度放射性气体浓度计的许多读出数(甚至是几个量程),操作方便。     

空间激光通信系统精跟踪单元PZT驱动电源的设计

压电陶瓷驱动电源是压电陶瓷微位移器应用中的关键部件。PA85是一种高电压、高功率MOSFET的带宽运算放大器,采用双电源供电,输出电流高达200mA,输出电压更可高达±215V。该文详细介绍了基于PA85的一种电源复合放大器的设计及仿真,通过对各项性能指标的仿真表明,该驱动电源具有精度高、分辨率高、稳定性好、纹波小和电路结构简单等优点。     

FTIR investigation of ethylene coordination and polymerization on reduced Cr/SiO2 catalyst

FTIR spectroscopy was applied to study the initial steps of ethylene polymerization on reduced chromia-silica (0.5 wt% Cr/SiO₂). To decrease the speed of the reaction small doses of gas were introduced to the catalyst in each run and C₂D₄ was used to confirm band assignments. At the initial steps of the reaction only ethylene molecules coordinated to probably Cr _A ²⁺ cations were observed. The concentration of such complexes was estimated to be about 50% of the total amount of Cr atoms in the sample. The FTIR spectrum of the polymer formed at the initial doses of C₂H₄ (when [C₂H₄] [Cr]) was found to be slightly different from that formed after excess ethylene was introduced onto the catalyst ([C₂H₄] > [Cr]).     

利用高铝矾土研制低温耐磨氧化铝瓷

着重介绍了以高铝矾土为主要原料的85瓷的合理配方和所采用的生产工艺，并对吸水率、体积密度、耐磨性、显微硬度、抗折强度和断裂韧性等物理性能进行了测试。还探讨了低温烧成机理、提高耐磨性的途径。结合显微结构分析了生产工艺对产品性能的影响。     

TDE-85环氧树脂丙烯酸酯的合成及其UV固化特性的研究

本文研究了TDE-85环氧树脂丙烯酸酯的合成方法，讨论了合成条件（催化剂的种类与用量，反应温度及时间，投料比，反应类型及不饱和酸种类的选择等）对合成反应及合成产物性状的影响。另外，还考察了该合成产物的UV固化特性。     

ZA85镁合金压铸工艺的研究

研究了压射比压、浇注温度、模具温度三个压铸工艺参数对ZA85镁合金显微组织、铸造性能和力学性能的影响,探明了其在冷室压铸条件下的最佳工艺,简单分析了压铸态组织,并成功的实现了镁合金汽车零件的试制。     

Crystallization and microstructure evolution of amorphous Al85Y4Nd4Ni7 alloy

The mixture model of Al85Y4Nd4Ni7 alloy in which a partially crystallized amorphous alloy is regarded as a nanocomposite of an Al nanoparticle and a remaining amorphous matrix is presented. Its evolution in the process of crystallization has been investigated by differential scanning calorimetry (DSC), X-ray diffraction (XRD), and transmission electron microscopy (TEM). Mainly amorphous structure with α-Al nanocrystals embedded in the amorphous matrix has been revealed by melt spining the alloy. Crystallization is showed to occur in three stages: (I) crystallization of amorphous alloy and formation of A1NiY, A1NdNi and unknown crystalline phases, (2) formation of Al3Y and Al3Nd, and (3) formation of Al3Ni.     

Oxidation behavior of temary Fe- 15Cu-5Al and Fe-85Cu-5Al alloys in pure oxygen at 900℃

The oxidation of two two-phase ternary Fe-Cu-Al alloys containing about 5%（mole fraction） aluminium, one Fe-rich and one Cu-rich, has been studied at 900 ℃ in 1~105 Pa pure oxygen. The Fe-rich Fe-15Cu-5Al alloy presents two quasi-parabolic stages, with a large decrease of the parabolic rate constant after about 50min. The presence of 5% Al greatly reduces the oxidation rate of this alloy with respect to a binary Fe-Cu alloy of similar composition by forming an external protective Al203 layer, which is present near the scale/alloy interface. Due to the high stress-growth effect, this thin Al203 layer cannot completely prevent further oxidation of the alloy underneath. On the contrary, the Cu-rich Fe-85Cu-5Al alloy presents a single parabolic stage and forms a thick and porous external scale, coupled to the internal oxidation of Fe and Al. As a result, the oxidation of Cu-rich alloy at 900 ℃ is much faster than that of the Fe-rich alloy.     

On several concepts for ɛ-efficiency

We introduce two new concepts for?-efficiency and investigate these and some known concepts under the following aspects: (1) What are the relationships between the efficient and the?-efficient point set? (2) If the sequence (v ^?) of?-efficient points converges forε → 0, is the limit efficient, or weakly efficient? (3) Can the distance between the?-efficient and the efficient point set be estimated in terms ofε?