磨料有序排布电镀砂轮的制备及其把持力研究

为解决电镀砂轮磨削加工中容屑空间不足的问题，采用点胶微粘接的方法制备了磨料有序排布的电镀砂轮，分析了磨料粘接效果和镀层力学性能。通过SEM分析了磨料/镀层/导电胶的结合界面，并进行了干磨削试验。研究结果表明，直径约为磨料粒径40%的胶点可粘接住磨料，单个胶点上粘接多颗磨料的占比小于6%；双脉冲电镀工艺制备的镀层显微硬度大于500HV，表层残余应力小于100MPa，磨料/镀层/导电胶之间的界面贴合紧密，无明显缺陷；砂轮在磨削时没有出现磨料脱落现象。     

Study on the non-uniform contact during ELID groove grinding

This paper introduces the potential feasibility that ELID (electrolytic in-process dressing) grinding replaces superfinishing in bearing manufacturing, but ELID grinding will bring new challenges. Different regions present distinguish surface profile due to the non-uniform contact in ELID groove grinding. However, few reports explaining the non-uniform contact are available. This article explores the mechanisms of the non-uniform contact during ELID groove grinding. Experiments on the non-uniform contact between bearing raceway and grinding wheel have been carried out under different conditions. The results show that non-uniform contact exists in ELID groove grinding process and it exerts influence on the profile of the raceway surface. Non-uniform contact influences the Rsk and Rku value all the time, but it influences the Ra value occasionally. Improvement strategies of eliminating the non-uniform contact are also discussed based on the experimental study.     

无油润滑压缩机活塞环和支承环设计

通过对填充聚四氟乙烯材料活塞环及带卸荷槽结构支承环的研究 ,确定了活塞及活塞环结构 ,建立了带卸荷槽支承环的力学分析模型 ,并将其结果用于结构尺寸的确定。在压缩机工艺指标不变的情况下 ,用该方法设计的活塞环和支承环性能优良。     

无掩模激光干涉光刻技术研究

介绍了一种不用掩模的光刻技术———激光干涉光刻技术的基本原理,给出了干涉光刻技术的主要特点及一些可能的应用,并对实验系统和初步实验结果进行了分析。研究表明,激光干涉光刻具有大视场和分辨率高和视场宽等优点。     

Influence of Edible Films upon the Moisture Loss and Microstructure of Dietetic Sucrose-Free Sponge Cakes during Storage

The kinetics of changes in the bound water content in dietetic sucrose-free sponge cakes (DC) during storage was investigated. The effect of edible films of polymyxan, pectin, xanthan, and carboxymethylcellulose upon this kinetics was also investigated. The quantitative changes in both states of water (slightly bound water and strongly bound water) were registered by combined dynamic analysis (thermogravimetry analysis, TGA, and differential thermal analysis, DTA). The moisture changes in DC crumb were analyzed by drying out to constant mass. The rate constants were determined according the equation q = q_oe^-kt. The values of rate constants 'k', in day^-1, concerning the different edible films were as follows: for crumb moisture is (8.00 ≤ k ≤ 12.47) × 10^-3, for bound water is (3.07 ≤ k_w ≤ 6.26) × 10^-2, for slightly bound water is (4.22 ≤ k₁ ≤ 8.49) × 10^-2 and for strongly bound water is (2.02 ≤ k₂ ≤ 5.62) × 10^-2 as compared to 18.53 × 10^-3, 7.16 × 10^-2, 9.04 × 10^-2, and 5.36 × 10^-2 in the uncovered DC, respectively. The best water-retaining effect in respect to crumb moisture during storage was ascertained in the use of polymyxan and xanthan films. The lowest rate constant values for bound water and its two states were measured for DC covered with pectin. The relation between the kinetics of both bound water states during storage and ageing of the crumb of DC covered with different edible films and the crumb microstructure was represented. By means of scanning electron microscope was read the smallest change in crumb microstructure of pectin-covered DC on the sixth day of storage.     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

提高超小型铝电解电容器生产一次合格率

恰当选择原材料、确保铆接工序质量、重视工作电解液的配比、严控各工序成品率是提高超小型铝电解电容器投入产出一次合格率的关键。以１０Ｖ－４７μＦ（４ｍｍ×７ｍｍ）产品为例，投入产出一次合格率达９４％以上。     

成形磨削中砂轮修整精度的研究

成形磨削一般采用金刚石笔来修整所需要的砂轮形状，金刚石笔在安装中的位置误差将影响被加工工件的精度，本文对此误差的大小进行了分析。     

无粘结预应力蛋形消化池的施工技术

石家庄市桥东污水处理厂有6座11500m3无粘结预应力混凝土蛋形消化池,本文介绍其非预应力钢筋、模板体系、混凝土和预应力工程等结构施工成套技术。     

在线磨辊辊面粗糙度的实验研究

影响轧辊表面粗糙度的因素很多，为此对影响辊面粗糙度的因素进行了系统分析和实验研究，得出了轧辊和砂轮的速度、砂轮粒度、砂轮直径及磨削液等主要因素对轧辊表面粗糙度影响的一般规律。利用回归分析的方法建立了轧辊表面粗糙度的数学模型，并将计算值与实测值进行了比较，发现两者基本一致。此项研究为适时控制冷轧带钢在线磨辊辊面粗糙度提供了计算模型。