金属油罐的渗漏与修复

分析了金属油罐渗漏的部位及原因，根据实际情况采取不同的方法进行修复。     

An Experimental Investigation into the Feed Rate Capacity of Rotary Valve and Blow Tank Feeders

Industry widely uses rotary valves and blow tanks for the pneumatic conveying of products, each having their pros and cons depending on the specific application. This article shows the differing results obtained when low-velocity conveying a product through a common pipeline using both a drop-through rotary valve and a bottom-discharge blow tank feeder. A number of issues arise in the rotary valve system, the main one being rotary valve air leakage. A blow tank system, on the other hand, does not leak, as it is an enclosed system. The experimental results show dramatic differences in product throughput. Further exploration leads to a novel modification being made to the rotary valve system in an attempt to increase its capacity. The result of this modification shows a slight increase in output tonnage, but still significantly less than that obtained from the blow tank.     

In Situ Performance Testing of Deteriorating Water Tanks for Durability Assessment

Reports of failure of existing concrete structures due to a lack of durability, rather than a deficiency in structural strength, has made concrete technologists, engineers, and researchers focus research on the parameters influencing durability performance with respect to time. Systematic performance monitoring, with respect to chosen durability parameters of existing concrete structures, will decide the direction of future research in this area. Inferences based on laboratory simulations and testing need to be confirmed by in situ field measurements and studies. In situ condition rating and performance monitoring surveys have been conducted by many researchers, scientists, and professional associations, and reported in literature. Inferences of few such studies are summarized and discussed. Deterioration of concrete structures constructed in recent times is observed at relatively faster rates, and has been mainly attributed to cracking. Cracking is associated with the use of faster-hydrating portland cements with increased fineness and the tricalcium silicate (C3S) content to support the high speed of modern construction. In the present research, a case study of deteriorated water tank structures situated in the semitropical region of India is presented. Some selected parameters—such as concrete cover, carbonation depth, chloride concentration, compressive strength, etc. which influence long term durability of structures—have been measured.     

块状岩体台阶爆破炮孔填塞作用的研究

本文利用电磁测量法及高速摄影法对块状模型中炮孔填塞物在孔内的运动规律和块体移动过程进行了研究。根据模拟试验及一些生产爆破的观测结果，对炮孔填塞机理提出了一些新的观点；同时就露天矿台阶爆破炮孔填塞长度及材料对爆破效果的影响作了简要分析。     

粘接技术在油罐堵漏中的应用

介绍了粘接技术的种类、原理及其技术要领，并引用实例说明了该技术的优点。粘接堵漏技术将成为油罐渗漏维修的一种重要方法。     

大型钢制立式储罐的导链式倒装法施工

介绍了导链式倒装法安装大型钢制立式储罐的原理及制作工艺流程。     

深大露天矿综合开采工艺主要设计参数的研究

深大露天矿的间断向半连续开采工艺过渡时，合理深度及半连续开采工艺的移设步距是两个重要的开采参数，对矿山的经济效果影响巨大，本文首次提出采用组合台阶单位体的开采来分析确定这两个重要的参数，得到的结论在霍林河煤矿的应用中取得了满意的结果，对其它类似矿山具有应用价值。     

胜利油田污水储罐腐蚀防护方法评价

对胜利油田纯粱采油厂A3钢制生产污水（水温约60℃）储罐使用寿命过低的原因进行了实验考察。水质分析数据表明氯离子浓度高（45-48gm）是污水腐蚀性强的主要因素。A3钢在60℃污水中的腐蚀速率，由极化曲线数据计算的值大大高于失重法测定值，敞开系统中失重法测定值又高于密闭系统中测定值，挂片上出现蚀孔，说明储罐中A3钢发生了氧存在下氟离子引起的局部腐蚀（孔蚀）。元素分析结果表明．储罐阴极保护所用的牺牲阳极铝材含铁等元素量超标。牺牲阳极密封不良，在实验污水中7天后电流效率仅为2．92％，失去阴极保护能力。处于实验污水环境中的有涂层保护的A3钢．14天后出现腐蚀极化电流，表明涂层已失去完整性。要提高该采油厂及胜利油田其他采油厂污水储罐的使用寿命，必须改用合格的牺牲阳极和保护涂层材料。图3表2参7。     

油罐冒罐事故的原因分析及预防

通过事故实例分析，阐述油罐冒罐事故的原因，并针对原因提出要加强操作人员的责任心教育，完善各项规章制度，不断提高操作人员素质，严格遵守岗位操作规程，及时消除设备缺陷、完善罐区硬件设施和罐区实行现代科学管理等项措施。