Synthesis,characterization and charge transport properties of Pr–Ni Co-doped SrFe2O4 spinel for high frequency devices applications

Ferrites are materials of interest due to their broad applications in high technological devices and a lot of research has been focused to synthesize new ferrites. In this regard, an effort has been devoted to synthesize spinel Pr–Ni co-substituted strontium ferrites with a nominal formula of Sr_1-xPr_xFe_2-yNi_yO₄ (0.0 ≤ x ≤ 0.1, 0.0 ≤ y ≤ 1.0). The cubic structure of pure and Pr–Ni co-substituted strontium ferrite samples calcinated at 1073 K for 3 h has been confirmed through X-ray diffraction (XRD). Average sizes of crystallites (18–25 nm) have been estimated from XRD analysis and nanometer particle sizes of synthesized ferrites have been further verified by scanning electron microscopy (SEM). SEM results have also shown that particles are mostly agglomerated and all the samples possess porosity. It has been observed that at 298 K, the values of resistivity (ρ) increase, while that of AC conductivity, dielectric loss, and dielectric constants decrease with increasing amounts of Pr³⁺ and Ni²⁺ ions. The values of dielectric parameters initially decrease with frequency and later become constant and can be explained on the basis of dielectric polarization. Electrochemical impedance spectroscopy (EIS) studies show that the charge transport phenomenon in ferrite materials is mainly controlled via grain boundaries. Overall, synthesized ferrite materials own enhanced resistivity values in the range of 1.38 × 10⁹–1.94 × 10⁹ Ω cm and minimum dielectric losses, which makes them suitable candidates for high frequency devices applications.     

Three-phase four-wire shunt active power filter based on the SOGI filter and Lyapunov function for DC bus control

The three-phase four-wire shunt active power filter (SAPF) was developed to suppress the harmonic currents generated by nonlinear loads, and for the compensation of unbalanced nonlinear load currents, reactive power, and the harmonic neutral current. In this work, we consider instantaneous reactive power theory (PQ theory) for reference current identification based on the following two algorithms: the classic low-pass filter (LPF) and the second-order generalized integrator (SOGI) filter. Furthermore, since an important process in SAPF control is the regulation of the DC bus voltage at the capacitor, a new controller based on the Lyapunov function is also proposed. A complete simulation of the resultant active filtering system confirms its validity, which uses the SOGI filter to extract the reference currents from the distorted line currents, compared with the traditional PQ theory based on LPF. In addition, the simulation performed also demonstrates the superiority of the proposed approach, for DC bus voltage control based on the Lyapunov function, compared with the traditional proportional-integral (PI) controller. Both novel approaches contribute towards an improvement in the overall performance of the system, which consists of a small rise and settling time, a very low or nonexistent overshoot, and the minimization of the total harmonic distortion (THD).     

浅谈DC/DC变换器控制新方法

文中针对DC/DC变换器的特点,在现有控制和建模方法的基础之上,对DC/DC变换器的现代控制方法进行了归纳和总结,简要讨论了其控制原理,并比较了各种现代控制方法的优缺点,最后对DC/DC变换器控制方法的发展作了一定的展望。     

直流电动机参数测定

根据直流电机的可逆原理并利用常规的实验仪表，可以简便、准确地测出直流电动机的主要参数－电磁转矩、输出转矩和效率．     

LM2717型双降压直流/直流变换器的原理及其应用设计

LM2717是美国国家半导体公司推出的一款全新的高性能变换器,内含两个脉宽调制(PWM)直流/直流转换器,功能强大.介绍了该器件的主要参数、工作原理和引脚功能,讨论利用LM2717进行应用设计时选择外部器件的原则及设计中应注意的问题.     

TOPSwitch集成电路在DC/DC电源设计中的应用

文章介绍了PWM／MOSFET二合一的TOPSwitch系列集成电路及其在DC／DC电源设计中的应用，还介绍了基本反馈方式的DC／DC拓扑结构及其改进措施，并对由TOPSwitch集成电路构成的DC／DC电源进行了抗中子实验。     

论直流电动机换向火花的检测与调整

本文着重探讨直流电动机换向火花的形成、征状以及使用的一些对其进行判别、调整的简单方法，并阐述其原理及效果。     

电荷灵敏放大器不用反馈高值电阻的新方法

本文提出了一种电荷灵敏放大器不用反馈高值电阻的新方法。对这种方法作了电路分析以及对实际电路的测量结果作了介绍。     

20K以下温区单级脉管制冷机直流控制实验研究

开展了20K以下温区单级脉管制冷机的实验研究，考察了直流流动对制冷机性能的影响，估算了不同制冷温度下制冷机循环的需气量，在对直流进行控制的情况下，采用2kW(RW2)和4kW(CP4)压缩机分别获得了18．7K和14．7K的最低制冷温度，对应的在30K的制冷量分别为10W和29．5W。     

直流电弧炉长弧泡沫渣技术

本文指出了直流电弧炉采用长弧泡沫渣技术的必要性及该技术的发展现状，总结了炉渣物理性质，化学成分，温度和气源等对炉渣泡沫化的影响，并介绍了电炉泡沫渣的操作工艺及实际应用效果，对宝钢三期１５０ｔＤＣ－ＵＨＰ电弧炉的泡沫渣工艺提出了看法。