Synthesis,characterization and charge transport properties of Pr–Ni Co-doped SrFe2O4 spinel for high frequency devices applications

Ferrites are materials of interest due to their broad applications in high technological devices and a lot of research has been focused to synthesize new ferrites. In this regard, an effort has been devoted to synthesize spinel Pr–Ni co-substituted strontium ferrites with a nominal formula of Sr_1-xPr_xFe_2-yNi_yO₄ (0.0 ≤ x ≤ 0.1, 0.0 ≤ y ≤ 1.0). The cubic structure of pure and Pr–Ni co-substituted strontium ferrite samples calcinated at 1073 K for 3 h has been confirmed through X-ray diffraction (XRD). Average sizes of crystallites (18–25 nm) have been estimated from XRD analysis and nanometer particle sizes of synthesized ferrites have been further verified by scanning electron microscopy (SEM). SEM results have also shown that particles are mostly agglomerated and all the samples possess porosity. It has been observed that at 298 K, the values of resistivity (ρ) increase, while that of AC conductivity, dielectric loss, and dielectric constants decrease with increasing amounts of Pr³⁺ and Ni²⁺ ions. The values of dielectric parameters initially decrease with frequency and later become constant and can be explained on the basis of dielectric polarization. Electrochemical impedance spectroscopy (EIS) studies show that the charge transport phenomenon in ferrite materials is mainly controlled via grain boundaries. Overall, synthesized ferrite materials own enhanced resistivity values in the range of 1.38 × 10⁹–1.94 × 10⁹ Ω cm and minimum dielectric losses, which makes them suitable candidates for high frequency devices applications.     

Integrated circuit and system design for renewable energy inverters

This study proposes that a novel integrated circuit (IC) and system design for renewable energy inverters can harvest renewable energy to power direct current (DC) and alternating current (AC) loads. In addition, an intelligent synthesis and management tool is developed to design the proposed system and to judge the system’s operational maintenance decisions. Finally, a renewable energy inverter’s information is posted to an online system. Users can obtain the proposed system’s information at any time and place. The accurate and superior performance of the proposed IC and system is confirmed by computer simulations and experimental results.     

Mímir: An open-source semantic search framework for interactive information seeking and discovery

Semantic search is gradually establishing itself as the next generation search paradigm, which meets better a wider range of information needs, as compared to traditional full-text search. At the same time, however, expanding search towards document structure and external, formal knowledge sources (e.g. LOD resources) remains challenging, especially with respect to efficiency, usability, and scalability.This paper introduces Mímir—an open-source framework for integrated semantic search over text, document structure, linguistic annotations, and formal semantic knowledge. Mímir supports complex structural queries, as well as basic keyword search.Exploratory search and sense-making are supported through information visualisation interfaces, such as co-occurrence matrices and term clouds. There is also an interactive retrieval interface, where users can save, refine, and analyse the results of a semantic search over time. The more well-studied precision-oriented information seeking searches are also well supported.The generic and extensible nature of the Mímir platform is demonstrated through three different, real-world applications, one of which required indexing and search over tens of millions of documents and fifty to hundred times as many semantic annotations. Scaling up to over 150 million documents was also accomplished, via index federation and cloud-based deployment.     

Three-phase four-wire shunt active power filter based on the SOGI filter and Lyapunov function for DC bus control

The three-phase four-wire shunt active power filter (SAPF) was developed to suppress the harmonic currents generated by nonlinear loads, and for the compensation of unbalanced nonlinear load currents, reactive power, and the harmonic neutral current. In this work, we consider instantaneous reactive power theory (PQ theory) for reference current identification based on the following two algorithms: the classic low-pass filter (LPF) and the second-order generalized integrator (SOGI) filter. Furthermore, since an important process in SAPF control is the regulation of the DC bus voltage at the capacitor, a new controller based on the Lyapunov function is also proposed. A complete simulation of the resultant active filtering system confirms its validity, which uses the SOGI filter to extract the reference currents from the distorted line currents, compared with the traditional PQ theory based on LPF. In addition, the simulation performed also demonstrates the superiority of the proposed approach, for DC bus voltage control based on the Lyapunov function, compared with the traditional proportional-integral (PI) controller. Both novel approaches contribute towards an improvement in the overall performance of the system, which consists of a small rise and settling time, a very low or nonexistent overshoot, and the minimization of the total harmonic distortion (THD).     

Material design and development: From classical thermodynamics to CALPHAD and ICME approaches

This paper presents an overview and examples of material design and development using (1) classical thermodynamics; (2) CALPHAD (calculation of phase diagrams) modeling; and (3) Integrated Computational Materials Engineering (ICME) approaches. Although the examples are given in lightweight aluminum and magnesium alloys for structural applications, the fundamental methodology and modeling principles are applicable to all materials and engineering applications. The examples in this paper have demonstrated the effectiveness and limitations of classical thermodynamics in solving specific problems (such as nucleation during solidification and solid-state precipitation in aluminum alloys). Computational thermodynamics and CALPHAD modeling, when combined with critical experimental validation, have been used to guide the selection and design of new magnesium alloys for elevated-temperature applications. The future of material design and development will be based on a holistic ICME approach. However, key challenges exist in many aspects of ICME framework, such as the lack of diffusion/mobility databases for many materials systems, limitation of current microstructural modeling capability and integration tools for simulation codes of different length scales.     

Development and monitoring of an integrated bioprocess for production of a potential malaria vaccine with Pichia pastoris

An engineered variant of the yeast Pichia pastoris was used to produce the potential malaria vaccine D1M1. This paper describes the implementation of an expanded bed adsorption chromatography step into a sequential cultivation process of the yeast in order to link protein expression, cell release, and product capture of the secreted protein in a fully automated plant. The process is operated with a semi-continuous strategy for an integrated production. Process improvements have been achieved using design of experiments. Resulting purities of product achieved up to 87% with recoveries of 51% in a single downstream operation. Furthermore, a multivariate analysis of historical batch data was used to develop a golden batch model for process monitoring.     

An effective coding approach for multiobjective integrated resource selection and operation sequences problem

In this paper, we consider an integrated Resource Selection and Operation Sequences (iRS/OS) problem in Intelligent Manufacturing System (IMS). Several kinds of objectives are taken into account, in which the makespan for orders should be minimized; workloads among machine tools should be balanced; the total transition times between machines in a local plant should also be minimized. To solve this multiobjective iRS/OS model, a new two vectors-based coding approach has been proposed to improve the efficiency by designing a chromosome containing two kinds of information, i.e., operation sequences and machine selection. Using such kind of chromosome, we adapt multistage operation-based Genetic Algorithm (moGA) to find the Pareto optimal solutions. Moreover a special technique called left-shift hillclimber has been used as one kind of local search to improve the efficiency of our algorithm. Finally, the experimental results of several iRS/OS problems indicate that our proposed approach can obtain best solutions. Further more comparing with previous approaches, moGA performs better for finding Pareto solutions. Received: May 2005/Accepted: December 2005     

浅谈DC/DC变换器控制新方法

文中针对DC/DC变换器的特点,在现有控制和建模方法的基础之上,对DC/DC变换器的现代控制方法进行了归纳和总结,简要讨论了其控制原理,并比较了各种现代控制方法的优缺点,最后对DC/DC变换器控制方法的发展作了一定的展望。     

DC/DC电源中的电磁干扰及其对策

概述了电磁干扰(EMI)和电磁兼容(EMC)的基本知识，对DC／DC电源中的电磁干扰进行了综合分析，并给出了各自的解决方案。