Progress and major BARRIERS of nanocatalyst development in direct methanol fuel cell: A review

Direct methanol fuel cells (DMFC), among the most suited and prospective alternatives for portable electronics, have lately been treated with nanotechnology. DMFCs may be able to remedy the energy security issue by having low operating temperatures, high conversion efficiencies, and minimal emission levels. Though, slow reaction kinetics are a significant restriction of DMFC, lowering efficiency and energy output. Nowadays, research is more focused on fundamental studies that are studying the factors that can improve the capacity and activity of catalysts. In DMFC, among the most widely explored catalysts are platinum and ruthenium which are enhanced in nature by the presence of supporting materials such as nanocarbons and metal oxides. As a result, this research sheds light on nanocatalyst development for DMFCs based on Platinum noble metal. To summarize, this research focuses on the structure of nanocatalysts, as well as support materials for nanocatalysts that can be 3D, 2D, 1D, or 0D. The support material described is made up of CNT, CNF, and CNW, which are the most extensively used because they improve the performance of catalysts in DMFCs. In addition, cost estimations for fuel cell technology are emphasized to show the technology's status and requirements. Finally, challenges to nanocatalyst development have been recognized, as well as future prospects, as recommendations for more innovative future research.     

Evaluation of hydrodynamic behavior of the perforated gas distributor of industrial gas phase polymerization reactor using CFD-PBM coupled model

A 2D computational fluid dynamics (Eulerian–Eulerian) multiphase flow model coupled with a population balance model (CFD-PBM) was implemented to investigate the fluidization structure in terms of entrance region in an industrial-scale gas phase fluidized bed reactor. The simulation results were compared with the industrial data, and good agreement was observed. Two cases including perforated distributor and complete sparger were applied to examine the flow structure through the bed. The parametric sensitivity analysis of time step, number of node, drag coefficient, and specularity coefficient was carried out. It was found that the results were more sensitive to the drag model. The results showed that the entrance configuration has significant effect on the flow structure. While the dead zones are created in both corners of the distributors, the perforated distributor generates more startup bubbles, heterogeneous flow field, and better gas–solid interaction above the entrance region due to jet formation.     

Damage tolerance in additively manufactured ceramic architected materials

Technical ceramics exhibit exceptional high-temperature properties, but unfortunately their extreme crack sensitivity and high melting point make it challenging to manufacture geometrically complex structures with sufficient strength and toughness. Emerging additive manufacturing technologies enable the fabrication of large-scale complex-shape artifacts with architected internal topology; when such topology can be arranged at the microscale, the defect population can be controlled, thus improving the strength of the material. Here, ceramic micro-architected materials are fabricated using direct ink writing (DIW) of an alumina nanoparticle-loaded ink, followed by sintering. After characterizing the rheology of the ink and extracting optimal processing parameters, the microstructure of the sintered structures is investigated to assess composition, density, grain size and defect population. Mechanical experiments reveal that woodpile architected materials with relative densities of 0.38–0.73 exhibit higher strength and damage tolerance than fully dense ceramics printed under identical conditions, an intriguing feature that can be attributed to topological toughening.     

Constructing developable surfaces by wrapping cones and cylinders

We model developable surfaces by wrapping a planar figure around cones and cylinders. Complicated developables can be constructed by successive mappings using cones and cylinders of different sizes and shapes. We also propose an intuitive control mechanism, which allows a user to select an arbitrary point on the planar figure and move it to a new position. Numerical techniques are then used to find a cone or cylinder that produces the required mapping. Several examples demonstrate the effectiveness of our technique.     

Metalorganic chemical vapor deposition of silver thin films for future interconnects by direct liquid injection system

Deposition of Ag films by direct liquid injection-metal organic chemical vapor deposition (DLI-MOCVD) was chosen because this preparation method allows precise control of precursor flow and prevents early decomposition of the precursor as compared to the bubbler-delivery. Silver(I)-2,2-dimethyl-6,6,7,7,8,8,8-heptafluoro-3,5-octanedionato-triethylphosphine [Ag(fod)(PEt₃)] as the precursor for Ag CVD was studied, which is liquid at 30 °C. Ag films were grown on different substrates of SiO₂/Si and TiN/Si. Argon and nitrogen/hydrogen carrier gas was used in a cold wall reactor at a pressure of 50–500 Pa with deposition temperature ranging between 220 °C and 350 °C. Ag films deposited on a TiN/Si diffusion barrier layer have favorable properties over films deposited on SiO₂/Si substrate. At lower temperature (220 °C), film growth is essentially reaction-limited on SiO₂ substrate. Significant dependence of the surface morphology on the deposition conditions exists in our experiments. According to XPS analysis pure Ag films are deposited by DLI-MOCVD at 250 °C by using argon as carrier gas.     

吸湿干爽性涤纶长丝的研制

采用德国吉玛公司直纺和日本东丽公司卷绕设备,探索差别化吸湿干爽性涤纶长丝的生产工艺。     

一种基于小波逼近的稳定直接自适应控制算法

针对一类未知不稳定非线性系统,基于小波逼近理论,提出了一种直接自适应控制 算法,并由Lyapnov理论证明了整个控制闭环系统的稳定性.     

DS1620实现的X射线采集板温度自动控制

DR是目前非常先进的X射线成像技术，将其X射线采集板工作温度控制在最佳工作范围可采集更好的图像。本系统采用PC和单独控制双模块分别控制温度，利用半导体传感器DS1620进行四路温度采集，通过单片机和PC串口通信，用PC通过半导体制冷芯片来控制X射线采集板的工作温度，在通信故障时也可以通过单独控制模块来控制采集板的温度。