凝胶渗透色谱法测定基础油PAO的相对分子质量及分布

聚α-烯烃是一种性能优良的润滑油基础油，其相对分子质量及分布直接影响宏观性能。本研究建立了一种用于表征1-癸烯齐聚物相对分子质量及分布的方法。采用带示差折光检测器的凝胶渗透色谱系统，综合考虑分离效果和测试可操作性，优化了流动相流速和凝胶色谱柱的组合方式。以四氢呋喃为流动相，流速为0.8 mL/min，色谱柱组合方式为Styragel HR 0.5,Styragel HR 1,PLGEL 3μm MIXED-E三柱串联，以聚苯乙烯作为标准样品，采用普适校正方法处理色谱流出曲线。此方法测得样品的质均相对分子质量与凝胶渗透色谱-光散射法所测定结果相比较，相对误差相对偏差在3%以内。     

Mechanical spectroscopy in commercial Fe–6 wt.% Si alloys between 400 and 1000 K

Mechanical spectroscopy, neutron diffraction and differential scanning calorimetry (DSC) were performed on commercial Fe–6 wt.% Si alloy after quenching from high temperature. The damping spectrum shows a peak at around 800 K and an associated modulus defect. The modulus shows an increase during the second and subsequent heating runs. In addition, an anomaly in the modulus behavior has been found at around 400 K. Different thermal treatments allows to obtain two different recovery degrees of the quenched-in defects. The influence of the recovery degree on the 800 K internal friction peak and on the anelastic modulus has been evaluated and confirm the validity of the grain boundary mechanism associated to this peak. Experimental results are discussed on the basis of recovery and ordering processes.     

高速往复式内燃机平衡轴低质量设计分析

分析了扇形和偏心圆两种平衡轴设计的要求以及平衡重低质量的设计原则。扇形平衡重半径及宽度应尽量大、夹角应尽量小。偏心圆平衡重的偏心圆半径应尽可能大 ,轴承半径应尽可能小。同样质量的扇形平衡重产生的平衡力比偏心圆平衡重要大。     

试论会计电算化系统的内部控制

阐述了会计电算化系统产生和发展对内产控制的影响，以及内部控制的实施方法。     

Evidence of High Vertical Wave-Number Behavior in a Continuously Stratified Reservoir: Boadella, Spain

High vertical wave-number modes clearly dominate the internal wave field during the stratification period in Boadella reservoir in northeast Spain. In this period, the extraction of hypolimnetic water, due to summer irrigation, brought the surface level down by 6 m in one month and the epilimnetic water progressively occupied the whole water column. The temperature profile, with the exception of a few meters at the surface layer, presented an almost constant temperature gradient of about 0.7°C/m. The period of the main vertical mode is 24 h with an amplitude of around 1 m. Thermistor chain records and meteorological data allow us to deduce that this mode is, at least, a third vertical mode forced by the wind, which normally has a typical periodicity of 24 h. However, when the wind changes direction from south to north, the circulation cells developed due to this forced nonstationary oscillation are destroyed. When this occurs, the Bulk Richardson number is Rib ～ 1. Similar vertical structures as a response to wind forcing should be expected in similar systems, although this has not been reported in the literature.     

基于显微视觉的宏/微双重驱动微动台的自动标定

提出了基于压电技术的微操作系统的自动标定方法,采用混合式步进电机直接驱动的宏动平台,实现系统大行程宏动定位,安装在宏动平台上的压电陶瓷驱动的微动平台和精密光栅,实现亚微米级的分辨率和定位精度,通过以上两部分实现定位机构的全闭环反馈控制,采用显微视觉反馈获取微动台操作器在图像中的位置信息进行标定。实验结果表明:系统的动态和稳定性能良好,自动标定运算速度快,运行速度达到11 frame/s,实现了对系统的精确标定,标定精度达到0.1μm。     

Exit effect on hydrodynamics of the internal circulating fluidized bed riser

This is the first time an extensive investigation has been carried out regarding the effects of riser exit geometry on pressure drop and solid behaviour inside the Internal Circulating Fluidized Bed (ICFB) riser, using different riser exit geometries at several operating conditions.The Radioactive Particle-Tracking (RPT) technique was used for solid concentration measurements and solid residence time distribution at the exit zone. Experiments were conducted using Geldart B particles, in the gas superficial velocity range of 4 to 10 m/s. Axial solid hold-up, solid residence time distribution in the exit zone, and the reflux ratio factor k_m, (defined earlier by [E.H. Van der Meer, R.B. Thorpe, J.F. Davidson, Flow patterns in the square cross-section riser of a circulating fluidized bed and the effect of riser exit design, Chem. Eng. Sc. 55 (19) (2000) 4079-4099]), were the main criteria used to investigate the impact of gas-solid separator devices implemented at the ICFB riser exit.Solid residence time distribution results and axial solid hold-up profiles provided clear evidence that the separator device at the riser exit strongly influences the hydrodynamic structure of the ICFB riser. The V-shaped riser exit geometry was found to be the optimum of all the configurations studied.     

Three dimensional boundary element analysis of internal cracks under sliding contact load with a spherical indenter

Using boundary element based three dimensional modelling for linear fracture mechanics, we present an analysis of cracking in a homogeneous medium subject to contact load. The proposed iterative solution procedure allows a simultaneous treatment of a reasonable number of partially closed cracks. It is shown that the most probable direction of propagation of a vertical internal crack is strongly dependent on its size compared to the contact radius and its location with respect to the axis of maximum normal load.     

Integrated Smart Sensor Calibration

In many applications electronic sensors are used toimprove performance and reliability of measurement systems. Suchsensors should provide a correct transfer from the physical signalto be measured to the electrical output signal. One importantstep to achieve this, is to calibrate each sensor by applyingdifferent reference input signals and adjusting the sensor transferaccordingly. Besides expensive reference equipment the calibrationprocess takes much time and attention per individual sensor,which means a considerable increase in sensor production costs.By including at the sensor or sensor interface chip a programmablecalibration facility the calibration of such smart sensors caneasily be automated and can be executed for a batch of sensorsat a time, thus minimizing the calibration time and costs. Thispaper presents a calibration method and options for integrationin the smart sensor concept, in hardware as well as in software.An advantage of the proposed method is that it does not needa large matrix of calibration data, which needs to be storedin a look-up table or converted into a correction formula, butinstead it uses a step-by-step approach to correct the sensortransfer at each calibration measurement until the error is sufficientlysmall.     

FE Simulation for Internal Inversion of Aluminium Alloy Tube

1 Introduction A double-walled invertube is difficult to fabricate other than applying inversion process. Such kind of invertube can be used as impact energy absorbing element in transport vehicles, like aircrafts and automobiles. Reddy T Y[1] did the analysis of Internal inversion and calculated the inversion load. Reid[2] et al. examined nosing and internal inversion of cold drawn steel tube by the finite element package ABAQUS. Recently, Rosa P A[3] et al. investigated Internal invers…