极限工况下的管网“互联互通”改进方案

在全国天然气管道“主干互联、区域成网”(以下简称“互联互通”)基础格局逐渐形成的背景下,天然气管网规模日益扩大、管道分支和气源增加,并且分布不集中、输送方向可变,使得输气方案更加灵活,可以更好地解决某些地域的供气紧张问题;但受现有站场和设备的限制,暂不能满足某些多线组合极限工况,使得“互联互通”的初衷难以全部实现。为了使得现有的各输气干线在实现“互联互通”之后可以满足更多的多线组合工况,在分析“互联互通”背景下M管网工况变化的基础上,研发了可以进行水力仿真和压气站方案制订的计算软件,并对3种极限工况下的不同输气量情况进行了可行性试算,进而基于试算结果提出了相应的管网改进建议。研究结果表明:(1)经验证,软件计算误差满足要求;(2)在M管道某处增设压气站或在某些输气站场配置压缩机组;(3) M管网改进调整后,可以完成大部分的多线组合极限工况,真正实现“互联互通”的输气方案。结论认为,该研究成果有助于推进全国天然气管网早日实现“互联互通”。     

A charge sharing–based switching scheme for SAR ADCs

This paper presents an energy-efficient switching scheme for successive approximation register (SAR) analogue-to-digital converter (ADC). The proposed scheme employs charge recycling method to keep the capacitor arrays free of transitional energy between bit generations except reset phase. In comparison with the conventional switching scheme, the proposed one achieves 100% transitional energy saving without considering reset phase. In addition, configuration of a 10-bit SAR ADC shows that the proposed switching scheme reduces the capacitor area by 25% compared with the conventional switching scheme.     

管道风险管理方法研究

按照管道风险管理的流程分别对管道风险评价、风险控制和决策支持、效能测试和响应进行了论述。针对目前国内管道行业的情况，提出了进行管道风险评价的有效方法及维护措施。着重介绍了国外管道风险可接受标准的情况，作为国内制定管道风险评价标准的参考。     

输油管线停输期间开泵顶管时间周期的确定

对于间断性输送高凝点石油产品 ,在停输时间较长的情况下 ,为避免油品凝结 ,需定时开泵进行顶管。为减少操作频次 ,节约能量消耗 ,通过对管线油品温降的计算和分析 ,可以比较精确地测算出输油管线温降规律 ,从而确定停输期间开泵顶管的时间周期 ,为生产实际提供理论依据     

16位串行模数转换器MAX1132的特性及应用

MAX1132是美国MAXIM公司生产的16位串行模数转换器，文章介绍了MAX1132的工作原理、接口特点及使用方法，给出了它在数据采集系统中的硬件电路和软件程序。     

基于FIF0与电平转换器的DSP高速ADC系统

给出了一种以DSP数字信号处理芯片TMS320VC5402作数据处理器，结合高速模数转换器AD9244、先进先出缓冲存储器芯片IDT7204以及电平转换器SN74ALVC164245构成的高速数据采集系统的设计方案。     

基于MAPINFO和VB的自来水管网信息系统的建立

介绍基于MapInfo平台，利用VB语言进行二次开发，建立自来水管网地理信息系统的关键技术及其注意的问题。     

An 8-bit, 200 MSPS Folding and Interpolating ADC

An 8-bit, 200 MSPS folding and interpolating analog-to-digitalconverter, ADC, has been implemented in a 1.2 µmBiCMOS-process. It achieves 7.5 effective bits with a power dissipationof 575mW. The active area is 4mm². The implementationand measured results are presented. A simple analytical modelfor the interpolation-induced nonlinearity in a folding and interpolatingADC using sinusoidal folding is presented. The bowing of thereference ladder due to interaction with the input stages isanalyzed, and analytical models are derived.     

A novel open-loop high-speed CMOS sample-and-hold

A new open-loop high-speed CMOS sample-and-hold is presented. Based on new method for further reduction of voltage-dependent charge injection, a new CMOS sample-and-hold was designed. Simulation results confirm the effectiveness of this method. Over 10 dB improvement in signal-to-noise ratio, compared to the signal-to-noise ratio of conventional bottom plate sampling S/Hs was achieved with this method. A comparison between newly designed S/H and the bottom-plate sampling S/H is presented.     

An investigation of the unstable region for dense phase conveying in sliding bed flow

For fine powdered materials, capable of being conveyed in dense phase, a conveying region exists in which instability in flow and pipeline blockage can occur if the pressure gradient available is insufficient to maintain a minimum value of solids loading ratio. A reduction in material flow rate can also lead to pipeline blockage in this region. Conveying trials under-taken with cement are used to illustrate the nature of the problem.