TEM Studies of High Temperature Corrosion Behaviour of TiAl Intermetallics with Surface Modifications

The oxidation/sulphidation behaviour of a Ti‐46.7Al‐1.9W‐0.5Si alloy with a TiAl₃ diffusion coating was studied in an environment of H₂/H₂S/H₂O at 850^oC. The kinetic results demonstrate that the TiAl₃ coating significantly increased the high temperature corrosion resistance of Ti‐46.7Al‐1.9W‐0.5Si. The SEM, EDX, XRD and TEM analysis reveals that the formation of an Al₂O₃ scale on the surface of the TiAl₃‐coated sample was responsible for the enhancement of the corroison resistance. The Ti‐46.7Al‐1.9W‐0.5Si alloy was also modified by Nb ion implantation. The Nb ion implanted and as received sampels were subjected to cyclic oxidation in an open air at 800^oC. The Nb ion implantation not only increased the oxidation resistance but also substantially improved the adhesion of scale to the substrate.     

1/f noise in large-area Hg<Subscript>1−x</Subscript>Cd<Subscript>x</Subscript>Te photodiodes

The 1/f noise in photovoltaic (PV) molecular-beam epitaxy (MBE)-grown Hg_1−xCd_xTe double-layer planar heterostructure (DLPH) large-area detectors is a critical noise component with the potential to limit sensitivity of the cross-track infrared sounder (CrIS) instrument. Therefore, an understanding of the origins and mechanisms of noise currents in these PV detectors is of great importance. Excess low-frequency noise has been measured on a number of 1000-μm-diameter active-area detectors of varying “quality” (i.e., having a wide range of I-V characteristics at 78 K). The 1/f noise was measured as a function of cut-off wavelength under illuminated conditions. For short-wave infrared (SWIR) detectors at 98 K, minimal 1/f noise was measured when the total current was dominated by diffusion with white noise spectral density in the mid-10⁻¹⁵A/Hz^1/2 range. For SWIR detectors dominated by other than diffusion current, the ratio, α, of the noise current in unit bandwidth i_n(f = 1 Hz, V_d = −60 mV, and Δf = 1 Hz) to dark current I_d(V_d = −60 mV) was α_SW-d = i_n/I_d ∼ 1 × 10⁻³. The SWIR detectors measured at 0 mV under illuminated conditions had median α_SW-P = i_n/I_ph ∼ 7 × 10⁻⁶. For mid-wave infrared (MWIR) detectors, α_MW-d = i_n/I_d ∼ 2 × 10⁻⁴, due to tunneling current contributions to the 1/f noise. Measurements on forty-nine 1000-μm-diameter MWIR detectors under illuminated conditions at 98 K and −60 mV bias resulted in α_MW-P = i_n/I_ph = 4.16 ± 1.69 × 10⁻⁶. A significant point to note is that the photo-induced noise spectra are nearly identical at 0 mV and 100 mV reverse bias, with a noise-current-to-photocurrent ratio, α_MW-P, in the mid 10⁻⁶ range. For long-wave infrared (LWIR) detectors measured at 78 K, the ratio, α_LW-d = i_n/I_d ∼ 6 × 10⁻⁶, for the best performers. The majority of the LWIR detectors exhibited α_LW-d on the order of 2 × 10⁻⁵. The photo-induced 1/f noise had α_LW-P = i_n/I_ph ∼ 5 × 10⁻⁶. The value of the noise-current-to-dark-current ratio, α appears to increase with increasing bandgap. It is not clear if this is due to different current mechanisms impacting 1/f noise performance. Measurements on detectors of different bandgaps are needed at temperatures where diffusion current is the dominant current. Excess low-frequency noise measurements made as a function of detector reverse bias indicate 1/f noise may result primarily from the dominant current mechanism at each particular bias. The 1/f noise was not a direct function of the applied bias.     

锂离子电池用聚合物电解质的最新进展II.含液聚合物电解质

由于干态聚合物电解质目前还不能满足聚合物锂离子电池的应用要求,人们致力于开发含液体增塑剂的聚合物电解质,包括凝胶型和微孔型两类体系。本文综述了含液聚合物电解质的最新进展,重点论述了各种新体系和新方法。     

离子注入中污染的产生及防护

本文概述了离子注入过程中污染产生的原因和防止污染的措施，特别强调了对微粒污染和金属污染的防护以满足ＵＬＳＩ加工对离子注入的要求。     

Clarification of a wheat straw‐derived medium with ion‐exchange resins for xylitol crystallization

BACKGROUND: Xylitol bioproduction from lignocellulosic residues comprises hydrolysis of the hemicellulose, detoxification of the hydrolysate, bioconversion of the xylose, and recovery of xylitol from the fermented hydrolysate. There are relatively few reports on xylitol recovery from fermented media. In the present study, ion‐exchange resins were used to clarify a fermented wheat straw hemicellulosic hydrolysate, which was then vacuum‐concentrated and submitted to cooling in the presence of ethanol for xylitol crystallization. RESULTS: Sequential adsorption into two anion‐exchange resins (A‐860S and A‐500PS) promoted considerable reductions in the content of soluble by‐products (up to 97.5%) and in medium coloration (99.5%). Vacuum concentration led to a dark‐colored viscous solution that inhibited xylitol crystallization. This inhibition could be overcome by mixing the concentrated medium with a commercial xylitol solution. Such a strategy led to xylitol crystals with up to 95.9% purity. The crystallization yield (43.5%) was close to that observed when using commercial xylitol solution (51.4%). CONCLUSION: The experimental data demonstrate the feasibility of using ion‐exchange resins followed by cooling in the presence of ethanol as a strategy to promote the fast recovery and purification of xylitol from hemicellulose‐derived fermentation media. Copyright © 2008 Society of Chemical Industry     

锂离子电池有机电解液成膜添加剂的研究现状

文章综述了锂离子电池有机电解液成膜添加剂的作用原理，具体介绍了CO2、SO2、VC化合物、卤化物、有机铜盐以及马来酐等添加剂的研究现状。     

Hydrogen production in solid electrolyte membrane reactors (SEMRs)

In the present work, the prospects and trends of solid electrolyte membrane reactors (SEMRs) towards hydrogen production, are discussed. Initially, an overview of the principles, the properties and the techniques related to the usage of the SEMRs, are presented. In the following, a literature survey covering earlier and recent developments of the various methods (e.g. reforming or partial oxidation or dehydrogenation of hydrocarbons, steam electrolysis) employed in the SEMRs for the production of hydrogen, is performed. Finally, the current status of this research field is analyzed and future research topics are proposed.     

Effect of Rare Earth Element Cerium on Mechanical Properties and Morphology of TiN Coating Prepared by Arc Ion Plating

TiN coatings were deposited on polished substrates of W18Cr4V high speed steel by means of vacuum arc ion plating. The effect of cerium on adhesion between TiN coating and substrate was studied. The microstructures and composition of TiN coatings were also investigated by means of scanning electron microscope (SEM), Auger electron spectroscopy (AES), and X-ray diffraction (XRD) technique. It was found that cerium is an effective modifying agent and the addition of suitable amount of cerium to TiN coatings can produce relatively excellent properties such as micro-hardness, wear resistance, oxidation resistance and porosity. The experimental results show that the added cerium in TiN coatings makesa contribution to form the preferred direction along with a (111 ) or (222) close packed face, which may be one of the reasons that improves some properties mentioned above.     

Nonlinear electrical transport in K-TCNQ at low temperatures

A remarkable nonlinearity has been observed for electric transport in K-TCNQ (potassium tetracyanoquinodimethane) quasi-one-dimensional conductor. The negative differential resistance region appears afterV _m (turn over voltage), beyond which voltage goes down with increase of current. A possible mechanism is discussed in terms of dynamics of charged solitons and domain walls in one-dimensional molecular stacks of these types of crystals.     

Catalytic oxidation of sulphide ions to elementary sulphur in aqueous solutions over transition metal oxides

The catalytic activity of a wide range of transition metal oxides in oxidation of sulphide ions by air in aqueous medium was studied. Some specific features of the reaction mechanism on some of the studied oxides were considered. The transition metal oxides are promising catalysts for practical application. Some of these oxides will allow the preparation of catalysts possessing activity comparable to that of the cobalt phthalocyanine based catalysts, popular in industrial practice.