Transient liquid phase sintering of high-purity mullite for high-temperature structural ceramics

High-purity mullite ceramics, promising engineering ceramics for high-temperature applications, were fabricated using transient liquid phase sintering to improve their high-temperature mechanical properties. Small amounts of ultrafine alumina or silica powders were uniformly mixed with the mullite precursor depending on the silica-alumina ratio of the resulting ceramics to allow for the formation of a transient liquid phase during sintering, thus, enhancing densification at the early stage of sintering and mullite formation by the reaction between additional alumina and the residual glassy phase (mullitization) at the final stage of sintering. The addition of alumina powder to the silica-rich mullite precursor resulted in a reaction between the glassy silica and alumina phases during sintering, thereby forming a mullite phase without inhibiting densification. The addition of fine silica powder to the mullite single-phase precursor led to densification with an abnormal grain growth of mullite, whereas some of the added silica remained as a glassy phase after sintering. The resulting mullite ceramics prepared using different powder compositions showed different sintering behaviors, depending on the amount of alumina added. Upon selecting an optimum process and the amount of alumina to be added, the pure mullite ceramics obtained via transient liquid phase sintering exhibited high density (approximately 99%) and excellent high-temperature flexural strength (approximately 320 MPa) at 1500 °C in air. These results clearly demonstrate that pure mullite ceramics fabricated via transient liquid phase sintering with compositions close to those of stoichiometric mullite could be a promising process for the fabrication of high-temperature structural ceramics used in an ambient atmosphere. The transient liquid phase sintering process proposed in this study could be a powerful processing tool that allows for the preparation of superior high-temperature structural ceramics used in the ambient processing atmosphere.     

Pulsed Electromagnetic Field Stimulation in Osteogenesis and Chondrogenesis: Signaling Pathways and Therapeutic Implications

Mesenchymal stem cells (MSCs) are the main cell players in tissue repair and thanks to their self-renewal and multi-lineage differentiation capabilities, they gained significant attention as cell source for tissue engineering (TE) approaches aimed at restoring bone and cartilage defects. Despite significant progress, their therapeutic application remains debated: the TE construct often fails to completely restore the biomechanical properties of the native tissue, leading to poor clinical outcomes in the long term. Pulsed electromagnetic fields (PEMFs) are currently used as a safe and non-invasive treatment to enhance bone healing and to provide joint protection. PEMFs enhance both osteogenic and chondrogenic differentiation of MSCs. Here, we provide extensive review of the signaling pathways modulated by PEMFs during MSCs osteogenic and chondrogenic differentiation. Particular attention has been given to the PEMF-mediated activation of the adenosine signaling and their regulation of the inflammatory response as key player in TE approaches. Overall, the application of PEMFs in tissue repair is foreseen: (1) in vitro: to improve the functional and mechanical properties of the engineered construct; (2) in vivo: (i) to favor graft integration, (ii) to control the local inflammatory response, and (iii) to foster tissue repair from both implanted and resident MSCs cells.     

On the thermally-induced seizure in bearings: A review

This paper presents a state-of-the-art survey of papers reported on the nature of a troublesome failure mode in bearings known as seizure. This mode of failure is thermally-induced and it occurs in both journal and rolling element bearings. To gain insight, particular attention is given to reported experimental observation, various mechanisms involved, and available prediction methodologies.     

Improved synergetic excitation control for transient stability enhancement and voltage regulation of power systems

This paper proposes decentralized improved synergetic excitation controllers (ISEC) for synchronous generators to enhance transient stability and obtain satisfactory voltage regulation performance of power systems. Each generator is considered as a subsystem, for which an ISEC is designed. According to the control objectives, a manifold, which is a linear combination of the deviation of generator terminal voltage, rotor speed and active power, is chosen for the design of ISEC. Compared with the conventional synergetic excitation controller (CSEC), a parameter adaptation scheme is proposed for updating the controller parameter online in order to improve the transient stability and voltage regulation performance simultaneously under various operating conditions. Case studies are undertaken on a single-machine infinite-bus power system and a two-area four-machine power system, respectively. Simulation results show the ISEC can provide better damping and voltage regulation performance, compared with the CSEC without parameter adaptation scheme and the conventional power system stabilizer.     

Animations showing Lego manipulative tasks: Three potential moderators of effectiveness

Evidence suggests that transient visual information, such as animations, may be more challenging to learn than static visualizations. However, when a procedural-manipulative task is involved, our evolved embodied cognition seems to reverse this transitory challenge. Hence, for object manipulative tasks, instructional animations may be more suitable than statics. We investigated this argument further by comparing animations with statics using a Lego task shown to university students, by examining three potential moderators of effectiveness: (a) the environment of manipulation (virtual or physical), (b) the quality of visual information (focused or unfocused), and (c) the presence of hands (no hands or with hands). In Experiment 1 we found an advantage of animation over statics, and no differences among the environments. In Experiment 2, we again observed an animation advantage, a small advantage of focused static information compared to unfocused static information, and a positive effect of not showing the hands.     

双河油田注入水适应性及注水井酸化解堵研究

考察了双河油田双河联、江河联注入水堵塞地层的因素;膨胀性黏土，悬浮固体颗粒。细菌及悬浮污油。含膨胀性黏土的双河南、双河北及不含膨胀性黏土的双江岩心粉，在注入水中相对于地层水中的体积膨胀度分别为14．5％、11．1％及0．02％；注入100PV不含悬浮颗粒的等体积比地层水、注入水混合水使双河、双江岩心渗透率分别下降7％和4％、9％和7％。注入水中悬浮颗粒引起岩心渗透率下降，粒径越大、颗粒浓度越大、注入量越大，则渗透率越低。在粒径2．1μm或颗粒浓度3mg／L前后下降幅度变化较大。注入水中硫酸盐还原菌引起岩心渗透率下降，含菌量越大则渗透率开始下降时的注水量越小，注入含菌50个／L的水100PV使岩心渗透率下降7％。岩心对注水合油量敏感，注入含油量20mg／L的水50PV使岩心渗透率下降20％。在岩心注水实验中渗透率下降最严重的是双河南岩心，其次是双河北岩心．江河岩心较轻，注入精细过滤水的双河北岩心渗透率下降大大减少．说明悬浮固体是造成注水堵塞的主要因素。为了解除双河油田注水井的堵塞，研制了含黏土稳定剂、缓蚀剂、铁离子稳定剂、互溶剂的土酸液，与南阳油田使用的低伤害酸液一起，用于1口注水井的解堵，效果良好。图7表4参5。     

一种二元域上的快速计算哈希函数

论文从映射的角度,将哈希函数分为三类:严格哈希函数、计算哈希函数和实用哈希函数。在此基础上,根据二元域上二次方程x2 x c=0的部分不可解的性质,构造了一种计算哈希函数,它满足单向性和一一对应性,同时具有运算速度快的优点。     

Science in High Magnetic Fields: What Could Be Learned?

High magnetic fields are one of the most powerful tools available to scientists for the study, modification and control of matter. This includes the knowledge on correlations effects, interaction mechanisms, structural information and understanding of mesoscopic effects. In this context, a review of recent scientific achievements at the Grenoble High Magnetic Laboratory is given to illustrate, on specific examples, the power of the Magnetic Field probe.     

用Delphi实现快速删除TList的批连续结点算法的探讨

在编制遥测数据处理软件的过程中，面对大量的测试数据，经常需要编写高效率的数据过滤器。本文讨论了一种通过采用跨单元、跨类访问Delphi类的私有域的方法实现快速删除TList批连续结点的新算法，并通过测试结果得到验证。     

低温低渗透砂岩油藏窜流大孔道深部封堵技术研究

所用堵剂为高强度的淀粉接枝聚丙烯酰胺交联凝胶SAMG-1,由<6%淀粉、4.5%-5.5%丙烯酰胺、0.003%-0.006%交联剂组成,35℃成胶时间受淀粉和交联剂用量控制,为18-20小时以上,成胶前黏度-100 mPa.s。该堵剂具有长期稳定性,在储层岩心中注入深度15 cm的堵剂,在35℃候凝48小时后及老化90天后,封堵强度分别为0.61和0.59 MPa/cm,封堵率分别为98.6%和98.1%。该堵剂优先进入高渗层,注入0.5 PV并成胶后,2组双填砂管组成的模型低、高渗管渗透率保留率分别为68.4%、0.7%和69.4%、0.0%。吉林扶余油田西一区+15-8.2区块有水井6口,油井13口,含水率达91.5%,注入水最快在5天内到达油井。报道了该区块整体深部调剖封堵窜流通道的情况,详细叙述了+15-9.2井施工中通过注入压力和井底回压控制注入流量,使堵剂陆续进入原生和次生孔道的工艺作业,该井设计注入堵剂92 m3。6口水井整体调剖后,油井产液量差别减小,产油量增加,有效期已超过了9个月,共增油843 t,含水平均下降3.87%。图7表1参8。