复合材料层合曲梁分层问题的解析解法

根据叠加原理将含有分层的复合材料层合曲梁在横向载荷作用下的受力状态分解为在面受力状态与出面受力状态,再将出面受力状态分解为无分层曲梁受横向载荷状态与含分层曲梁承受附加剪切载荷状态。将分层问题归结为在附加剪切载荷状态中,层合梁附加位移与附加应力的分析,并据此建立了一个简单的力学模型。最后得到了由分层引起的附加位移与应力的解析解答,并用能量释放率方法确定了应力强度因子。     

谈地下室工程的防水

就地下室工程的防水,从设计、混凝土自防水、附加防水层的设置及各种附加防水层的分析与比较、多道设防综合治理、系统防水等方面,笔者提出了自己的见解或建议。     

徐淮地区煤矿井筒破裂机理研究

从徐淮地区井筒破裂的特点出发，分析引起井壁破裂的根本原因，据此提出井筒的破裂机理，为选择防治井筒破裂的方法提供依据     

利用独立分量分析法去除地震噪声

 独立分量分析（ICA）作为盲源分离（BSS）的一种新方法,是分解观测数据中独立信息的有力工具。以往的ICA算法一般假设噪声可以忽略不计，而实际的观测数据中又常常包含一些加性噪声。对于加性噪声的影响不能忽略的情况下，改进的ICA算法首先利用非零时间滞后协方差，应用两步特征值分解法(EVD)可成功地去除部分加性噪声的影响；再利用ICA算法就能更好地分离出原信号。本文通过对地震理论模型和实际资料的试验，说明改进的ICA算法能够有效地克服加性噪声对常规ICA算法的影响，能够分离出地震资料中的有效信号，从而实现利用独立分量分析压制地震资料噪声的目的。     

真空钙热还原炉渣的综合利用研究

研究了从真空钙热还原炉渣中回收稀土的工艺条件；采用本工艺得到的合格稀土溶液，其回收率达65．41％；副产品氟化钙用作炼硅铁合金的助熔剂，使钙热还原炉渣得到综合利用。     

论包装的功能价值与商品附加值

文中从包装与包装的功能价值、商品附加值及其开发、包装与商品附加值等方面进行了论述。     

流体在环形狭缝中流动时园柱体的微振动

本文讨论了在两个园柱体的环形狭缝中不可压缩流体的流动．在一定的假设下，运用流体力学方程和流体对柱体的作用方程，导出了附加质量和转动惯量、振动频率和衰减系数．并对文（１）中的某些结果进行了必要的修正．     

High growth rate process in a SiC horizontal CVD reactor using HCl

The results of a new epitaxial process using an industrial 6 × 2″ wafer reactor with the introduction of HCl during the growth have been reported. A complete reduction of silicon nucleation in the gas phase has been observed even for high silicon dilution parameters (Si/H₂ > 0.05%) and an increase of the growth rate until about 20 μm/h has been measured. Photoluminescence at room temperature and at 50 K was used for defects quantification and distribution. On these wafers grown using HCl high voltage Schottky diodes have been realized. The diodes were analyzed by current-voltage (I-V) characteristics.     

Single and combined deactivating effect of alkali metals and HCl on commercial SCR catalysts

Two commercial SCR catalysts, with a nominal W content of about 9 wt.% and a V nominal content of 0.55 and 1.8 wt.%, respectively, were contacted with different amounts of Na and K and with HCl vapours in order to simulate poisoning by species more specifically contained in exhaust gases from MSW combustion. Catalysts were characterised using XRD analysis, SEM/EDX analysis, BET and pore size distribution measurements, NH₃ TPD, TG analysis. Poisoning agents do not cause loss of surface area nor pore occlusion. A significant loss of surface acidity was observed upon alkali metals poisoning whereas a decreasing of vanadium content was observed for the more concentrated catalysts upon HCl poisoning. Catalysts deactivation is proportional to the number of acid sites neutralised by alkali metals adsorbing ammonia in the temperature range typical of SCR process. HCl promotes the formation of new acid sites showing a lower activity compared to the original one.     

Preparation,characterization and in vitro drug release properties of polytrimethylene carbonate/polyadipic anhydride blend microspheres

Polyadipic anhydride (PAA), an aliphatic polyanhydride, and polytrimethylene carbonate (PTMC), an aliphatic polycarbonate, were synthesized via ring opening polymerization of oxepan‐2,7‐dione and melt‐condensation of trimethylene carbonate (1,3 dioxan‐2‐one), respectively. PTMC–PAA blend microspheres containing different ratios of buprenorphine HCl (2, 5, and 10%) were prepared by an oil‐in‐oil emulsion solvent removal method. Microspheres with different ratios of PTMC–PAA (85/15, 70/30, and 55/45) containing 5% buprenorphine HCl were prepared. Microspheres were spherical with visible cracks and pores on the surface. The average particle size of microspheres was around 200 μm for all microspheres. Drug loading efficiency of PTMC–PAA microspheres (85/15, 70/30, and 55/45) was 97.2, 95.2, and 70.2%, respectively. With the increase in the PTMC ratio, the melting point and the enthalpy of melting were both decreased. The mechanism for drug release from PTMC–PAA blend microspheres were generally a combination of drug diffusion through polymers and biodegradation of the polymers. In first three days, the release from microspheres followed zero order kinetics and was dependent on the PAA content. After three days the drug release from microspheres followed first order kinetics. In conclusion it was demonstrated that buprenorphine HCl release from microspheres could be successfully controlled by using different ratios of PTMC–PAA blends. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2377–2383, 2006