Complex study of protective Cr3C2–NiAl coatings deposited by vacuum electro-spark alloying,pulsed cathodic arc evaporation,magnetron sputtering,and hybrid technology

Coatings were obtained by vacuum electro-spark alloying (VESA), pulsed cathodic arc evaporation (PCAE), magnetron sputtering (MS) techniques and VESA-PCAE-MS hybrid technology using Cr₃C₂–NiAl electrodes. The structure of the coatings was analyzed using scanning and transmission electron microscopy, X-ray diffraction and energy-dispersive spectroscopy. Mechanical properties were determined by nanoindentation, while tribological properties were assessed using pin-on-disk tribometer. Corrosion resistance was estimated by voltammetry in 1 N H₂SO₄ and 3.5%NaCl solutions. Oxidation resistance tests were performed at 800°С in air. The VESA coating had the highest thickness, low friction coefficient and high wear resistance. PCAE coating demonstrated the highest hardness (24 GPa) and elastic recovery (59%), oxidation resistance and superior corrosion resistance both in 1 N H₂SO₄ (i_corr = 70 μА/cm²) and 3.5%NaCl (i_corr = 0.74 μА/cm²) solutions. The MS coating had average mechanical properties and low corrosion current density (71 μА/cm²) in 1 N H₂SO₄. Deposition of coatings using VESA-PCAE-MS hybrid technology led to an increase in corrosion and oxidation resistance at least by 1.5 times in comparison with the VESA coating.     

Off‐grid DoA estimation method of wideband signals

In this paper, an off‐grid direction of arrival (DoA) estimation method is proposed for wideband signals. This method is based on the sparse representation (SR) of the array covariance matrix. Similar to the time domain DoA estimation methods, the correlation function of the sources was assumed to be the same and known. A new measurement vector is obtained using the lower‐left triangular elements of the covariance matrix. The DoAs are estimated by quantizing the entire range of continuous angle space into discrete grid points. However, the exact DoAs may be located between two grid points; therefore, this estimation has errors. The accuracy of DoA estimation is improved by the minimization of the difference between the new measurement vector and its estimated values. Simulation results revealed that the proposed method can enhance the DoA estimation accuracy of wideband signals.     

干扰条件下的“北斗”信号解扩重构DOA估计

在干扰条件下，卫星导航抗干扰波束形成算法往往需要卫星信号波达方向（Direction-of-Arrival，DOA）的先验信息。但当存在低信噪比信号或主动干扰源时，常规的DOA估计算法性能急剧下降甚至失效。针对此问题，提出了一种被干扰信号压制的低信噪比“北斗”信号的DOA估计算法。该算法首先通过对接收信号进行子空间投影抑制干扰信号，然后对抑制干扰后的信号进行解扩重构处理，最后通过多重信号分类算法完成对“北斗”信号的DOA估计。仿真结果表明，在干扰信号干信比80 dB条件下，“北斗”信号DOA估计误差在5°以内，为下一步进行波束形成计算提供了高精度的入射角信息。     

An automated treatment planning strategy for highly noncoplanar radiotherapy arc trajectories

Radiation therapy is a technology-driven cancer treatment modality that has experienced significant advances over the last decades, due to multidisciplinary contributions that include engineering and computing. Recent technological developments allow the use of noncoplanar volumetric modulated arc therapy (VMAT), one of the most recent photon treatment techniques, in clinical practice. In this work, an automated noncoplanar arc trajectory optimization framework designed in two modular phases is presented. First, a noncoplanar beam angle optimization algorithm is used to obtain a set of noncoplanar irradiation directions. Then, anchored in these directions, an optimization strategy is proposed to compute an optimal arc trajectory. The computational experiments considered a pool of twelve difficult head-and-neck tumor cases. It was possible to observe that, for some of these cases, the optimized noncoplanar arc trajectories led to significant treatment planning quality improvements, when compared with coplanar VMAT treatment plans. Although these experiments were done in a research environment treatment planning software (matRad), the conclusions can be of interest for a clinical setting: automated procedures can simplify the current treatment workflow, produce high-quality treatment plans, making better use of human resources and allowing for unbiased comparisons between different treatment techniques.     

Nonuniform linear array DOA estimation using EM criterion

In this letter, we address the problem of Direction of Arrival (DOA) estimation with nonuniform linear array in the context of sparse Bayesian learning (SBL) framework. The nonuniform array output is deemed as an incomplete-data observation, and a hypothetical uniform linear array output is treated as an unavailable complete-data observation. Then the Expectation-Maximization (EM) criterion is directly utilized to iteratively maximize the expected value of the complete-data log likelihood under the posterior distribution of the latent variable. The novelties of the proposed method lie in its capability of interpolating the actual received data to a virtual uniform linear array, therefore extending the achievable array aperture. Simulation results manifests the superiority of the proposed method over off-the-shelf algorithms, specially on circumstances such as low SNR, insufficient snapshots, and spatially adjacent sources.     

Contribution of metal vapor mass at periphery part of pulsed arc to electromagnetic force in weld pool

The arc welding has been used in various welding methods because it is inexpensive and high in strength after welding. However, it is a problem that accidents such as collapse of the bridge occur because of the welding defects. The welding of low cost and high productivity is required without the welding defects. The pulsed TIG welding is inexpensive and capable of high‐quality welding. The electromagnetic force contributing to penetration changes because the transient response of arc temperature and iron vapor generated from anode occurs. However, the analysis of pulsed TIG welding with metal vapor has been elucidated only metal vapor concentration near anode with transient phenomenon and heat flux. Thus, the theoretical elucidation of penetration depth with control factor has not been researched. In this paper, the contribution of metal vapor mass at the periphery part of pulsed arc to the electromagnetic force in the weld pool is elucidated. As a result, the iron vapor mass at periphery part decreased with increasing the frequency. The iron vapor was stagnated at axial center within one cycle. The electromagnetic force to the penetration depth direction in weld pool increased at axial center. Therefore, the metal vapor mass at periphery part plays an important role for the electromagnetic force increment at axial center.     

基于三相幅度测量的相控阵天线快速校准方法

提出了一种基于三相幅度测量的相控阵天线快速校准方法。该方法将天线阵列进行分组,利用每种分组在三种配相下的阵面合成场幅度测量值,可解算出各个天线单元的初始幅相值。该方法仅需幅度测量,避免了相位测量误差影响单元幅相值的计算精度,而且所需幅度测量次数仅为(2N+1)次,可显著提高校准时效性。另外,利用分组思想,同时改变多个单元相位,使总辐射场的幅度变化显著,提升校准准确性。仿真结果表明:校准后相位均方根误差为2.2°,幅度均方根误差为0.2 dB。     

Study on maximum power point tracking of photovoltaic array in irregular shadow

Traditional maximum power point tracking (MPPT) methods can hardly find global maximum power point (MPP) because output characteristics curve of photovoltaic (PV) array may have multi local maximum power points in irregular shadow, and thus easily fall into the local maximum power point. To address this drawback, Considering that sliding mode variable structure (SMVS) control strategy have such advantages as simple structure, fast response and strong robustness, and P&O method have the advantages of simple principle and convenient implementation, so a new algorithm combining SMVS control method and P&O method is proposed, besides, PI controller is applied to reduce system chattering caused by switching sliding surface. It is applied to MPPT control of PV array in irregular shadow to solve the problem of multi-peak optimization in partial shadow. In order to verity the rationality of the proposed algorithm, the experimental circuit is built, which achieves MPPT control by means of the proposed algorithm and P&O method. The experimental results show that compared with the traditional P&O algorithm, the proposed algorithm can fast track the global MPP, tracking speed increases by 60% and the relative error decreased by 20%. Moreover, the system becomes more stable near the MPP, the fluctuations of output power is greatly reduced, and thus make full use of solar energy.     

Bond graph modeling,design and experimental validation of a photovoltaic/fuel cell/ electrolyzer/battery hybrid power system

This work presents a complete bond graph modeling of a hybrid photovoltaic-fuel cell-electrolyzer-battery system. These are multi-physics models that will take into account the influence of temperature on the electrochemical parameters. A bond graph modeling of the electrical dynamics of each source will be introduced. The bond graph models were developed to highlight the multi-physics aspect describing the interaction between hydraulic, thermal, electrochemical, thermodynamic, and electrical fields. This will involve using the most generic modeling approach possible for managing the energy flows of the system while taking into account the viability of the system. Another point treated in this work is to propose. In this work, a new strategy for the power flow management of the studied system has been proposed. This strategy aims to improve the overall efficiency of the studied system by optimizing the decisions made when starting and stopping the fuel cell and the electrolyzer. It was verified that the simulation results of the proposed system, when compared to simulation results presented in the literature, that the hydrogen demand is increased by an average of 8%. The developed management algorithm allows reducing the fuel cell degradation by 87% and the electrolyzer degradation by 65%. As for the operating time of the electrolyzer, an increment of 65% was achieved, thus improving the quality of the produced hydrogen. The Fuel Cell's running time has been decreased by 59%. With the ambition to validate the models proposed and the associated commands, the development of this study gave rise to the creation of an experimental platform. Using this high-performance experimental platform, experimental tests were carried out and the results obtained are compared with those obtained by simulation under the same metrological conditions.     

低觉醒脑电识别与唤醒的可穿戴系统研究

为智能化地识别警戒作业人员出现的低觉醒、注意力下降的生理状态，本文介绍了一种基于FPGA和脑电信号处理的低觉醒状态检测与唤醒系统，系统通过传感器从大脑头皮采集脑电信号，转换为数字信号，经傅里叶变换获取了脑电信号的θ相对能量、α相对能量、重心频率、谱熵等4个特征量，由4个特征量表征低觉醒状态并运用支持向量机对低警戒状态进行识别，当识别出低觉醒状态时采用声音报警模块发出声音，唤醒警戒作业人员。设计系统能够较好地识别出低觉醒状态，识别率达90.8%，可为提高警戒作业工作绩效提供一种可穿戴的智能装备。